nissan navara d40 ecu reset fastest way 2.5dci yd25DDTi

resetting nissan navara d40 ecu.. fastest way to reset ecu.. reset ng ecu navara madaling paraa
paano mag reset ng ECU electronic computer unit
How to reset ecu or Resetting Electronic Computer Unit after installing SCV or other sensors that needs to be friendly with your computer reason why after installing problem doesnt go away because the computer has to learn the new electronic device to function well and that is restting it. Do this for basic diy after installing electronic parts. Hope this helps. Done this after replacing my SCV suction control valve which controls fuel. when you have iddling issues ex. the engine stops when parked or idling, engine shakes when stepping on gas, engine dies when doing a turn or at a stop light. that makes SCV the problem in most cases,, First just clean it up then ecu reset if it didnt work get a new scv the do ecu reset and go.. drive safe everyone!

[@DaveCadz-zo4ff]

Thanks for a big help to reset navara d40 nissan

[@karengaleespinas8168]

Great it works for my nissan navara

[@claydosibid5626]

Perfect help for reseting an ecu

[@davidsonmarkespinas8242]

Ok naman ang steps on how to reset the ecu of nissan navara d40 yd25ddti

[@noselagsovadac9509]

Nice

[@davidsonespinas1656]

Thanks for sharing on how to reset the ecu of my nissan d40 yd25

[@JohnKenlly09]

Great help on how to reset ecu navara

[@danielbarbosa-cm3xs]

perfect🤝🤝🤝🤝🤝🤝🤝🤝🤝🤝

[@joshuaespinas2799]

great help boss .thank you

[@marccadz3630]

Ana rana ka simple

[@joshuaespinas2799]

haahah

[@davidsonmarkespinas8242]

Thanks for sharing your ideas

[@marccadz3630]

My pleasure 😊

[@joshuaespinas2799]

ok namn

[@Satyendar930]

Thanks

[@robhi3518]

Thanks for information. How do you deal with limp mode?

[@kodigoodman6417]

Reckon it would help with my vdc and traction light's,?

[@ThomasJosephCHARLIE-vu2cg]

Can I do the same setting to NV350 E26 to reset ECU or what is the steps?

[@marccadz3630]

You can have a try please let us know if it works too

[@nathanielsagcelo3573]

Gd pm sir may Ron den Yan sa navara ko naka 4LO

[@marccadz3630]

Baka naka activate 4x4 mo

[@DaveCadz-zo4ff]

Meron yan basta may ecu

[@roadrasher8913]

What is the reason for doing this? I have to replace my boost solenoid should I do this after I change it? Also would it wipe a power
Map off if it has been put o

[@marccadz3630]

Yes so that your ecu can communicate new sensors properly it will help them to read and register new parts specially electronic

[@brianmcleod4772]

Does it effect a remap on the ecu?

[@roadrasher8913]

@@brianmcleod4772 didn’t effect mine

[@tim0thyding]

Thanks! But... how can we tell if the reset procedure is successful?

[@marccadz3630]

When you can see the flashing light at the end it should blink 10times other than that means other issues for scanning

[@adamtoh6619]

its look like same step of resetting SCV right??

[@marccadz3630]

Yes same

[@xiaomiipadcongregation959]

You didn't show that its now ok that the engine light has turned off

[@lukwoz1302]

What about np300

[@marccadz3630]

I think its the same just try it

[@lukwoz1302]

Na didn't do anything

[@marccadz3630]

@@lukwoz1302 works fine with me as long as you follow the steps