Beautiful, but very expensive + the charging is very wrong with the batteries. There must be a charging circuit in it + each battery is connected by itself, or they are charged in parallel
Hey there question would Lattepanda be able to run stuff like blender, zbrush, vroid, etc. Was wondering if it could Ru. Those along with some games even some high end ones if possible. Srry new to these stuff so don't know if Lattepanda is more geared to emulations and browsing
I had a small doubt i.e how much standby time does it give with 3s battery pack. I am planning to use a 4s battery pack with a bms to directly give power to my raspberry pi and boost converting it to 12v to give it to my display controller. This is one approach or should I just use 4 18650 cells and a powerbank module to charge it as well and power 5v to raspberry pi 4 and 12v to display controller via dc to dc boost converter??
series cells doesn't increase capacity, they increase voltage. you need parallel cells, and the capacity is gonna be determined by the quality of your cells. want a tip? recycle cells from old batteries from laptops, not all cells on them are bad, and work just fine
Although this is a good idea, it was thought out poorly. -With a display, compatible with lattepanda, you could just miss the display-driver part. -With such a thick housing it could fit 3X the battery. -Even if you want to use such little battery, just change the lattepanda to a raspberry pi and it consumes less power. -Displayless boost converter would consume less. -The hinge system is OK for a homebuild, but it should house less thick cables for a better look.(especially causes a problem when closing down, as visible on vid)
@@AhmadFarzadTaquee As an electrical engineer I believe it is quite doable for me, thanks. I have given ideas so that in the unlikely case someone wants to make this 'laptop' it can be done more efficiently and in a more long-lasting manner. I could have highlighted important parts, like the use of the mini BMS, but if one doesn't know the importance of that, then one should not even begin to build such a project, since it would probably be a nice fire hazard.
I have a question. Should both the voltage be the same when connecting the ADD board and the latte panda? Does it work for LP097x02-SLQA IPAD-3 AD board with DC connector and Latte panda 4pin or only for AD board in the video?
I built a similar device at home and can share my experience: Use rpi zero w or analogues (I took banana pi) and put a laptop cooler on it: for the purposes of such hardware, there is enough performance, it is better to install linux: again, performance. Zero w is compact, you can arrange the elements more tightly and put more batteries (read about parallel and serial connection) About charging, add a protection board, buy a fast charging trigger board, so you can charge using type-c
This is so amazing oh. This inspired me on my project that I intend to build. So I wish to ask how much does it cost for someone to build a laptop like this, and how do I get to start? I'm really anxious about it. This was so excellently
yes because the lattepanda is kind of a ripoff. you get a 2 core cpu for 600 usd. that is just a terrible deal. I mean I got a 4 core laptop for half the price. i mean my laptop has no fan, the lattepanda does but it has a worse cpu
Hello The assembly of the laptop components is so amazing. Please can you tell me how much it cost you to build a laptop. Second question, how do i start?
In Europe it is difficult to get all the components very cheaply. This only makes sense when you can build a machine with a first-class CPU, graphic card, and mainboard for half the price of a laptop from a store would cost.
the finished product looks great. However, there's a lot of wasted space inside the structure of the laptop, and a lot of components don't appear to be secured down properly. Also, it looks like you were in a rush to complete the build, which would affect the longevity of the laptop. I look forward to seeing improved builds.
Wow you made it without using 3d printer good job👌👏👏👏👏👏👏👏
thnx
@@SaptarshiSikder please give me all the list of items use please
You made it good
@@ifenyiwacharity7906 description, read desc ffs
Voice aati hai kya laptop me
It's even better then my real laptop
No backlight
No windows 11
No SSD
I really appreciate it 👍👍☺️
thnx
Dude your laptop is awesome it doesn’t have windows 11
windows 11 or lower doesnt matter, lightings doesnt too. the performance thats what matters.
When have they ever made laptops without backlights?
@@abatallWhy?
Nice job!
There are some display that you can use directly with the edp port of the lattepanda. You save a control card and power routing !
hmm
@@SaptarshiSikder I love you
@@tokedematthew5451then go and marry him 🗿
This is an amazing build
But using 3d printing It would have been way cleaner and smooth
not everyone has a 3d printer
I mean, I do but that isn't the point.
i wonder something Why is it necessary to separate the buttons between the screen and the computer? Why not make them the same button at all?
It's looks good 😍😍 specially the lighting part... 🤩
Thanku
How much money did it spend for you
Beautiful, but very expensive + the charging is very wrong with the batteries. There must be a charging circuit in it + each battery is connected by itself, or they are charged in parallel
Hey there question would Lattepanda be able to run stuff like blender, zbrush, vroid, etc. Was wondering if it could Ru. Those along with some games even some high end ones if possible.
Srry new to these stuff so don't know if Lattepanda is more geared to emulations and browsing
Is there any other way to make a latte panda alpha switch? It's because the toggle switch was too big and it didn't fit two pins
Thank you, what is the name of the keyboard?
check description
I had a small doubt i.e how much standby time does it give with 3s battery pack. I am planning to use a 4s battery pack with a bms to directly give power to my raspberry pi and boost converting it to 12v to give it to my display controller. This is one approach or should I just use 4 18650 cells and a powerbank module to charge it as well and power 5v to raspberry pi 4 and 12v to display controller via dc to dc boost converter??
series cells doesn't increase capacity, they increase voltage. you need parallel cells, and the capacity is gonna be determined by the quality of your cells. want a tip? recycle cells from old batteries from laptops, not all cells on them are bad, and work just fine
Although this is a good idea, it was thought out poorly.
-With a display, compatible with lattepanda, you could just miss the display-driver part.
-With such a thick housing it could fit 3X the battery.
-Even if you want to use such little battery, just change the lattepanda to a raspberry pi and it consumes less power.
-Displayless boost converter would consume less.
-The hinge system is OK for a homebuild, but it should house less thick cables for a better look.(especially causes a problem when closing down, as visible on vid)
Don't look at his faults, 🤨you can't even do what he did.
@@AhmadFarzadTaquee As an electrical engineer I believe it is quite doable for me, thanks. I have given ideas so that in the unlikely case someone wants to make this 'laptop' it can be done more efficiently and in a more long-lasting manner. I could have highlighted important parts, like the use of the mini BMS, but if one doesn't know the importance of that, then one should not even begin to build such a project, since it would probably be a nice fire hazard.
yeah the laptop could be thinner with a slimmer battery, if they want the battery to be that small
Does it tell you how mutch battery is in it, or do you just have to guess when to charge
I have a question. Should both the voltage be the same when connecting the ADD board and the latte panda?
Does it work for LP097x02-SLQA IPAD-3 AD board with DC connector and Latte panda 4pin or only for AD board in the video?
yes voltage are same 12 volt
Wow you gave me an idea to to this on my old ibm laptop! 😍
Do you think i can run Serato DJ on this SBC. I cant get an answer to this question but hear it can do every thing my laptop does.
yes
I built a similar device at home and can share my experience:
Use rpi zero w or analogues (I took banana pi) and put a laptop cooler on it: for the purposes of such hardware, there is enough performance, it is better to install linux: again, performance.
Zero w is compact, you can arrange the elements more tightly and put more batteries (read about parallel and serial connection)
About charging, add a protection board, buy a fast charging trigger board, so you can charge using type-c
How did you build it
Can I use this for running any of pcb designing software and Arduino droid extra?
yes
How are these tools to make this I am from Egypt
How to name this power board
Good laptop but If you're gonna make this a toutirial i would reccomend some protection of the battery discharge/charge
ok
How to charge this battery
i attach a acharging socket bro for charging
this is nice, plastic is not used. 8gb-64gb. last thing needed is better/tougher outer part
So in this case hardware like processor, graphics card etc are upgradeable?
How to make it act like a new brand computer an not like a windows or Apple?
Your videos are 100000 present real
Why did you add a fan 2:55
This is so amazing oh. This inspired me on my project that I intend to build. So I wish to ask how much does it cost for someone to build a laptop like this, and how do I get to start? I'm really anxious about it. This was so excellently
Thnx bro
Lattepanda 450$, display + ctrl card ~80$, keyboard 30$ maybe, battery 10$, cables+buttons 20$.
So my guess is around 600$
If I don’t have 3D printer and I want to make it can you tell me how can I
good job, but can you please cut a hole for the pc fan? without a hole the heat will trap inside and damage the hardware
The laptop is simply faster than mine
This pc is thicc that if it falls nothing happens to it, great job btw!
Bro lock screen of win 10 and after opening it's windows 11 how??
w10 11 r same lock screen
How many cost
30,000 rupees
1,00,000rs
This many
🫸 🫷
Well, you're no good. @VimalaAthnere-us1bd
Approx $650.Tbh it ain't really worth it
Bro mujhe sara saman chaiya kitne ma aayga
Bro instead of lattepanda can weuse because it's very costly
Your brain like a computer Bro😲😲
How much ram does it have
8
Cooling intake and exhaust?
Ok cool but what about USB?
How much would all part coast to make it please
From were you brought lattepanda alpha and what it is price
prise is 30000₹
How much it will cost
in future if it will be damaged so that How can we repair it by Own
yes
Bhai kitna paisa lagega ismein or kya kya lagega
46k inr 😂
Could've added a low profile graphics card if you wanted to game on it.
How much money did you spend in it to make this laptop mini
45000₹
Looks amazing but I think it would be cheaper to buy a regular laptop.
yes because the lattepanda is kind of a ripoff. you get a 2 core cpu for 600 usd. that is just a terrible deal. I mean I got a 4 core laptop for half the price. i mean my laptop has no fan, the lattepanda does but it has a worse cpu
Esmai keybord kq connection kayse kare ho to nhi hai bro....
bluetooth keyboard hai
How much cost for the parts u buy ? Plz reply
Bro how much GB ram and storage is there in a mini laptop
Atleast 1gb ram
what is that tape name at 10:15 ...plese reply
Double side tape
@@SaptarshiSikder outside display on bezel black tape...???
Bro can you make videos of how to order lattepanda alpha
Really Appreciateed your all projects 🎉. Esmai code nhi lagta kya ?
nhi bro or thnx
Hello
The assembly of the laptop components is so amazing. Please can you tell me how much it cost you to build a laptop. Second question, how do i start?
contact me in my instagram id
In Europe it is difficult to get all the components very cheaply. This only makes sense when you can build a machine with a first-class CPU, graphic card, and mainboard for half the price of a laptop from a store would cost.
Hy bro isme video call pe baat kar na ho to apni aavaj samane vali pass kese jaye gi
Mic use karo
But tell me name of the things that you used to made this
Nice job
Please the components used in creating it
check description
the finished product looks great. However, there's a lot of wasted space inside the structure of the laptop, and a lot of components don't appear to be secured down properly. Also, it looks like you were in a rush to complete the build, which would affect the longevity of the laptop. I look forward to seeing improved builds.
thnku
But The The Recovery Mode Says It’s Windows 10 11:47
Your Lying
What the price of this for making laptop pls reply pls reply what the price and which country are you from
From india
I am also from India
Proud of you
Please reply for making cost
@@sandhyapardhi4963 thnx bro lattepanda is so costly
please say how to buy this components
check description for buy link
What are the materials needed to make this
acrylic sheet
Total budget Bai 💥
Please show parts. Name
check description
Better specs than my both laptop 💀
This laptop is very awesome bro👌👌👌
can i get the lattepanda alpha at amazon or at flipkart
please tell me
no
@@SaptarshiSikder then sir
At which website I can get in INR
@@SaptarshiSikder in which site can I get for India please tell
Mini laptop kinte koto taka lagbe please replay den
bhai mere ko leptop kitne rs? me milega
Mom Can We Have A Laptop At Home?
Mom: we already have a laptop at home
Laptop at home:
My diy laptop went out fantastic
ohh u made one?
how much stroage it has
can i an play minecraft onit
64 gb
Nice video bro i wish to God for 1m soon
Thanks
What's the cost is for the all things
46k
Never Give Up 🔥
Thanks
Bro mini laptop ka raw materials kaha milega please batao
check description
Is there a way to buy this from you
how will everyone charge it?
Pls tell me the full cost approximately for making this please 🥺
Lattepanda 450$, display + ctrl card ~80$, keyboard 30$ maybe, battery 10$, cables+buttons 20$.
So my guess is around 600$
Does it work with ryzen 9
Great Work Bro 😎
Thank you bro
Nice editing brdr
thnx
@@SaptarshiSikder which software you use
Adobe Premiere pro 2020 Version
Koto porlo total cost eta banate vai❤khub sundor hoyeche
Kithne gb he
8gb ram
Can I use raspberry pi 4B ?
yes
where i find this parts
chk description
Can we play games and do online classes in this laptop
Ren de bhai 46k ka hai ise tu best desktop pc build kar sakta hai 😂
Bhai keyboard how to make 🤔🤔🤔🤔🤔🤔
keybord online ne karida
What's the total cost of making this laptop???
Bro can i do study and play games on it?
well the keyboard like surface
Sara parts kaise available hoga
chk description
Hello pls can anyone help me with a raspberry pi or lattepanda am an upcoming tech producer plss😢
how do you control its brightness from lantern panda 🤔
Такую штуку надо было собирать в деревянном корпусе. Тогда было бы супер.
chalta hai ky bhai chalta hoga to next video me dikhaooo 😊😊😊
I have been so hard to work that too but thanks for toturial
No bms on the battery, nice bomb!
Tht laptop u make is rlly awesome!!!
(I want one)
Thnx bro
@@SaptarshiSikder how many RAM do u used on tht mini laptop?
@@nickparadox2162 8gb
@@imSomebody-m4c thx