The motorised part was what drew me here, so little disappointed that it's not shown. The actual build and versatility is impressive, given it covers different angles, it's also nice that it requires no special tools. Nice vid!
Reminds me of how a roller coaster has wheels on opposite sides of a rail… Very simple design that just works. Still, curious how much the friction increases once there is a load put on the slider. Poss. Idea for a 2.0 version… Create a slot for the heads of the bolts, so they cannot rotate. Bend bolt out 45°, then add 1st roller bearing, bend back 90° & add 2nd bearing. The slots on top of the slider will ensure the head of the bolt does not rotate & maintains a perpendicular alignment of the 45° & 90° bends. Now, with the roller bearings being perpendicular as well, they will sit flush the the corners of the square tubing; which should significantly improve the coefficient of friction between the slider & the tubing after a load is added to the slider.
I like the design application, especially using opposite corners on square tubing as a “track”. Like many others, I too was disappointed that there is no portion about making it “motorized”. 🤨 Maybe retitle video as ‘Make An Awesome *Chassis For* A Motorized Slider’? …or just add ‘Part 1’ lol
Aunque en realidad asi no se deberían usar esos rodamientos y menos para portones, tendría que ir a cambiarlos por garantía en unos pocos dias, estarían funcionado mal bajo peso.
cool but it can't take much load since thouse bearings are supposed to be used vertically not at an angle. you need tapered bearings for propper load bearing.
Limba rusa nu este universala! Daca eu scriu in limba materna, tu intelegi ceva? Eu stiu si turca, tu stii? In turca iti zic "hai sictir"! Good luck cu asta! :)
ME GUSTA LA IDEA,SENCILLA PARA ELIMINAR LA CREMALLERA DE PORTON ELECTRICO,Y ADAPTARLO AL PORTON DE GARAGE- CON GUAYAS.LAS CREMALLERA ESTAN CARAS+GRACIAS GRACIAS.Y BENDICIONES
I'm looking for a design to use on a chainsaw mill im going to build. I have some 12ft T beams I'm gonna use as rails for chainsaw rig to slide. It 1/4 inch thick and 2 1/2 wide on flat face. My idea so far is to buy some metal hole saws and make some washers. Two big one small with a 22mm hole to put a skateboard wheel bearing in. Might make a press fit and weld a keeper on the sides so bearing stays in.
It was sympathetic to fixing the bearings, but my first tests yielded unexpected results: With the bearings, it became noticeable that the screw did not "close" completely perpendicular to a threaded rod, as if the rise of the thread had a slight effect. But maybe if I had looked with a better quality screw it would have been good. Or will this solution always bring a little "skew" to the bearing?
Maybe a finer thread count would help, or make it less noticeable? Or maybe a spring type lock washer. That would have the added benefit of keeping tings from vibrating loose over time. Not sure if either of those would help but I thought I'd share either way!
I have one experiment for making car to move on sliding ice. You imagine vahical tyres moving, now imagine sliding strip. Now think how we can connect it. Mean using sliding ice strip at the bottom of car but control by wheels, we will fix strip at the bottom of tyres to move car in ice. Movement of car tyres will slide the strip either of iron or wood. Keep speed of 20 or 40.km. to have better grip. Staring will give direction to left ,right. No change in car engine, same engine, same driving system ,every thing must in extra attachment below tyres. We can avoid many accident. Think in this direction. Jay bharat.
Wheels of car Wheels rotate the ball bearing. Question is if weight. Wood or iron will take weight and everything will get adjusted in ice. Jay bharat.
The motorised part was what drew me here, so little disappointed that it's not shown.
The actual build and versatility is impressive, given it covers different angles, it's also nice that it requires no special tools.
Nice vid!
J
Cgvgghhjvh
Me too.
Right !!!!
Перевод
Reminds me of how a roller coaster has wheels on opposite sides of a rail…
Very simple design that just works. Still, curious how much the friction increases once there is a load put on the slider.
Poss. Idea for a 2.0 version…
Create a slot for the heads of the bolts, so they cannot rotate. Bend bolt out 45°, then add 1st roller bearing, bend back 90° & add 2nd bearing.
The slots on top of the slider will ensure the head of the bolt does not rotate & maintains a perpendicular alignment of the 45° & 90° bends. Now, with the roller bearings being perpendicular as well, they will sit flush the the corners of the square tubing; which should significantly improve the coefficient of friction between the slider & the tubing after a load is added to the slider.
I like the adaptability of the slide ! Great work but one question .......... Where's the motor and the hooked up system ? , .........
That's a very green motor you've got there. Powered by pizza and beer.
Great idea! Will it work outside too? In snow and rain?
deep groove ball bearings are not meant for axial forces, you'll ruin the bearings in just a couple of days
What is? I'm looking for something very strong to slide a metal frame in... Not sure what to look for tbh
good 👍👍👍..Thank you Messi 😀
Not sure that the sealed bearings are designed to funtion with downward pressure being applied to their inter sides.
Brother ap ke jaisa hi very smart idea hai bahut sunder
I was planning to buy a slide but after watching this clip of yours, I gave up on that idea. Thank you for sharing
excellent travail, c'est exactement ce que je cherche pour ma machine combinée, qui sera proch sur youtube, merci chef!
Okay. So, where's the motor?
It's still in the hardware store. 🤣🤣🤣
I like the design application, especially using opposite corners on square tubing as a “track”.
Like many others, I too was disappointed that there is no portion about making it “motorized”. 🤨
Maybe retitle video as ‘Make An Awesome *Chassis For* A Motorized Slider’?
…or just add ‘Part 1’ lol
He doesn't understand the meaning of "motorize" he wrote.
Great idea and video. Do you have a video with the motorized part of the design?
Excelente gracias por compartir tus conocimientos saludos cordiales desde Cali Colombia 🇦🇲✌️
Aunque en realidad asi no se deberían usar esos rodamientos y menos para portones, tendría que ir a cambiarlos por garantía en unos pocos dias, estarían funcionado mal bajo peso.
I was looking for the exact parts list in the description below, but I couldn't find it? Any help would be appreciated. Thank you
0:07 i have a bad feelling about this
That's exactly the time I left to read the comments. Thankfully yours was the 2nd one and I didn't waste more time finding someone to agree with.
Amazing I would like to use it on my project.
Great idea. But how does it slide on the flat bar? The bearings are not contacting the side of the bar.
Ingenious idea with scope for a great many applications. Just great. Thanks for sharing.
Awesome! This gives me some great inspiration
is that one of those wish motors? wish you had one.
What a tiny motor. Still unable to spot it..
Good idea
Where exactly is the "motorized" part? And what is this used for?
شكد فرحت من عرفت انك عربي ومبدع بالتوفيق
Good❤
cool but it can't take much load since thouse bearings are supposed to be used vertically not at an angle. you need tapered bearings for propper load bearing.
Exactly where is the motorized part? Did I miss it or is it not even shown? If you are going to say it's motorized then show it!
kkkkkkkkkkkkkkkkkk. I think this is a joke !!
Good idea for example a sliding door
Watching from philippines
looks like that may work on piping as well
Will this work for a round metal pipe too?
Thanks a lot being looking for exactly same slider technique for long. Simple and sweet technique
Good, i like it👍👍👍👍
Thank you so much.....
GOOD JOOB !!!
Regards PP.
Bom trabalho 👍👏
I love you sir 😘😘😘
I am your big fan
thank you BROOOOOOO !
I am live in India
You live in USA....?
You are a big genius TH-camr
Love you sir
thanks my freind
You could use V groove bearings instead for most of these. Where's the motorized part?
a genius slider, and with a leaner actuator, wow
Chia sẽ hay hữu ích
Nice Chanel greetings from the netherlands
Thank you
Wow, great idea!.. 👏
И что это изобретение нам дало??? Машинку которая ездит по металлу? Нужно не много доработать это изобретение и тогда возможно оно и пригодиться
Limba rusa nu este universala!
Daca eu scriu in limba materna, tu intelegi ceva?
Eu stiu si turca, tu stii? In turca iti zic "hai sictir"!
Good luck cu asta! :)
Cool one! Awesome!
is there any way to do it without bearing?
Interesante sistema. En su opiniòn con cual perfil trabaja mejor la guìa?. saludos
Amazing
Good job
Is the best
Interesante sistema. Según opinión con cual perfil trabaja trabaja mejor el deslisador?, queda sin juego una vez ajustado?, saludos.
Great Build, Thanks
отличная каретка для кулибиных. спасибо, лайк.
Вряд ли эти подшипники выдержат нагрузку как радиально-упорные...
Ну дело сделано😊😊
it is not support cnc
Nice video
ME GUSTA LA IDEA,SENCILLA PARA ELIMINAR LA CREMALLERA DE PORTON ELECTRICO,Y ADAPTARLO AL PORTON DE GARAGE- CON GUAYAS.LAS CREMALLERA ESTAN CARAS+GRACIAS GRACIAS.Y BENDICIONES
Simple can make with U groove wheel
Cool work sir 👍👏
Samaz aya kya banaya isna
Interesting design and reminds me of cnc tables. Just makes me want to make a cnc table for my everlast welder even more now.
Those bearing and not designed to be horizontally loaded. They should be vertical.
What Do you mean by "motorized"?
Good question
I want to make a heavy sliding table for my small sawmill.is this method good?
I'm looking for a design to use on a chainsaw mill im going to build. I have some 12ft T beams I'm gonna use as rails for chainsaw rig to slide. It 1/4 inch thick and 2 1/2 wide on flat face. My idea so far is to buy some metal hole saws and make some washers. Two big one small with a 22mm hole to put a skateboard wheel bearing in. Might make a press fit and weld a keeper on the sides so bearing stays in.
Mantap bang salam dari pemula 👍
Nice
Tremendo trabajo felicidades fácil de hacer y eficas
Super 👌
Like 👍
thanks you my frend
Kenapa baru sekarang saya tau.. nice
👍👍👍👍👍👍👍👍👍👍 ok
What ate the sizes of those bearings?
It was sympathetic to fixing the bearings, but my first tests yielded unexpected results: With the bearings, it became noticeable that the screw did not "close" completely perpendicular to a threaded rod, as if the rise of the thread had a slight effect. But maybe if I had looked with a better quality screw it would have been good. Or will this solution always bring a little "skew" to the bearing?
Maybe a finer thread count would help, or make it less noticeable? Or maybe a spring type lock washer. That would have the added benefit of keeping tings from vibrating loose over time. Not sure if either of those would help but I thought I'd share either way!
nice
What is this for, colleague, what use will you give it?
will it work on curve rail?
Motorized by hand!
Grasias x los exelentes videos desde Nicaragua
Nice build, especially the motor lmao
Do you have follow up videos? For completion? Website?
That weird stare at the beginning is gonna be a no from me dawg
Ingenioso, muy bueno, pero faltó lo motorizado
Mantap bos ku
You put .5 bore bearings on .375 bolt for an axle. How is that any kind of precision? Might as well use a skateboard on a 2x4.
I have one experiment for making car to move on sliding ice.
You imagine vahical tyres moving, now imagine sliding strip.
Now think how we can connect it.
Mean using sliding ice strip at the bottom of car but control by wheels, we will fix strip at the bottom of tyres to move car in ice.
Movement of car tyres will slide the strip either of iron or wood.
Keep speed of 20 or 40.km. to have better grip.
Staring will give direction to left ,right.
No change in car engine, same engine, same driving system ,every thing must in extra attachment below tyres.
We can avoid many accident.
Think in this direction.
Jay bharat.
Play with ball bearing, tyres will move ball bearing to push flat wood or iron for more grips on car.
th-cam.com/video/1jqi-fbChrg/w-d-xo.htmlsi=QBQ94VZvSPEAng7j
Wheels of car Wheels rotate the ball bearing. Question is if weight.
Wood or iron will take weight and everything will get adjusted in ice.
Jay bharat.
Se puede usar invertido, para poner doble riel elevado .y soldado a los cochecitos , una base para carga?
Use for what
good
Messi, is that you?
Thanks for your this work.
Very Good!... #301 ✝ {6-24-2022}
Wow you made it to do only that 🤔
good ideas.for good works.
Eda mownee poli sadhnm❤👍
Your channel notification 😍
thank you my frend
Very good brother congratuletions goin Guatemala
Muy excelente
Truly an awesome workmanship of yours and the best that I have come across with its various variations!!