Hey, Great video and decided to purchase two of these to replace typ. motion sensors. My problem now is that they both detect the ceiling fans. During your video you mentioned that they can detect "human" presence, how can I keep these sensors from detecting the ceiling fans?
My guess is the "Chip set" is LD2410-P module from Hi-Link (HLK-LD2410-P) from the bottom of the unit. It's one of the first of the 24GHz sensors (super cheap). What makes it special is the zigbee interface. Wouldn't it be nice if there was a zigbee IDE (like Esphome) which would allow a DIY'er to make this for < $10.
Great video as I was looking to replace a couple of my Aliexpress Tuya presence sensors because these were constantly sending information to my Z2M that is causing collisions and caused instability on my other zigbee devices. Were you able to check how noisy this particular sensor is to your network? Would really appreciate it if you get the chance!
@@koneero For me I noticed that my Ikea blinds was slow to respond (remote and google home commands) like 5 seconds delay. As soon as I removed my Tuya presence sensors, I get almost instant. So I never returned these on my network, real waste of money. Was hoping to have a better replacement.
Hi great video. I have this sensor with zigbee2mqtt natively, but i think i have a issue...i can see the iluminance value, but i can't use as entity in automations. Do you know how to solve this?? Thanks, Best regards
Sonoff has a new one that's $15 right now. It's not as precise as some, the Aqara for instance can be set up to trigger on just areas of a room, not just the entire room. Otherwise very similar.
Awesome walkthrough🙂 Do you know if it can be bind directly to a group? Asking as I have some issues figuring out which clusters to check... Just curious, why do you trigger a state and not a device and also in the action you trigger a service and not a device group? I just installed a Tuya human presence sensor identified as TS0225. I did not add any script and it still exposes the same...so I guess I'm good to go right? 🙂
HI great video. I am having some trouble with mine. It added to Z2MQTT in HA but is says that it is unsupported device. I look at mine compared to the one you have in the video and it is identical. Not sure what I could be doing wrong. Any help would be appreciated.
Now linptech has three versions of the human presence sensor xiaomi ble mesh version, requires xiaomi ble mesh gateway tuya zigbee version, requires a tuya zigbee hub tuya wifi version, no hub required these 3 version all have same appearance,but with different firmware
Linptech Labs data: 180° range detection distance is: 10ft (3meter) 140° range detection distance is: 17ft (5meter) 60° range detection distance is: 20ft (6meter) Therefore, the detection distance depends on the angular range.
Proper crap design. I'm yet to see a manufacturer design a fault less design or a device that just works without issue. Even the FP2 is a piss poor design, ridiculously overpriced and it's software is buggy as hell
Hey, Great video and decided to purchase two of these to replace typ. motion sensors. My problem now is that they both detect the ceiling fans. During your video you mentioned that they can detect "human" presence, how can I keep these sensors from detecting the ceiling fans?
My guess is the "Chip set" is LD2410-P module from Hi-Link (HLK-LD2410-P) from the bottom of the unit. It's one of the first of the 24GHz sensors (super cheap). What makes it special is the zigbee interface. Wouldn't it be nice if there was a zigbee IDE (like Esphome) which would allow a DIY'er to make this for < $10.
There are things for diy zigbee
$36 isn't cheap. The Tuya zigbee ZY-M100 is way cheaper. Not even to mention the Sonoff one.
cheaper than the Aqara one
It's definitely prettier, but also about 50% more than the Tuya equivalent, which is fully supported with Z2M. Worth it?
Great video as I was looking to replace a couple of my Aliexpress Tuya presence sensors because these were constantly sending information to my Z2M that is causing collisions and caused instability on my other zigbee devices.
Were you able to check how noisy this particular sensor is to your network? Would really appreciate it if you get the chance!
This intrests me as well. Tuya mmwave-sensors over zigbee are extremely noisy and this, if they behave nicely, would be great replacements.
@@koneero For me I noticed that my Ikea blinds was slow to respond (remote and google home commands) like 5 seconds delay. As soon as I removed my Tuya presence sensors, I get almost instant. So I never returned these on my network, real waste of money. Was hoping to have a better replacement.
I have two of these Linptec sensors and three of the Zemismart Energy Monitor SE1. Monitor from MQTT Explorer, SE1 are more nosier than Linptec.
Hi great video.
I have this sensor with zigbee2mqtt natively, but i think i have a issue...i can see the iluminance value, but i can't use as entity in automations. Do you know how to solve this??
Thanks,
Best regards
Sonoff has a new one that's $15 right now. It's not as precise as some, the Aqara for instance can be set up to trigger on just areas of a room, not just the entire room. Otherwise very similar.
How high can you place them on a wall? I want to place it next to my cameras.
Awesome walkthrough🙂
Do you know if it can be bind directly to a group? Asking as I have some issues figuring out which clusters to check...
Just curious, why do you trigger a state and not a device and also in the action you trigger a service and not a device group?
I just installed a Tuya human presence sensor identified as TS0225. I did not add any script and it still exposes the same...so I guess I'm good to go right? 🙂
Lowcost?
I keep hearing you say "M-M wave". Is it not supposed to be pronounced millimeter wave as in the RF wavelength used by the radar sensor?
HI great video. I am having some trouble with mine. It added to Z2MQTT in HA but is says that it is unsupported device. I look at mine compared to the one you have in the video and it is identical. Not sure what I could be doing wrong. Any help would be appreciated.
upgrade to the latest version of z2m and it becomes a supported device.
CAN I HAVE IT TURN ON A AIR PURIFIER AND TURN OFF WHEN SOMEONE WALKS OUT THE ROOM?
U doxed ur self at 22:21 with amazon....
Thanks for this video but it is seems this mijia linpech device is different from the one I have mine is Xiaomi
Now linptech has three versions of the human presence sensor
xiaomi ble mesh version, requires xiaomi ble mesh gateway
tuya zigbee version, requires a tuya zigbee hub
tuya wifi version, no hub required
these 3 version all have same appearance,but with different firmware
@@付俊张 Thanks I figured this I bought the Xiaomi BLE version not realising but since I got Zigbee version they all works fine with Homeassistant
Nice find, looks good but doesn’t beat the new Sonoff SNZB-06P. 14.90 , dang…
Why doesn't it beat it appart for the Price ?
If the range on this device is about 6 ft. to me that's useless. Should be about 16 ft min.
Mine is good up to 6 meters.
Linptech Labs data:
180° range detection distance is: 10ft (3meter)
140° range detection distance is: 17ft (5meter)
60° range detection distance is: 20ft (6meter)
Therefore, the detection distance depends on the angular range.
unfortunate name
Proper crap design. I'm yet to see a manufacturer design a fault less design or a device that just works without issue. Even the FP2 is a piss poor design, ridiculously overpriced and it's software is buggy as hell