2011 lexus IS F, valley plate leak repair

แชร์
ฝัง
  • เผยแพร่เมื่อ 6 ก.ย. 2024

ความคิดเห็น • 252

  • @dawkrb
    @dawkrb 6 หลายเดือนก่อน +6

    Piece of added advice-The shop that did mine replaced the valley plate with a new one as they can warp. They also used a RTV sealant used on UPS trucks that is good for a million miles (so they say). I wouldn't want to use the same sealant that went bad unless Toyota has an improved version. I still can't figure out why they just didn't use a gasket. This was on a 2011 IS-F as well. And all the injector clips will need to be replaced. Great Video-thank You.

  • @gsheverything_2716
    @gsheverything_2716 4 ปีที่แล้ว +26

    Finally Finally, I mean finally someone did a VIDEO repair of VPL on these ISF, thank you for this VIDEO

    • @alltsab
      @alltsab  4 ปีที่แล้ว +14

      Not many on the road that why

    • @gsheverything_2716
      @gsheverything_2716 4 ปีที่แล้ว +8

      @@alltsab Yes you right about that

    • @jk_isf
      @jk_isf 2 ปีที่แล้ว

      @@alltsab do you do these on regular?

  • @tx4778
    @tx4778 4 ปีที่แล้ว +4

    Thank so much for this video I bought my ISF last year and I notice my heater would get cold when it’s at idle during the winter. I work at a Lexus dealership and my technician said it’s your valley plate and i saw forms saying $1000 to $2000 for just replacing the seal but I haven’t seen any major coolant leaks but I do check on it but again Thank You because you’re literally the only person that has made a video for this.

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      You welcome

  • @cr8tvt
    @cr8tvt 4 ปีที่แล้ว +10

    This is an awesome video. I actually watched the entire video twice. My Son’s ISF’s Valley plate is leaking. Heading to Fresno soon.

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      Thanks

  • @XBrandonLeeX765
    @XBrandonLeeX765 4 ปีที่แล้ว +6

    Thank you for filming this! I wish it was more detailed, but I understand. I really do appreciate your work & effort.

    • @alltsab
      @alltsab  4 ปีที่แล้ว +6

      I try to put more detail but some time waste a lot time to watch

  • @lester2392
    @lester2392 4 ปีที่แล้ว +2

    Probably the first and only complete video covering one of the two most common problems on the ISF (the other issue being a cracked manifold).
    Thank you so much for posting this!
    I had mine repaired at the dealership in 2018 and it would've been a $2500 dollar job but I had extended warranty.

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Wow that is very expensive. It only cost my friend $300 he is lucky.

    • @lester2392
      @lester2392 4 ปีที่แล้ว

      @@alltsab Is your friend in a mafia? I'd love to get a deal like that from Lexus. Hahaha!

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      @@lester2392 😄 close enough 😆 good friend got the best deal.

  • @hoarbaby
    @hoarbaby 4 ปีที่แล้ว +6

    Nice work man, when mine starts leaking I’m coming to you!

    • @alltsab
      @alltsab  4 ปีที่แล้ว +2

      Thanks

  • @natevillagomez4342
    @natevillagomez4342 3 ปีที่แล้ว +3

    Taking stuff off isn’t my problem, putting it back is. Great video btw!

    • @alltsab
      @alltsab  3 ปีที่แล้ว +1

      Thanks

  • @sameldj
    @sameldj 3 ปีที่แล้ว +2

    Thank you sooooo much. Doing this repair this weekend and now this video gives me all the confidence I needed. Looks pretty straight forward. Not many videos like this on our IS-F. Thank you once again.

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      U welcome

  • @motocross1550
    @motocross1550 2 ปีที่แล้ว +1

    that sigh at 2:03, rofl, that was my exact reaction to starting this job. excellent video

  • @vladimirzuraev565
    @vladimirzuraev565 9 หลายเดือนก่อน

    You’re a legend mate.
    That’s brilliant job, hard though. Appreciate much that you’ve shared this stuff with Lexus owners.
    My LS460 awaits this job to be done; roll sleeves up.

    • @alltsab
      @alltsab  9 หลายเดือนก่อน

      Thank you 😊 happy Thanksgiving

  • @Midwest..
    @Midwest.. 4 ปีที่แล้ว +3

    You're the best mechanic thank for VDO😎👍

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      You welcome don't forget to help subscribe to support me.

  • @ExclusiveTint-CarDetailing
    @ExclusiveTint-CarDetailing 4 ปีที่แล้ว +3

    Thank you for this I just found out mine is leaking as I was installing my oil air seperator and realised. If anyone else can make more detailed step by step videos soon will be good.

    • @alltsab
      @alltsab  4 ปีที่แล้ว +3

      Hope someone can do but I think no one will do it because not many of these car out there. Not just that it take too much time to film it.

    • @1OMEGA111
      @1OMEGA111 3 ปีที่แล้ว

      @@alltsab Lucky for you the 1UR-FSE has the same problem! I put mine back together today only to realize that the valley plate did not seal, coolant all over the ground. Not sure where I went wrong, I'm wondering if I accidentally over-torqued the bolts causing the FIPG to squish out too far..?
      I should have tested it prior... but It did only happen after the coolant system was under pressure.

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      @@1OMEGA111 I gave everyone warning about leak test before closing everything in my video. Check the 2 o-ring you may accidentally twist it while you install.

    • @1OMEGA111
      @1OMEGA111 3 ปีที่แล้ว

      ​@@alltsab Ah no, I found this video today while trying to find why it leaked. I should have tested it, but was under the impression that It would need to be leak tested while the engine was running. Though it did only seem to start leaking after it was under pressure... I Did not realize it was possible to test while the intake was off.
      I was thinking that as well, though I dipped the o-rings in coolant to act as something of a lubricant during install. So I dont think they'd be twisted, but maybe pushed out of the groove? Though the orings are my guess for the leak as the only issue I can think of with the plate would be that it was over-torqued, I set my torque wrench to 15ftlbs but could have tightened a few bolts a few ftlbs over, though I cant imagine the difference of a few ftlbs would have caused that much of a leak.

    • @1OMEGA111
      @1OMEGA111 2 ปีที่แล้ว

      @@stevekalesia3922 I pinched the oring on the large pipe that connects the plate to the pump. It got caught and rolled backwards when I put it in so it was just spewing coolant
      Replaced it and more carefully installed the plate, on a side-note, I just took it apart again for a different reason and the seal has held (I used permatex "the right stuff" rtv)

  • @ricksingh3671
    @ricksingh3671 2 ปีที่แล้ว +3

    Just a piece of advice, the fuel injectors will and can crack upon removal and installation. More on the driver side
    each injector is around 350 at the dealer (US) a rebuilt injector is a waste of time they will crack just plugging them in or trying to
    remove the pigtail. BE extremely careful, I have done a few the last one I did takes the cake. Under that intake is a motherload of heat that fries everything. The other part of this video I did not have to pull the starter wire I hung the harness over to the driver side with a tie.

    • @mechanickiwi4116
      @mechanickiwi4116 10 หลายเดือนก่อน

      You don't have to remove the injectors for this repair.

  • @Sessions1
    @Sessions1 ปีที่แล้ว

    Super helpful, working my ISF in two weeks once all parts are available

    • @alltsab
      @alltsab  ปีที่แล้ว +1

      Thanks

  • @whitefoxcoupe2024
    @whitefoxcoupe2024 4 ปีที่แล้ว +1

    Great video. I had mine done at the dealer. I can see why the car was gone for a week.

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      How much they charge you?

    • @alltsab
      @alltsab  4 ปีที่แล้ว +2

      @Isaac Chavez 800 still a lot but cheaper than 2k at the dealership.

  • @amgone75dm
    @amgone75dm ปีที่แล้ว

    Just a tip..the primary injector harness does not need to be disconnected. I just did this repair and you can zip tie the harness out of the way.

  • @ericgutierrez812
    @ericgutierrez812 3 ปีที่แล้ว +1

    Loved your video! I know some guys in Cali that might need the job done; so if you're up for and wanna get payed let me know, I'll be sending them your way good sir! God bless 🙌

  • @HumbledGod
    @HumbledGod 4 ปีที่แล้ว +2

    nice video clean explanations i see the camera work too 👍👍

  • @onlinesales-tm5xn
    @onlinesales-tm5xn 10 หลายเดือนก่อน

    Can you tell us what the part numbers were for o-rings and gaskets?
    My recomendation for you is to post those part numbers in your video description as well
    My 2nd recomendation is to set up accounts with Amazon, Walmart etc to do "drop shipping" account and add the link into your descriptionfor these parts this way you get a small percentage and people can just click link to go straight to part.
    You can do that with all your videos you use parts in. 😂
    Thank you so much My brother! GOD BE WITH YOU ALWAYS.

    • @alltsab
      @alltsab  10 หลายเดือนก่อน +1

      Thank you for the advice. Sometimes I'm not the one who buy the part so I don't have the part number.

  • @hcnco8752
    @hcnco8752 4 ปีที่แล้ว +3

    Amazing I love it. Well done.

  • @kibo5000F
    @kibo5000F 4 ปีที่แล้ว +1

    Nice to meet you,It was helpful.👍😊

  • @mckav2358
    @mckav2358 4 ปีที่แล้ว +3

    Look at all the plumbing you have to remove to get to the valley.
    What a minefield
    Ive heard this V8 has a reputation for leaking in the valley
    How long did the job take i bet 8-10 hours

  • @clarionguy7712
    @clarionguy7712 4 ปีที่แล้ว +1

    Very nice video. Thanks a lot!

  • @bajafishin
    @bajafishin 4 ปีที่แล้ว

    Thank you. Always love your videos. Awesome info and help me learned so much. Please continue to make more videos.

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Thanks

  • @aminort2
    @aminort2 3 ปีที่แล้ว +1

    @AllTsab I just liked and subscribed to you! First time seeing a video on the ISF Valley Plate Leak fix.
    I wish I lived in Cali, because when the inevitable time comes for my repair, I'm gonna be a grown ass man crying as I do it :o

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      Thank you so much for helping subscribe. Hopefully your car don't have this issue.

    • @aminort2
      @aminort2 3 ปีที่แล้ว

      @@alltsab I'm currently at 164k now on my 2008 and am fine for now, but this VPL issue appears to be an inevitable failure for all of these engines :(

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      @@aminort2 I know it's poor design for most toyota that have V engine.

    • @ericgutierrez812
      @ericgutierrez812 3 ปีที่แล้ว

      @@aminort2 it doesn't happen to all of them man. I know a guy that has roughly 250k miles on his 08 and still sign of it.

  • @assassin40oz
    @assassin40oz 2 ปีที่แล้ว

    Thank you so much for sharing! Outstanding work!

    • @alltsab
      @alltsab  2 ปีที่แล้ว

      You welcome buddy very appreciated 🙂👍

  • @jakeestrada1239
    @jakeestrada1239 2 ปีที่แล้ว

    I think I was applying silicone wrong, took of manifold off 3rd time now. Gunna try silicone way you did it. This is for my Tundra, thank you

    • @alltsab
      @alltsab  2 ปีที่แล้ว

      Mistake is no big deal in your own car it's just a learning process and that will the best teacher you ever learn from it.

    • @jakeestrada1239
      @jakeestrada1239 2 ปีที่แล้ว +1

      @@alltsab 100 % agree
      I take of intake manifold in like 15 minutes now lol.
      Thank you :)

    • @mechanickiwi4116
      @mechanickiwi4116 ปีที่แล้ว +1

      The heat exchanger(top piece) can sometimes develop tiny cracks, so even though you sealed it properly, it still leaks, maybe better to buy new heat exchanger.

    • @jakeestrada1239
      @jakeestrada1239 ปีที่แล้ว +1

      @ Actually ended up doing that!

  • @feriananggi
    @feriananggi 3 ปีที่แล้ว

    thanks dude, very helpful video for my knock sensor repair wich the same way to remove the intake manifold

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      You welcome buddy

  • @Foxtrot2312
    @Foxtrot2312 3 ปีที่แล้ว +11

    Such a shame that gorgeous intake manifold is hidden below all those wire looms.

  • @art.vrodriguez530
    @art.vrodriguez530 3 ปีที่แล้ว

    Good and excellent video... follow you from Mexico Amigo

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      Thank you amigo

  • @thanavatvichetvipattana646
    @thanavatvichetvipattana646 4 ปีที่แล้ว +1

    amazing work .. Love the content !!

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Thank

  • @mckav2358
    @mckav2358 4 ปีที่แล้ว +2

    This leak is an issue on many is f's not just the odd one or two
    The gasket fails because it deteriorates with age. It is an inferior material not able to stand up to heat and pressure.
    This should be a warranty issue

    • @ericgutierrez812
      @ericgutierrez812 3 ปีที่แล้ว +1

      It is/was warranty covered issue BUT it should be a lifetime warranty coverage type of issue because it is a flaw from the manufacturer on these beauty's.

  • @OctaneSlain
    @OctaneSlain 8 หลายเดือนก่อน

    Well, I was contemplating buying one of these cars, but what a nightmare of vacuum lines and electrical spaghetti smothering up the intake manifold. Too excessive. Valve cover gaskets look like they would be a nightmare too. What a bummer.

  • @SlowWhip
    @SlowWhip 4 ปีที่แล้ว +1

    Amazing job 👍🏽

  • @waqasazmat81
    @waqasazmat81 8 หลายเดือนก่อน

    thanks for posting this!

    • @alltsab
      @alltsab  8 หลายเดือนก่อน

      You welcome

  • @nathanlopez5667
    @nathanlopez5667 4 ปีที่แล้ว +2

    I think mine must have been replaced at some point my isf has over 215,000 miles

  • @tubejorrit
    @tubejorrit 2 ปีที่แล้ว

    Thanks for this video! I'm looking for a 2nd hand IS-F, how can I see if the valley plate is leaking before buying the car?

    • @alltsab
      @alltsab  2 ปีที่แล้ว +1

      Jack the car up you can see signs of leaking mark where the transmission and engine connected. If you buy this car just expecting the problem a head.

  • @mikepgon63
    @mikepgon63 หลายเดือนก่อน

    Did you use any kind of tool to pull starter connector? It is very tight in there and my hands can fit to pull connector out

    • @alltsab
      @alltsab  หลายเดือนก่อน

      @@mikepgon63 small flat screw driver

    • @mikepgon63
      @mikepgon63 27 วันที่ผ่านมา

      @@alltsab I’m trying to just not enough space to wiggle around.

  • @2kscmax
    @2kscmax 4 ปีที่แล้ว +1

    At 17:13 you stopped the video when you were about to install the valley plate , can you explain to me how you got it in that easy? What did you move at the firewall? The reason I’m asking you as it’s very tight space at the fire wall. I removed the wire harness, and the fuel line hose and still had difficulty aligning the plate with out touching the sealant
    Thanks 🙏

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Lube the o-ring little bit and play around little bit should slide right in. You must take the stud in the alley out to be easy fit in.

    • @2kscmax
      @2kscmax 4 ปีที่แล้ว +2

      All Tsab yes I already did take the studs out , lubed the o rings, and removed the fuel line ( firewall) and installed it without disturbing the sealant. Thanks

  • @taquanjoe718
    @taquanjoe718 4 หลายเดือนก่อน +1

    Already u have a headache..😂😂stop crying get it done im watching u

  • @marineyacht
    @marineyacht 2 ปีที่แล้ว

    One quick question. The black foam piece on top of the valley plate is important to reinstall ?
    I need to change the fuel rail pressure sensor and because of that black foam I can see it not even with an endoscopic camera. Am sure am not placing back.

  • @navaho5430
    @navaho5430 3 ปีที่แล้ว +2

    I commend you for doing this HARD JOB, i am a mechanic and i dread doing my 2011 ISF. THANK YOU FOR POSTING THIS VIDEO. Have you done PPE headers on the ISF " I'M SURE YOU COULD" all the best to you and your family cheers from OZ

    • @alltsab
      @alltsab  3 ปีที่แล้ว +1

      Thanks buddy one of this day if I run across one that need head job I will do.

    • @navaho5430
      @navaho5430 3 ปีที่แล้ว +1

      @@alltsab Are you a mechanic, because you seemed to know exactly what your doing, how many IFS valley plates have you done, kudos to you, pitty i live in OZ but maybe you can come over cheers from OZ.

    • @alltsab
      @alltsab  3 ปีที่แล้ว +2

      @@navaho5430 i haven't done many isf but almost every toyota engine very similar

    • @mechanickiwi4116
      @mechanickiwi4116 10 หลายเดือนก่อน

      It's not a hard repair, just time consuming. You dont need to spend the $ on the toyota fipg sealant, just use permaseal "the right stuff"

  • @SouthernCrossMotors
    @SouthernCrossMotors 2 ปีที่แล้ว +1

    Wow...bit of a mission, but take your time and do it yourself rather than $1,000 labour at the dealership.

  • @KVIZZZZLE
    @KVIZZZZLE 4 หลายเดือนก่อน +1

    gotta do my direct injection soon :(

  • @user-qx4yl5nd6u
    @user-qx4yl5nd6u 8 หลายเดือนก่อน

    My isF has bubbles in the coolant tank but there’s no overheat u think it’s the valley plate?

  • @jrcuna5432
    @jrcuna5432 2 ปีที่แล้ว

    Sir Iam in the center valley to and my Lexus ls460 is leaking coolant From the valley plate are u available thanks.

  • @computermech
    @computermech 3 ปีที่แล้ว

    All Tsab you need to move to Toronto, Canada. There seem to be a lack of good mechanics.

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      Sure I like Canada 🇨🇦

  • @xiongbeezo1983
    @xiongbeezo1983 4 ปีที่แล้ว +2

    Where do you live bro, and how much do you charge for this? By the way The Sounders is the best band ever.

    • @alltsab
      @alltsab  4 ปีที่แล้ว +2

      Central cali 😆

  • @sgbabyflex
    @sgbabyflex 7 หลายเดือนก่อน

    Hello. If you don't smell antifreeze then you don't have this issue correct ? I just want to do preventative maintenance on my ls460 and heard this is common. Thank you so much

    • @alltsab
      @alltsab  7 หลายเดือนก่อน

      Not really if still still leak you probably don't smell it

  • @ninja5ever1984
    @ninja5ever1984 3 ปีที่แล้ว

    Great job bro, you must be Hmong with the Sounders song lol

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      Lol😁😁

  • @theah781
    @theah781 2 ปีที่แล้ว

    Nice video. I don't have a valley plate on my 97 es300 but nice to know anyway

  • @SNORKYMEDIA
    @SNORKYMEDIA 3 ปีที่แล้ว

    when you are putting the top back on at 16:52 it looks like there is a rubber gasket on there too not just silicon??? where is that from please?

    • @alltsab
      @alltsab  3 ปีที่แล้ว +1

      All silicone no gasket

  • @GreatSax1
    @GreatSax1 6 หลายเดือนก่อน

    Should I be gentle with the acceleration once the repair has been made?

    • @alltsab
      @alltsab  6 หลายเดือนก่อน

      No you can drive as normal

  • @imrekecskes5287
    @imrekecskes5287 3 ปีที่แล้ว

    Hi,
    How much torque do you tighten the Valley Plate?
    15nm or 21nm?

  • @ukaszsl.6242
    @ukaszsl.6242 7 หลายเดือนก่อน

    Good job, have you done it in lexus RCF? Any vid?

    • @alltsab
      @alltsab  7 หลายเดือนก่อน

      Not yet I don't have anyone I know own one yet but I will definitely if I have an opportunity to work on one I will record and post it. However, all lexus should be very similar to each other.

  • @Mr.Beastforpresident
    @Mr.Beastforpresident 4 ปีที่แล้ว

    Friend what do you film with? Phone? If so what model phone? It’s clear with great audio

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Hero 3 silver cheap go pro

    • @Mr.Beastforpresident
      @Mr.Beastforpresident 4 ปีที่แล้ว

      All Tsab I’ve been wanting to make videos. But I can’t find a good simple video on how to make them. So you simply record on a Go-Pro then pause it when necessary when moving and mounting it into a car or you just leave it on and edit walking around with it out?
      What editing software you use?
      I’ve thought about just using my phone but I don’t think it’s possible for long detailed videos, at least from what I see most nearly all use a Go Pro.
      Is a Labtop or computer a must?
      Reason I ask is I disconnected my land internet in favor or Unlimited Cell data and I’ve been doing everything on my phone for years. Even Powerselling on Ebay, 1,700+ feedback all from my IPhone.

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      @@Mr.Beastforpresident I edit in my computer and used my phone to upload to the TH-cam. You can used any free video editing to edit. Use the most simple and friendly editing tool so you won't frustrate. The reason I saying it because you don't need to do a lot graphic fancy editing. If you getting better with the simple one then you can try to move on to the higher end one. By the way did you help subscribe to my channel yet? Please help subscribe and share too ok thanks.

    • @Mr.Beastforpresident
      @Mr.Beastforpresident 4 ปีที่แล้ว +1

      All Tsab Yes, I subscribed about a month ago. I have YT Premium, I watch more YT than tv.

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      @@Mr.Beastforpresident thank

  • @ferrari250lm
    @ferrari250lm 3 ปีที่แล้ว

    He didn't even bother to cover the intake ports while he was working, lol!!!

    • @hoarbaby
      @hoarbaby ปีที่แล้ว +1

      Thug life

  • @michaelvang3034
    @michaelvang3034 8 หลายเดือนก่อน

    What’s up brother Tsab, would you happen to remember the part # for the 2 O-ring gaskets? I’m about to repair my leak as well.

    • @alltsab
      @alltsab  8 หลายเดือนก่อน +1

      I don't have the part number but you can call lexus

    • @michaelvang3034
      @michaelvang3034 8 หลายเดือนก่อน

      Thanks, I was able to find them. How much do you charge for this job?

  • @igjonathan.s2k803
    @igjonathan.s2k803 ปีที่แล้ว

    Where are you located I need this done on my ISF

  • @JUUPAPE
    @JUUPAPE ปีที่แล้ว

    What parts do you need when doing this job? Besides the sealant ofc😂

    • @alltsab
      @alltsab  ปีที่แล้ว +1

      That's all you need

  • @PANNYMAN
    @PANNYMAN 4 ปีที่แล้ว

    Great video!! part number for the o-rings?

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      I don't have the part number

    • @pimpin94gsr
      @pimpin94gsr 4 ปีที่แล้ว +2

      O-Ring part # 9676135035
      parts.lexusofqueens.com/p/Lexus_2008_IS-F-50L-AT/Engine-Coolant-Pipe-O-Ring/62977035/9676135035.html

  • @leonmok6283
    @leonmok6283 ปีที่แล้ว

    Hi, how long do you expect the fix to last before it leaks again? or do you think the fix is permanent?

    • @alltsab
      @alltsab  ปีที่แล้ว +1

      No clue because poor design of it. I can say if you prepared very good as I do it should last minimum of 10 years

  • @mikevtvan2787
    @mikevtvan2787 3 ปีที่แล้ว

    How long it take u to do this lexus dealer say 8h labor cost me like 1,585 ....

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      Yes about 6 to 8 hours job

  • @mechanickiwi4116
    @mechanickiwi4116 ปีที่แล้ว

    Is there a torque for the knock sensor bolts?

    • @alltsab
      @alltsab  ปีที่แล้ว

      Yes but almost people hand tight it

  • @wernersoto5371
    @wernersoto5371 2 ปีที่แล้ว

    I have a 2012 with a coolant leaking valley plate, are you in southern California?
    Can you reseal my car?

    • @alltsab
      @alltsab  2 ปีที่แล้ว

      Is not that hard to take the intake out. The only thing that is to the sensor behind the starter that all. You can do it buddy. I'm in central ca.

    • @MrGeekyMoDz
      @MrGeekyMoDz 26 วันที่ผ่านมา

      @@alltsabhi how can I get in contact with you, I’d like to have this done and very close to central cal

  • @JacobyAldrich
    @JacobyAldrich 2 ปีที่แล้ว

    Did you let the silicone fully cure before testing it with the intake manifold off?

    • @alltsab
      @alltsab  2 ปีที่แล้ว

      Yes

    • @JacobyAldrich
      @JacobyAldrich 2 ปีที่แล้ว

      @@alltsab okay thank you! Going to tackle this job in 2 days and want to just make sure I fully understand, great video

    • @alltsab
      @alltsab  2 ปีที่แล้ว +1

      @@JacobyAldrich good luck to you my friend ❤

  • @christophermagee9079
    @christophermagee9079 3 ปีที่แล้ว

    Hi I recently did a valley plate job on my lexus ls460 and I have this problem when I put it all back together any idea whats causing this

  • @Mr.Beastforpresident
    @Mr.Beastforpresident 4 ปีที่แล้ว

    Friend Carb cleaner will swell up O-rings. Spray carb cleaner on the old O-rings and see for yourself

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      You absolutely right but you have to wait for it dry out first. I used Carb cleaner is dry fast so I don't have to wait long. Thanks for a great advice.

    • @Mr.Beastforpresident
      @Mr.Beastforpresident 4 ปีที่แล้ว

      All Tsab Why not Orielly brake cleaner on a rag? I find Orielly brake cleaner works better than any other brand I’ve tried including CRC
      Also, I would have used Permatex Ultrablack Gasket Maker ( pictured below ) instead of the clear silicone again, the clear silicone failed once. The Ultrablack is extremely tough. BUT I could be wrong, you may know something I don’t.
      Please correct me if I’m wrong. I have 20+ years experience BUT there’s many things I don’t know. Still learning everyday.
      www.permatex.com/products/gasketing/ultra-series-gasket-makers/permatex-ultra-black-maximum-oil-resistance-rtv-silicone-gasket-maker-4/

    • @Mr.Beastforpresident
      @Mr.Beastforpresident 4 ปีที่แล้ว +1

      All Tsab Great Videos by the way 👍👍👍 great channel. You do quality work done right. You’re good at what you do, most other mechanics and shops are half@ss, use cheap non-OEM quality parts and don’t believe in Torque Wrenches

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      @@Mr.Beastforpresident ultra black is what I always been used too thanks.

  • @artccie
    @artccie 3 ปีที่แล้ว

    Can you please do a ls 460 Valley Plate disassembly video?

    • @alltsab
      @alltsab  3 ปีที่แล้ว +1

      460 Should be similar with 500 because the 300 also similar. I think the 460 will easier not that pack like the ISF

    • @alltsab
      @alltsab  3 ปีที่แล้ว +1

      I don't have a vehicle atm but in the future I do one if available.

    • @artccie
      @artccie 3 ปีที่แล้ว +1

      Kumusta! The LS 460 has the same wiring loom hornets nest above the intake manifold. The intake manifold is plastic though and should be lighter....you can make a killing doing this gasket service on late model LS 460 which is prone to leak. Thanks again!

    • @rzqdzn
      @rzqdzn 2 ปีที่แล้ว +1

      I would replace that knock sensor harness as well. Every valley plate I’ve done on the ls460 has needed the harness replaced do to brittle connectors.

    • @theah781
      @theah781 2 ปีที่แล้ว

      @@rzqdzn might as well while it's all open. That hose too

  • @duhboi6516
    @duhboi6516 4 ปีที่แล้ว

    The silicone that you used, is that safe for coolant?

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Toyota made this silicone for this purpose so I will say yes 100% safe for coolant.

  • @singhsarabjit
    @singhsarabjit 11 หลายเดือนก่อน

    Is it same for 2011 Lexus GX460 4.6L? Thanks G

    • @alltsab
      @alltsab  11 หลายเดือนก่อน

      No but similar to most toyota and lexus v6 and v8

    • @singhsarabjit
      @singhsarabjit 11 หลายเดือนก่อน +1

      @@alltsabThank you very much!!!

  • @VICTORLopez-gi2ec
    @VICTORLopez-gi2ec 2 ปีที่แล้ว

    Do you know number for gasket on metal tube

    • @alltsab
      @alltsab  2 ปีที่แล้ว

      Sorry no

  • @jaysil7083
    @jaysil7083 ปีที่แล้ว

    Question- Did you drain the coolant from the radiator before you start ? TIA

    • @alltsab
      @alltsab  ปีที่แล้ว

      Yes

    • @jaysil7083
      @jaysil7083 ปีที่แล้ว

      And the block too or just the radiator?

    • @alltsab
      @alltsab  ปีที่แล้ว

      @@jaysil7083 just radiator

    • @jaysil7083
      @jaysil7083 ปีที่แล้ว +1

      Thanks sir! Appreciate you for answering Will be doing the Job in the next few days

    • @alltsab
      @alltsab  ปีที่แล้ว

      @@jaysil7083 you welcome buddy please help support subscribe to my channel okay thanks

  • @ukaszsl.6242
    @ukaszsl.6242 3 ปีที่แล้ว

    Heard that pink toyota coolant causes leaks. Red toyota coolat is ok. Is that true ?

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      No not true. Pink is mix 50/50 red is need to mix that all

    • @ukaszsl.6242
      @ukaszsl.6242 3 ปีที่แล้ว

      @@alltsab you are talking about pink-super long life and Red -longlife? Which one is recomended for isF /rcf?

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      @@ukaszsl.6242 pink is good

    • @ukaszsl.6242
      @ukaszsl.6242 3 ปีที่แล้ว

      @@alltsabone Man on TH-cam says that those fluids are different fluids( different acids ) bullets Garage

  • @FPS515
    @FPS515 3 ปีที่แล้ว

    How did you manage to get the starter signal wire off? What did you use?

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      Very difficult to get it off i used ring plier

    • @djkor
      @djkor 3 ปีที่แล้ว

      I just started tacking this one and the only thing now preventing me moving the whole harness to the side is removing that one connector. I honestly don't know how he managed to do it. There is like no clear access to the damn thing.

    • @zellerized
      @zellerized 6 หลายเดือนก่อน

      Awesome mechanic

  • @VuNguyen-sg3uo
    @VuNguyen-sg3uo 3 ปีที่แล้ว

    you said you used water to check if it was leaking after you had replaced it. How do you drain it all afterwards?

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      I mean coolant not regular water. You don't need to drain it out because it's coolant already.

    • @VuNguyen-sg3uo
      @VuNguyen-sg3uo 3 ปีที่แล้ว

      Ok because I'm doing the valley plate now and after I let it cure, I filled it up with coolant and it always leaks so I'm trying to see if there's another way to test it out. I'm tired of buying bottles of coolant at a time lol

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      @@VuNguyen-sg3uo where it leaking from ? The valley plate or the tube o-ring. Make sure no leak before cover everything up. Good luck buddy

    • @VuNguyen-sg3uo
      @VuNguyen-sg3uo 3 ปีที่แล้ว

      It was leaking from the o ring and I got new ones so I'm going to keep trying until no more leak lol

    • @alltsab
      @alltsab  3 ปีที่แล้ว +1

      @@VuNguyen-sg3uo ok maybe when you insert it twist the o-ring that why it leak put some silicone in to suplicate it will go smoothly

  • @Jedi_Luke
    @Jedi_Luke 2 ปีที่แล้ว

    Damn I wanted an ISF but after seeing this I think I'll stick with the 350 lol

  • @joelandersonphoto
    @joelandersonphoto 4 ปีที่แล้ว +1

    So the valley is cooled?

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Yed

    • @joelandersonphoto
      @joelandersonphoto 4 ปีที่แล้ว +1

      That motor looks like a disaster of overcomplication, and the wire harness is exposed to too much heat

    • @d1sturb3d119
      @d1sturb3d119 4 ปีที่แล้ว +2

      @@joelandersonphoto And yet folks have over 300k miles and are still pushing these cars. Not overcomplication. That is most motors today. Ironically enough despite all of that it's a pretty amazing engine with little issues if any.

  • @fl3cko91
    @fl3cko91 4 ปีที่แล้ว

    New subscriber, hello my friend where can i find you so you can repair my isf lexus.

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      Thanks for the subscribe. I'm in central california my friend.

  • @gerardolopez3838
    @gerardolopez3838 2 ปีที่แล้ว

    How did you take out the starter connector?

    • @alltsab
      @alltsab  2 ปีที่แล้ว

      Very hard, my hand small so I reached in the back to pull it out. As shown in the video I used a little pick to pry the clip then pull it out. Take me a long time on that clip

    • @gerardolopez3838
      @gerardolopez3838 2 ปีที่แล้ว

      Is the clip release tab facing down or up?

  • @Sessions1
    @Sessions1 3 ปีที่แล้ว

    What area are you in? I’m in need of a vp repair :/

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      Central California

  • @Mabeylater293
    @Mabeylater293 5 หลายเดือนก่อน

    Will it leak again?

    • @alltsab
      @alltsab  5 หลายเดือนก่อน

      Toyota never last forever so I think the way this car design definitely soon hit 100k or more it will leak again.

  • @davpart7723
    @davpart7723 3 ปีที่แล้ว +1

    Can you fix mine??

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      I made this video for you to fix your

  • @heccov2270
    @heccov2270 3 ปีที่แล้ว

    Whats the cost for a job like this

    • @alltsab
      @alltsab  3 ปีที่แล้ว +1

      For me a case of corona, dealer in the thousands

  • @LunatrixEX
    @LunatrixEX 4 ปีที่แล้ว

    How long did this actually take you to do? 1 day 2 days 3 days

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      2 hours

    • @LunatrixEX
      @LunatrixEX 4 ปีที่แล้ว +5

      @@alltsab You are a madman...and a mastermind. wish i had a mechanic like you around!

    • @hoarbaby
      @hoarbaby 4 ปีที่แล้ว

      Joseph A. Lololol totally

  • @abz520
    @abz520 ปีที่แล้ว

    Anyone fix this with radiator stop leak?

    • @alltsab
      @alltsab  ปีที่แล้ว +2

      In my opinion you have a nice car don't used those garbage stop leak it will create cluster problems to your system. It will clog up your radiator and heater core.

  • @josegonzales8445
    @josegonzales8445 3 ปีที่แล้ว

    What area code you from??

  • @danielreyes229
    @danielreyes229 4 ปีที่แล้ว +1

    Are you located in California?

    • @topflight5592
      @topflight5592 4 ปีที่แล้ว

      Yeah this dudes in Fresno

    • @MrGeekyMoDz
      @MrGeekyMoDz 26 วันที่ผ่านมา

      @@topflight5592what’s his address?

  • @melissadinh3869
    @melissadinh3869 4 ปีที่แล้ว

    Is this the same for a gx460?

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      I will say similar to each other.

  • @BasedSwaghoe
    @BasedSwaghoe 4 ปีที่แล้ว

    How much would you charge to do my valley plate on Ls460, beers on me (:

    • @BasedSwaghoe
      @BasedSwaghoe 4 ปีที่แล้ว

      I’m in norcal

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      I did my friend car he just buy me lunch only. Lol

    • @BasedSwaghoe
      @BasedSwaghoe 4 ปีที่แล้ว

      Hmmm I’ll keep that in mind, right now I thought I had a leak refilled resovoir 2 days no leak. Might check water pump first if coolant goes down

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      @@BasedSwaghoe check your radiator tank beside the reservoir. Sometime the reservoir have coolant but tank is low in coolant.

  • @divadb8
    @divadb8 3 ปีที่แล้ว

    What would be the price for this ? Might have to make the drive up to u :)

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      😆 lol could be in the thousands at the dealer

    • @divadb8
      @divadb8 3 ปีที่แล้ว

      @@alltsab but for you to do your magic

    • @alltsab
      @alltsab  3 ปีที่แล้ว +1

      @@divadb8my magic less than a case of corona lol

    • @divadb8
      @divadb8 3 ปีที่แล้ว +1

      @@alltsab whaat?? I got 5 cases for u then lol

  • @julianquijano5312
    @julianquijano5312 4 ปีที่แล้ว

    Would this be the same on a 2008 ls 460 ?

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Similar to each other. Toyota build their car not so much difference.

    • @julianquijano5312
      @julianquijano5312 4 ปีที่แล้ว

      All Tsab thanks man great video 👍

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      @@julianquijano5312 help subscribe for me ok

  • @djardy07
    @djardy07 4 ปีที่แล้ว +4

    Not f-sport it’s an F

  • @fudo5594
    @fudo5594 4 ปีที่แล้ว

    Hey, you're Hmoob! Where are you from?

    • @topflight5592
      @topflight5592 4 ปีที่แล้ว

      This dude is from Fresno I've seen him around town

  • @colonluis9441
    @colonluis9441 4 ปีที่แล้ว

    How much does a job like this cost?

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      If Lexus work for you it could be 1500. People you know could be 300 to 500

    • @colonluis9441
      @colonluis9441 4 ปีที่แล้ว +1

      @@alltsab ok thanks

  • @mckav2358
    @mckav2358 4 ปีที่แล้ว

    Om shocked to learn that they used silicone to seal instead of a gasket. That is a real disapointment. These cars cost big bucks & you think youre buying something thats not going to need this type of repair.
    NOT GOOD ENOUGH toyota!!!

  • @hokagev7957
    @hokagev7957 4 ปีที่แล้ว

    Hi Are you from Fresno?

    • @alltsab
      @alltsab  4 ปีที่แล้ว +1

      Yog kawg

    • @hokagev7957
      @hokagev7957 4 ปีที่แล้ว

      @@alltsab kuv muaj in lub Lexus ISF thaib koj puas kas check kuv Lexus for qhov valley plate leak?

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Tau kawg

    • @alltsab
      @alltsab  4 ปีที่แล้ว

      Muab koj tus xov tooj kuv mam hu koj

    • @hokagev7957
      @hokagev7957 4 ปีที่แล้ว

      @@alltsab muaj koj tus email rau kuv kuv mas email koj kuv tus xov tooj

  • @lv204
    @lv204 3 ปีที่แล้ว

    How do i get in touch with you? Would like to pay you to fix this leak on my car. Located in Sacramento but would be willing to come to you. Thanks

    • @alltsab
      @alltsab  3 ปีที่แล้ว

      Go to your local shop they can fix it for you is not that expensive.

    • @danielestrada1995
      @danielestrada1995 3 ปีที่แล้ว +1

      Check out Red Sun, they’ve done it for dudes in Sacramento area for good price

    • @MrGeekyMoDz
      @MrGeekyMoDz 26 วันที่ผ่านมา

      @@danielestrada1995where can I find this red sun?

  • @joelandersonphoto
    @joelandersonphoto 4 ปีที่แล้ว +1

    That looks like a poorly designed motor, overly complex, and the wire harness is likely exposed to too much heat, yowza, now I see why they say stay away from Lexus v8’s

    • @hoarbaby
      @hoarbaby 4 ปีที่แล้ว

      joelandersonphoto jfl

    • @danielestrada1995
      @danielestrada1995 3 ปีที่แล้ว

      Literally the only recurring issue people are having with these cars that affect all years are the valley plate leak, sticky dash and exhaust manifold crack. The sticky dash is covered through Lexus so just take it in to the dealer and they replace the dash and panels if they’re bad but Thats pretty much it