I absolutely love how you go the extra mile to make things look nice. If your going to do it, you might as well do nice and right the first time. Looks absolutely stunning ❤
Have you considered using at least 1 lag bolt on the railing posts? Seems that people will most likely lean on that railing and being that the posts are mounted on the exterior of the deck framing, the person leaning on it will create a decent amount of outward force. I would just worry about someone leaning on those rails and ths screws pulling out. May not happen immediately, but could occur slowly over time. I would highly consider putting at least 1 lag bolt on each post.
You could’ve cut a channel into the 4x4 like you did the 2x4 and “boxed” in the wire and hid your cut ends and strengthened the edges on the side. Looks great love your videos!
Another idea for the paint for the structural framing is the vertical posts paint black and the horizontal band paint white. It’s definitely going to be the best looking Coyote ugly blind!
Minnesota has been talking about daylight savings junk for 6 years and every single year it’s “the last time you will have to change you clock” lol maybe next year or the following or following of the following 😂
I started laughing as soon as u measured the table saw to cut ur notch out and Noticed right away u added an inch. Loved when u caught it nd actually put it on video
10:58 always awesome when it's off enough that you catch it instantly like that. As soon as you put the board up there my brain said 'that's not centered' as yours did.
Maybe you could put rivet thread inserts in top of posts you wanted to put the bar boards on and just break it out when needed. So best of both worlds. If that makes sense.
I always make the back side a hair bigger so it doesn't bind up. Dang 6" screws thru the post for the rails. I'd just pre drill w counter sink and side screw them to post but that will definitely hold good. Looks great!
Should of put your post in before your decking inside the corner and box it in with your framing it’s the strongest way to build your railing would’ve saved you lumber aswell
Just a thought, what do you think about adding a deck under the blind with a plastic table and a couple of chairs for BS ing and other (squirrel) monitoring and RC Trucks.
I think it would look cool if the deck framing was black and the braces white. The stairs stringers black with white steps. Might be too much work, and the white steps will probably get too dirty anyways, but I think it could turnout pretty cool like that
House and finish work looks amazing!! Just curious though with the railing being the same height as the bottom of the window opening whats your plan for the "rock thrower" if it needs to be at a sharper down angle?
Was just about to comment damn that was a quick fix on the saw!! Apparently not!! 🤣 You need to buy the stand for that saw man, not cheap but saves your back and knees!!
Hey Dmaxryno a nother great video on your channel for 2023 u definitely my favorite TH-camr for a while now keep up the great work awesome TH-camr u are
Better if the shed stays tan ( not to mention it would weather better than white ), and that "detail" between the top rail and the sub top rail would look cooler than leaving off the top rail.
@@DMAXRYNO ok ,am a true believer, and I take you at your word,for I know your word is all you got, and I know your a stand up guy, Love your channel, God Bless you, these tools are on my x-mas list
You mean like the times we voted to get rid of Governor gruesome and it didn't work because they use the Dominion voting machines so he can buy votes ? 🤔
I like your building projects wish you could move your wearhouse out to the ranch do you can build it however you want or maybe see if ypu can move it into your friends place that got that big place for him and his family.
100% not a big enough difference to justify the price difference. If you aren't already invested in the milwaukee lineup, then the hercules line is great to jump into. Batteries are WAY cheaper!
Why didn’t you just only cut a corner off the corner posts that you need to make a 90° turn with the 4x4’s that way it all looked symmetrical all the way around?
Getcha some 💸💸💸!
workforitapparel.com
Do you have any 3xl hoodies. I checked the website but they all seem to be out
Just a side question is your tape true or forgiving?
Tbh I get excited to see another hunting blind video. I’m not tired of the vids, I love seeing every step of the process
I’d say add the little bar top thing! You’ll enjoy it! Beers and controllers and slingshots!
That 1” gap would be perfect for some mood lighting. White when hanging out and red when it’s squirrel tie.
I absolutely love how you go the extra mile to make things look nice. If your going to do it, you might as well do nice and right the first time. Looks absolutely stunning ❤
Have you considered using at least 1 lag bolt on the railing posts? Seems that people will most likely lean on that railing and being that the posts are mounted on the exterior of the deck framing, the person leaning on it will create a decent amount of outward force. I would just worry about someone leaning on those rails and ths screws pulling out. May not happen immediately, but could occur slowly over time. I would highly consider putting at least 1 lag bolt on each post.
You could’ve cut a channel into the 4x4 like you did the 2x4 and “boxed” in the wire and hid your cut ends and strengthened the edges on the side. Looks great love your videos!
Watching your hand on that table saw during that notching process had my pucker factor at a 10.
Haha I was very careful, but it’s definitely not the safest way to do it b
Another idea for the paint for the structural framing is the vertical posts paint black and the horizontal band paint white. It’s definitely going to be the best looking Coyote ugly blind!
Minnesota has been talking about daylight savings junk for 6 years and every single year it’s “the last time you will have to change you clock” lol maybe next year or the following or following of the following 😂
Would be cool if you put a Firemans Pole behind the portion of the railing that isnt complete yet. Tactical way to get down and flip your RC cars!
Your building content is honestly my favorite part of this channel
That railing is looking badass!! That is going to be a really nice blind!!
No clickbait no pranks, just hard work 🤘🏽
I started laughing as soon as u measured the table saw to cut ur notch out and Noticed right away u added an inch. Loved when u caught it nd actually put it on video
Am not sick of these builds. There great.
10:58 always awesome when it's off enough that you catch it instantly like that. As soon as you put the board up there my brain said 'that's not centered' as yours did.
Love the hogwire idea, finishes out the building perfect. Awesome job Ryan!
The railing looks really sweet. I would’ve milled in the sides like you did the bottom and top.
That wouldve saved that bottom groove from holding rain water
What's up Ryno Looking Like The Red Headed Stranger ,Bird Watching Booth Looking Good,Love your channel Brother, God Bless you
Nice roadwork repair.
That should hold up nice for tomorrow's heavy rainstorm.
Maybe you could put rivet thread inserts in top of posts you wanted to put the bar boards on and just break it out when needed. So best of both worlds. If that makes sense.
I think we all thoroughly enjoy this series Ryno
Ryno keep in mind that will make a great leveling for those pew pew things. Close and far adjustments
Stain the footers and decking with natural wood finish, paint “house” white, trim black
Wow that railing looks awesome great job
from life guard tower to Prison Guard Tower... Need some Gold Aviators and 30-06, Cool Hand Luke style.
I really like that rail system.
Man you need and rolling stand for that table saw and a little outfeed support. Ripping is a dream
Looking good 👍any resolution on front entrance project ? Would love to see it completed as I am sure you would as well.
I bet it's just the slider tubes on the compound miter saw that are twisted somehow. Is there a set screw to loosen the slides?
You and Offtheranch with the views of the sunsets and sunrises hahaha
Ohhh man the new t-shirt men make plans t-shirt is SWEET! .. just ordered one
Ryan, I use black tape on my Milwaukee guns and batteries keeps them from wearing out and getting lose connection adds longer life to my batteries
Looking good Ryan👍👍
Looking really good
Lil Dumpy FTW
Million dollar question. What is the latest saga with the front entrance? I'm dying to see that finished. I know it will look stellar.
Bolt cutters work really good for cutting hog wire.
I always make the back side a hair bigger so it doesn't bind up. Dang 6" screws thru the post for the rails. I'd just pre drill w counter sink and side screw them to post but that will definitely hold good. Looks great!
Hell yeah I love the way its coming out!! Keep up the awesome work! 🙏
Try spraying white lithium grease on where ur saw is supposed to slide and see if that helps it slide
Should of put your post in before your decking inside the corner and box it in with your framing it’s the strongest way to build your railing would’ve saved you lumber aswell
Beautiful railings !
Good call using hog wire.
Nice work, as always. 👍
I'm not sick of the lifeguard tower project. I look forward to the new videos!
That blind is comin along nice ryan! U said u needed another post at the far end to finish the railing. What about leavin it open n add a zip line?
Looks good- been following you forever you always have the same consistent work flow it looks good and i appreciate your detailed thoughts 💪🏼
Hey man, predrill those screw holes. The heat from running them in burns the coating and they rust and break off in short time.
Hmmmm, never thought about the coating getting burned off
Sucks we can't get Harbour Freight tools here in Canada.
Just a thought, what do you think about adding a deck under the blind with a plastic table and a couple of chairs for BS ing and other (squirrel) monitoring and RC Trucks.
Just an idea but I'd close in the bottom and use it kinda like a storage spot for the blind
STOKED !!!!!!
Don't know about anyone else but I like these videos
I think it would look cool if the deck framing was black and the braces white. The stairs stringers black with white steps. Might be too much work, and the white steps will probably get too dirty anyways, but I think it could turnout pretty cool like that
maybe make 2 section of rail that clamps on when you do the RC cars and keep then in the blind so they are out of the way?
The hunting blind view is so good people are gonna want to pay to hunt coyote you could charge premium rate
House and finish work looks amazing!! Just curious though with the railing being the same height as the bottom of the window opening whats your plan for the "rock thrower" if it needs to be at a sharper down angle?
Might be a little tough if they're right below it
Was just about to comment damn that was a quick fix on the saw!! Apparently not!! 🤣
You need to buy the stand for that saw man, not cheap but saves your back and knees!!
Ryno does good quality work
Bro the railing looks really nice all black
Keep the good work up brother
Hey Dmaxryno a nother great video on your channel for 2023 u definitely my favorite TH-camr for a while now keep up the great work awesome TH-camr u are
Better if the shed stays tan ( not to mention it would weather better than white ), and that "detail" between the top rail and the sub top rail would look cooler than leaving off the top rail.
15:47 favorite part 😂
Your videos from Sema on Harbor freight made me do more research on the Hercules line and satisfied with my purchase
Awesome! I’m impressed with the quality they put out these days.
did you ever get your saw fix or just running it as is
honeatly enjoyed the building series
Makes me want to build a luxury shed 😅
Yo Ryan,Hog wire looks good,great idea !
Do a 2x4 on top of the posts and then a peice of square edged trex as the bar top
Also for the corners u could have gotten it with one post just cut out 1/4 of the bottom
stain the deck legs like a red cedar color i think that would be a good looking combo
Bolt cutters are the fastest and easiest way I’ve found to cut the hog panels
Why didn’t you set the post on the corner? I feel it’d look cleaner then the 2 next to each other.
Thought about it after the fact lol
Should try using the harbor freight airless paint sprayer on the building
Quick question, did you use the killz paint to help prevent the wood from molding or did you use regular latex paint?
looks like you need a fire pole? is that what they called? idk 🤷🏻♂️
you should put a small bar or something under the luxury hunting blind that extry stop down there do something with that don't just leave it blank
Where did you get the black hog wire?
Home Depot. It’s nice stuff but overpriced in my opinion
Que paso with your Harbor freight impacts,broke them already
Nope still going strong. Left them in my other truck which wasn’t at home.
@@DMAXRYNO ok ,am a true believer, and I take you at your word,for I know your word is all you got, and I know your a stand up guy, Love your channel, God Bless you, these tools are on my x-mas list
You never lose daylight with the time change. There is the same amount of light the day before and the day after daylight savings.
Any time we vote in something that makes sense in ca they don't actually do it.... Seems about right
You mean like the times we voted to get rid of Governor gruesome and it didn't work because they use the Dominion voting machines so he can buy votes ? 🤔
But at least we have beaches
@@lavishlex ya ... From all the rain I now have beach front property 🤣
Been a long time since we’ve seen cash in the mail🥰
Is that pressure treated
I finally order my Willy shirt. So glad you had them made. “Support the ass”
Dang are you ever gonna get the camo hats back in stock
Should have drilled some weep holes in your bottom channels. That way water doesn't just sit and rot that lower so fast.
I did after this was filmed
Just placed an order!
Thank you!
Why not have a single corner post on each corner? Would give the railings way more rigidity
I like your building projects wish you could move your wearhouse out to the ranch do you can build it however you want or maybe see if ypu can move it into your friends place that got that big place for him and his family.
would you say that the hercules is maybe somewhat close to milwaukee
100% not a big enough difference to justify the price difference. If you aren't already invested in the milwaukee lineup, then the hercules line is great to jump into. Batteries are WAY cheaper!
15:45 😂👍
16:58 every time I use my hand as a dead blow hammer, I also immediately regret my decision. 😂
Why didn’t you just only cut a corner off the corner posts that you need to make a 90° turn with the 4x4’s that way it all looked symmetrical all the way around?
Now it seems like its time to get some solid walls and make it a safe room on the bottom 😂
If you push in the middle of that hog wire, doesn't it pop out? I feel like that would be a safety issue.
It doesn’t flex enough to pop out, but I plan on adding trim to fully lock it in
Ryno are you going to put a fenced door on the deck so that no animals can get up there?
Hermano, we need more beef jerky and bacon, please 😊
We need some jerky back in stock!!!!! 😂
We’re working on it! Hope to have it by the end of the month!
Texas 🎉
If you're gonna do the big ledge put a 1 inch on the end so phones or controllers can't get pushed off.
Good idea