Thank you Hunter. Can't wait until part 2. As this video is going I have a note pad and taking notes. I appreciate you answering my question and even making a video out of it too. Thank you again Hunter.
Super-informative and well presented. I started carving that bull sacrum. I decided on a Cobra (head-on) surrounded by bamboo and a dragonfly or two, which I intend to color-fill. I had to stop carving after basic outlining, as I only had round burrs and will be restarting at the end of the month. Currently busy getting the garden ready/planted and with all the rain it is slow going. Since you present this so well, I suggest you catalogue the vids (in playlists?) for tutorials. Again, of all the diy vlogs I have seen, yours id the first I rate a 6 on a 1-5 scale. Thanks for thinking of others as pursue your goals!
That's great! Looking forward to hearing how it goes. Yes, so much rain! I think you are right, I will work on a playlist :) Thanks as always for the support.
Hunter, thank you for these really helpful videos! I have a question. I ordered an inverted cone bur and I was surprised that it does not have a cutting surface on top of it. Only on the sides. The top of the bur is smooth. Is that the same as yours or not? Thanks.
Hey Bob! The majority of inverted cone burrs do not have a cutting edge on the top. The part of the burr that is really doing the most cutting it the outer edge of the top of the cone and not the top. You are kinda cutting at a sight angle most of the time which is the edge of the burr, if that makes sense.
So what I am using is the Flex Shaft by Dremel which actually just attaches to the dremel itself. I use the Dremel 4000. I would definitely recommend adding the flex shaft as it gives you a lot more mobility.
Hunter this came at just the right time. I just bought a universal chuck and the flex shaft and I got a couple cow skulls (free!) from a local butcher. While the bugs do their work on the skulls I’ll be getting burrs and learning about them. Thanks!!
Try this Howard, Lowes, Home Depot and some of the other hardware store hardly ever carry the inverted cone burrs unfortunately www.amazon.com/Dremel-108-Engraving-Cutter-32-inch/dp/B0006N72WU/ref=sxts_sxwds-bia?crid=2ZLRAJOSVV5WZ&keywords=dremel+108+engraving+cutter&pd_rd_i=B0006N72WU&pd_rd_r=6c8790cc-8bf3-45da-8c72-a088457734fc&pd_rd_w=WxJDl&pd_rd_wg=Y2pJ1&pf_rd_p=f0479f98-a32d-45cd-9c12-7aaced42b1ec&pf_rd_r=FTVPY5HJCCT8MS3MSP40&qid=1557843738&s=gateway&sprefix=108+engra%2Caps%2C130
➝ TOOLS USED IN THIS VIDEO
★ Small Inverted Cone Burr @t
★ Medium Inverted Cone Burr @t
★ Large Inverted Cone Burr @t
★ Dentist Style Inverted Cone Burr @t
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
➝ SKULL CLEANING TOOLS
★ Aquarium Heater @t
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
➝ SKULL CARVING TOOLS I USE
★ Dremel 4000 @t
★ Flex Shaft @t
★ Adjustable Chuck @t
★ Respirator @t
★ Ear Protection @t
★ Ball Carbide Burr @t
★ Inverted Cone Burr @t
★ Cylinder Carbide Burr @t
★ Large Ball Carbide Burr @t
★ Diamond Dust Burrs @t
Thank you for your videos. We need more because I am new. Where can I buy bone already prepared for carving small items like parts of jewelry?
كيف. لي. ان احصل. علي. هذه. العدا
Thanks heaps Hunter. Looking forward to part 2.
You bet Glen!
Check your links. Some are broken
Want to learn skull carving? Here is a free 7 page guide to show you exactly what you need to get started
usskullhunter.ck.page/bd2b65322a
Thank you Hunter. Can't wait until part 2. As this video is going I have a note pad and taking notes. I appreciate you answering my question and even making a video out of it too. Thank you again Hunter.
Ah you bet Jon! I couldn't remember who it was who asked so I am glad you commented :)
Super-informative and well presented. I started carving that bull sacrum. I decided on a Cobra (head-on) surrounded by bamboo and a dragonfly or two, which I intend to color-fill. I had to stop carving after basic outlining, as I only had round burrs and will be restarting at the end of the month. Currently busy getting the garden ready/planted and with all the rain it is slow going. Since you present this so well, I suggest you catalogue the vids (in playlists?) for tutorials. Again, of all the diy vlogs I have seen, yours id the first I rate a 6 on a 1-5 scale. Thanks for thinking of others as pursue your goals!
That's great! Looking forward to hearing how it goes. Yes, so much rain! I think you are right, I will work on a playlist :) Thanks as always for the support.
fantastic video bro
Thank you Sir!
Hunter as always thank you for all of your work and time and sharing!
You bet! Thanks for watching :)
wonder how an IPR bur would work....thinking maybe stippling
Yes, they work great for lots of different carving. I get them for free from local dentist.
are you in handyman videos?
Hunter, thank you for these really helpful videos! I have a question. I ordered an inverted cone bur and I was surprised that it does not have a cutting surface on top of it. Only on the sides. The top of the bur is smooth. Is that the same as yours or not? Thanks.
Hey Bob! The majority of inverted cone burrs do not have a cutting edge on the top. The part of the burr that is really doing the most cutting it the outer edge of the top of the cone and not the top. You are kinda cutting at a sight angle most of the time which is the edge of the burr, if that makes sense.
what is that respirator that you are using and is the one that you use primarily or only for quick videos?
I found the information in your handout! Thank you!
@@theflamingpearl Haha good to hear Pamela!
Is your second bid the Dremel 109 - 1/16 inch Inverted Cutter Engraving Cutter?
This is a very helpful TH-cam video for young artists and craters. Very recommend.
Thanks!
Awesome, I've used all of those burrs before but only on thin wood. That's the first time Ive seen the top of the heads used that way.
How can I buy these tool set??help me
Which do u prefer the hand piece your using now or a full sized dremmel as i just brought the dremmel3000 as i am a beginner
So what I am using is the Flex Shaft by Dremel which actually just attaches to the dremel itself. I use the Dremel 4000. I would definitely recommend adding the flex shaft as it gives you a lot more mobility.
Awesome. Can't wait to see the other videos on specific applications of various burrs.
Thanks! Yeah I found this video pretty fun so I am liking doing this series :)
@@usskullhunterDanke
@@urmelausdemeis3495 Hey!
Hunter this came at just the right time. I just bought a universal chuck and the flex shaft and I got a couple cow skulls (free!) from a local butcher. While the bugs do their work on the skulls I’ll be getting burrs and learning about them. Thanks!!
Sweeeet! Glad to hear you are getting all set up, and can't beat some free skulls!
U R 👌🏼 .. Thanks
So nice of you
Thank you! 🙏🏼
Do these tools and techniques also apply to carving antler?
Absolutely.
Thank you hunter
Appreciate the tips!! Do you have the product number for the Dremel inverted cone Burr?? I've looked for it and can't seem to find it at the store..👍👍
Try this Howard, Lowes, Home Depot and some of the other hardware store hardly ever carry the inverted cone burrs unfortunately www.amazon.com/Dremel-108-Engraving-Cutter-32-inch/dp/B0006N72WU/ref=sxts_sxwds-bia?crid=2ZLRAJOSVV5WZ&keywords=dremel+108+engraving+cutter&pd_rd_i=B0006N72WU&pd_rd_r=6c8790cc-8bf3-45da-8c72-a088457734fc&pd_rd_w=WxJDl&pd_rd_wg=Y2pJ1&pf_rd_p=f0479f98-a32d-45cd-9c12-7aaced42b1ec&pf_rd_r=FTVPY5HJCCT8MS3MSP40&qid=1557843738&s=gateway&sprefix=108+engra%2Caps%2C130
Thank you Hunter..Never received notification that you replied.. thanks
yippeeeee i get to learn about bits;];];] thank you hunter;];];];]
Haha you bet Patty :)
Can hear u but can hear the cars in back ground more brother
Sorry about that Jamie!
Great! You must have years of experience.
Glad to help Johan!
Does it ever get to hot and burn the bone?
Only if the burr is dull and then yes it can start to burn the bone.
Great tutorial Hunter.
Rock that Beard 💪💪💪!
Haha thanks man!
Thank you so much for the tutorial.
Yeah man! Thanks for watching :)
Great info. Thank you!
You bet, thanks for watching!
Thanks for the great video!!
Yes Sir, you bet Ron!