SAM, always good information you share really appreciate ur time buy the way i could not hear you because the voice is to low please increase the volume and as always thanks for sharing been waiting long time for ur videos. cheeeeers
The Audi I had to adapt with ODIS required more key cycles in the test plan....Additionally, I found that the only key that will "work" or start the vehicle afterwards was the key or keys that were present during the process....any keys that are not there are worthless later and the vehicle will act as if you never programmed or adapted....my Audi was a 2013 A3....hope this helps 👍...so for future reference, have all keys present to avoid "potential" call backs later
Sam you mentioned that there are other tools that this can be done with, could you share a link to the forum that you mentioned where they are discussing this sort of thing, I changed my transmission on an 09 A4 and would hate to take it to the stealer to get this done.
Hi, Im writing from México. Aré you able to share step by step programing of the mechateonic Unit for Audi 2016? Un México Is expensive, expensive, expensive. Can you help me?
Hi, I am trying to get more information on how to perform a TCU update, calling around the service shops in the area and they never can answer or call back. Looking at AliExpress ODIS interfaces... but how will I log in to retrieve the TCU update firmware/reflash? I have several questions as to how you obtained your setup and etc, thanks in advance if you can shed any light or help guide me in the right direction. I am not now to ECU reflashing, just VW ECU's haha.
Had no idea vcm2 would work,,, I have a mongoose Ford one,, would you know if that would work also,,, I do got a Audi im needing to sync the vins as the original ecm went toast,,
So, does this pretty much mean that the reprograming of the transmission is simply just a security protocol, adapting the new part to the ECU? Don't suppose you know if a different code trans can be programmed, my current is MKE 2011 and I would like to fit 2014 PWW?
@@toolhutusaakathecarflasher3019 okay. I did online programming but it says the vehicle key is not OE it’s a Aftermarket key so the programming cannot be performed. Whether it’s ture? But vehicle was running with the same key for a long time. The massage popped up while programming ( Key not assigned to any VIN ). Can you able to help me out on this issue?
The valve body is coded to the transmission. He bought it as a complete set so what he did is sufficient. If the valve body goes bad and you replace it then you will need to code the valve body to the transmission probably using the same software.
Wasn't the whole point to show programming a used transmission? You don't show literally any of it... You do a walk through on keys, and end the video...
![ตีสิบเดย์ [FULL] | คู่รักแซฟฟิก "หลิงหลิง - ออม" จากซีรีย์ "ใจซ่อนรัก"](http://i.ytimg.com/vi/zs8AfphGn2w/mqdefault.jpg)
![THE TOYS x NONT TANONT - ดอกไม้ที่รอฝน (spring) [Official MV]](http://i.ytimg.com/vi/pPa1d5cC8M4/mqdefault.jpg)
SAM GOOD TO FINALLY HEAR FROM YOU AGAIN , hope all is well and looking forward to many more learning experiences thanks for your time .
More to come!
Thanks. I dont use ODIS enough to find my way around and i didnt want to spend a bunch of time researching. this help.
Great video Sam, I’ve never done a Volkswagen or Audi programming using Otis yet so I would love a video of how to set it up. Keep up the good work
Coming soon!
SAM, always good information you share really appreciate ur time buy the way i could not hear you because the voice is to low please increase the volume and as always thanks for sharing been waiting long time for ur videos. cheeeeers
The Audi I had to adapt with ODIS required more key cycles in the test plan....Additionally, I found that the only key that will "work" or start the vehicle afterwards was the key or keys that were present during the process....any keys that are not there are worthless later and the vehicle will act as if you never programmed or adapted....my Audi was a 2013 A3....hope this helps 👍...so for future reference, have all keys present to avoid "potential" call backs later
That's a very good video. Do you know if a USED BCM2 module (main ecu of the immobilizer) can be adapted to the car with ODIS? Thanks a lot
Hi, and thank you for the information. As I understood you started with immo. but what about the next step concerning the transmission?
Sam you mentioned that there are other tools that this can be done with, could you share a link to the forum that you mentioned where they are discussing this sort of thing, I changed my transmission on an 09 A4 and would hate to take it to the stealer to get this done.
can the otis software be used to remove the component protection on a 2011 Audi A4 Radio and Ac controller
What is the deffrence between odis and odis engineering?
Hi, Im writing from México. Aré you able to share step by step programing of the mechateonic Unit for Audi 2016? Un México Is expensive, expensive, expensive. Can you help me?
Hi, I am trying to get more information on how to perform a TCU update, calling around the service shops in the area and they never can answer or call back. Looking at AliExpress ODIS interfaces... but how will I log in to retrieve the TCU update firmware/reflash? I have several questions as to how you obtained your setup and etc, thanks in advance if you can shed any light or help guide me in the right direction. I am not now to ECU reflashing, just VW ECU's haha.
THis job cannot be done with a stand alone ODIS. You need a subscription
Had no idea vcm2 would work,,, I have a mongoose Ford one,, would you know if that would work also,,, I do got a Audi im needing to sync the vins as the original ecm went toast,,
I do not know if the mongoose would work
Tool Hut USA aka The Car Flasher ... ok thanks for the info! And thanks again for the videos!!!
Hi did u use the same transmission?
And can u program it with different transmission code ?
I am pretty sure it was the same transmission. I did not see an option to change to a different configuration.
Hi friend I need your help
So, does this pretty much mean that the reprograming of the transmission is simply just a security protocol, adapting the new part to the ECU? Don't suppose you know if a different code trans can be programmed, my current is MKE 2011 and I would like to fit 2014 PWW?
It is 100% about security. Not sure you can swap part numbers
Codes have to match…you can’t swap.
Hi, nice video and nice and clean explanation. This’s the same procedure for Audi A4 because I have changed a used transmission?
Yes same thing
@@toolhutusaakathecarflasher3019 okay. I did online programming but it says the vehicle key is not OE it’s a Aftermarket key so the programming cannot be performed. Whether it’s ture? But vehicle was running with the same key for a long time. The massage popped up while programming ( Key not assigned to any VIN ). Can you able to help me out on this issue?
@@sainath8710 you should not have had to touch the keys. Just do transmission initialization
@@ToolHutUSA we did only the transmission initialisation then Why it’s saying key problem
Does the valve body have to be replace ?
This was a used transmission from the salvage yard. The Valve body is the one that came in the transmission
The valve body is coded to the transmission. He bought it as a complete set so what he did is sufficient. If the valve body goes bad and you replace it then you will need to code the valve body to the transmission probably using the same software.
Where are you located? can you do mine?
Detroit area.
Wasn't the whole point to show programming a used transmission? You don't show literally any of it... You do a walk through on keys, and end the video...
That is what is required on this vehicle