Salvaging A Scooter WheelChair for Parts & How to Charge a Bad (flat) Dead Battery: 041
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2017
- Salvaging a powered wheelchair for parts with DC motors, actuators, shocks, tilting power seat, and many more fun parts. It was not repairable in my opinion... so let's have at it!
If you want to support this channel or just see more content from me for free, please visit my patreon page.
/ jeremyfieldingsr
Technical Notes and Corrections
Nothing to report yet. - แนวปฏิบัติและการใช้ชีวิต
Thank you for not having music in back ground as you are working and explaining things it helps a lot when your trying to learn somthing
*you're
@@brethager3265 you’re what?
In a Post-apocalyptic Mad Max world, Jeremy would be a good friend to have. Love the video.
must protect this man!
That smile at the beginning, is just pure gold. 😂
+Edwin Dekkers I could not help myself :)
Had to rewind, but, your absolutely right, gold.
8088505217
@@JeremyFieldingSr, 808850217
*loot detected*
Jeremy;
It is quite obvious that you are not only highly intelligent and educated, but your creative mind is what seems to drive you to do what you do.
You remind me of my best friend Tom, who passed away a year ago. He too had an incredibly creative and inventive mind, with little or no formal training for some of the fabrications he produced, but rendered some of the most intriguingly sophisticated, yet simple solutions for obstacles that stood before him. Your channel is not only fun and educational, but is also immensely entertaining and practical.
I've subscribed to your channel and intend to spend a lot of time gleaning some ideas that you have inspired me to pursue but lacked the inspiration to do so.
Thank you for sharing your knowledge with the enthusiasm and candor that sets you apart from all the rest!
You're a genius!
My 9 year old son loves tinkering. I'm turning him loose on your channel to watch anything he wants. We pulled the power supply out of an old PC so he can have 3.3V, 5V, 12V at the least.
A lot of veterans groups collect these and try to refurbish them. Goodwill also sees quite a few of them. If they can't get them going, they will discard them. Guys looking for these sorts of cool parts could find a great resource there - and might find a great way to put their talents and skills to work to help out a deserving vet.
I edited the part where I describe its original condition more, but I don't think it was fixable without major cost. At first I thought I might clean it and sell it. But no way. Most of what made it a great wheel chair was literally disabled. As you saw... really only one motor was working, and the actuator for tilt was working. Everything else was corroded over. The damaged motor was completely rusted out on the inside.
A collection of parts may make a good video, or even a vocational seminar for the disabled on repairs to such. Keep the wheels turning for the fight right?
@@JeremyFieldingSr sweet project cars has a new video on how to renew old bad batteries with a $100+ welder
"Joy Detected" -- yep, I know the feeling! Great video!
+jims408 thank you!
Whereas small wall-wart power supplies like that are concerned, most of them are current limited switch mode devices. that is to say that they'll put out the maximum amperage and reduce voltage to preserve its internal components. It's not a great idea and if done repeatedly it will damage the adapter. What I would recommend doing is to take jumper cables and connect it to a working battery that is known to be good briefly but long enough to get the charger to start its cycle. This is a quick and easy way to see if there are any problems like self discharge too. Give it a bit of a charge this way and see if it loses any voltage over time. The battery will of course loose a little as the chemistry balances and settles into a charged state. Thus the first measurement of how much charge it has gained should be made around 15 minutes after charging it and then again the next day to see how much has been lost.
This is true for lithium 18650 cells too. The cheap Chinese chargers you can get off Ali Express that will charge two cells at a time charge them in parallel. For most intents and purposes this is REALLY BAD especially if you get a cell with an internal short. Fortunately you can tell this relatively quickly as one or both cells will become abnormally hot. Usually though, you can give a couple quick pulses from a known good cell to bring the dead cell's voltage up enough that most smart chargers will take over as if it were any other cell under normal circumstances.
As a warning to others, you should never charge lithium batteries in parallel unless they are a reasonably matched set. They explode quite violently and can cause personal harm to you and damage to your property. Lithium fires are no joke. Please be safe rather than sorry...
Just a foot note - DON'T try & put out lithium fires with water. The lithium reacts with water producing even more heat so you'll only make the fire more violent. Use C02 or powder extinguishers.
Jeremy, I just want you to know that you and I are a lot alike. I broke down an old wheelchair a few years ago and made a kite retriever out of it with one of the motors and the controller. Then I took the second motor and made a crab pot puller for my boat. In the last 5 days I have picked up and stripped down two treadmills. One will be used for an edge sander I am building and the other will be for a 2x72 belt grinder I will also be building. I've been thinking about making a go cart out of a wheel chair for a long time now but don't know if I'll ever get around to it. I do know the joy you get from doing this stuff, I love it too! Thanks for all your videos, I have really enjoyed watching them and you do a great job telling your story. Take care and be safe.
I don't know who originated the term "Edutainment", but it describes your channel perfectly.
I landed me a jazzy chair yesterday. And just now when I decided to try and find some videos on potential projects or info about the parts, I was stoked to see JF as one of them. You done know his shit's top notch
I just donated a wheelchair to the VA it cost my mother in law the price of a SUV.. and he put in on the side of the road... GREAT FIND!!!
Finally - someone with the insights I need to have is right here sharing his knowledge for anybody who wants to learn!!!!!! Just Subscribed ^__^ I've been designing technical schematics for an exoskeleton suit using what I know is being designed and mechanically applied 'and' using my imagination for what can be done.
This You Tube station is one of five most significant You Tube stations in existence today. This You Tube station is actually a technical and vocational course.
I have wanted a salvaged scooter since I read a diy remote controlled lawn mower blog somewhere. That's yard work I can get behind...while lounging...with a sweet tea.
Victoria Mathis now that's an idea I could live with.
Sounds like a great horror film
So much better than Christmas I would die happy if one of those landed in my garage
You're a genius!!! It's an honor for me to find your channel!
+Jon Schneider wow... thank you for the kind words. I am certainly honored you feel that way. Welcome to my neighborhood!
The chargers have a chip that prevents them from charging when the combined voltage is less than 18vdc. They also will automatically shut down when the batteries are fully charged and they will ten go into maintenance mode. Charging time is 8-12 hours, designed for overnight charging. If the charger shuts off quickly, say within an hour or two probably means the batteries have one or more dead cells. Also when we attempt to revive a low set of batteries we use an automotive battery charger for about four to six hours per battery.
Very well done Jeremy. As a retired Commercial HVAC man with 40 plus years behind me...three words: Ya done good.
I love your "cool thing detected" special effect. And that gizmo in the background in your into looks like a medieval computer tape-drive.
The old saying, "one man's trash is another man's treasure", well I see a chest full of treasures........
Great work! I’ve been thinking about buying a used one , tearing it down, and making a trailer tower for my 16’ utility trailer. Now that I’ve seen it broken down I will have to tackle that project. Tyvm for sharing
I have used the charging trick for years, since they put the voltage sensors in the chargers. Another 12v battery with voltage, in parallel, does the trick too! Awesome find, thanks for sharing.
Your idea for tricking the battery charger into starting a charge is PURE GENIUS!!! Gonna have to try that one, for sure!! Thanks
thanks to you, I have more more machines with motors that people have discarded than I care to admit :)
You are unique indeed man.
I have been waiting for the attack bots to have a go at you but only few so far,great. Cannot help the warm fuzzy feeling when i saw that,as your fellow countrymen say,shit eatin grin when we started the vid with you standing beside the latest find ! it was priceless, good on you and good luck from aust !
Just a couple of things. I love your description of "ridiculous manual labor".
I believe "Tinkerer" is a title we should all aspire to gain. Thank you!
+D's Bees Apiary Update ... LOL thank you!
Jeremy Fielding Machines are pretty awesome, but knowing when to do something by hand can save time and money too; starting nuts on bolts for instance. Some bolts are harder to replace than others, so not stripping the threads off is preferable.
I have truly enjoyed watching your videos - the humor, knowledge, and sheer joy are inspirational. Keep up the good work sir!
i stripped one down , bolted on mower wheels/tires , and mounted it under rear of a stripped down riding mower . worked great...for about 3 weeks .
What a veritable cornucopia of beautiful assemblies!
I felt the same joy in watching as you did in performing its disassembly - thank you for yet again sharing it with us! Advice of an Electrician: this is all Class II circuitry (under 30VDC,) but: fuse & verify polarities; monitor current & temps; satisfy charging curve per the battery.
Just an FYI - many/most of these electric wheelchairs have electromagnetic brakes on the end of the motor - the brake is released when power is applied to the brake - and the brake can be either 12v or 24v coil. The brake must either be removed or powered before you attempt to run the motor. The gearbox may also have a "freewheel" lever, which basically disengages the gearbox from the motor. Tip : old automotive 12v battery chargers have no "low voltage" cutoff, so they'll attempt to charge any battery. Most electric wheelchair motors rotate at between 3000 rpm and 4500 rpm... 350w continuous to 1100w peak... gearboxs around 150rpm to 220rpm. These are actually fairly durable motors, high torque, fairly low speed and cheap/easy to control. Applications are endless. Great video!
Hey Jeremy ... just wanted to chime in to let you know that I enjoy your videos immensely 😀 Love the way you present yourself in all aspects and your presentation is absolutely superb 👌 video editing is far beyond par 👊 as a fellow tinkerer, I always seem to learn something every time I view your videos and it makes my tinkering so much more of a therapeutic hobby when I have more options to explore with my finds 👍 keep up the fine work my friend 😎
+Machinist that is awesome thanks!
WOW! I have 4 or 5 of these scooters, 1 old one and 3 or so Hover,.rounds$ I love the take apart part! And the battery charging, Well, I've been looking for a way to revitalize the batteries and thanks to you brother, I now know! So far, You are my favorite channel my friend! By far!
Thanks mate! I had a car battery that was dead flat, and I thought was money down the drain, but now I have some hope to bringing it back to life. love your videos, and greetings from Australia.
Hi Jeremy, found your channel are weeks ago. I cannot get enough of it you are an inspiration a real role model. You have a fan here in South Africa.
+mahesh sukhram thank you for the kind words. I am glad to have you in my virtual neighborhood!
I just want to tell you that you are magnificent and inspiring to watch and listen to.
I always have marveled at those who were able to take and repurpose found mechanical electrical components and create a functional use outside it's original intent.
I have been able to achieve a growth in this area, however the level your at and confidence to dismantle and stay focused is astonishing and very impressive to me.
I am a fan and want to thank you for sharing your knowledge and talent with others in a clear, easy to understand way as you are a natural teacher with a brilliant mind.
I look forward to watching in amazement at whatever you are exploring as it is fascinating and enlightening.
Sincerely,
Randy Chavez
I used to work on these chairs, reconditioning them for the nhs. Check the batteries as they are usually gel and dont mix well with a standard car battery charger. You can tell those batteries are knackered as the sides are sunk in. When the knackered batteries are charging they swell and get hot, obviously when they cool they retract and sink in slightly.
+Richard Black yes... they are gel but I use the charger that came with them.
I open "sealed" gel batteries and top them up with water anyway. sometimes they come back to life (1 or 2 for 3 so far). I had one that wouldn't take more than 50mA but I left it charging on a bench psu for weeks, and it eventually started taking a full charge. Having said all that, high amp Li-ion are getting affordable.
Wow. Outstanding video! I really appreciate how you talk through your thought process. Thanks and keep up the excellent work!
+TheRubytuesday123 thank you!
This is the second video I watched. Love how fun it is to tinker with stuff, especially when it is free. Thanks for posting.
Free is by far the best part! Thanks for letting me know... that is what encourages me to post more videos.
Another great video Jeremy. Always really interesting and also really honest. Thank you.
hey bro your the reason i am so into circuit analysis other day even dusted off old maths cobwebs to fire the imagination so hats off from aotearoa nz
A spare set of cheap Allen keys are great. Angle grinder or hacksaw and you’ve got a new chuck mountable bit.
Hey great parts from that ! Its great to se just what makes the tick as well as what parts you can harvest ! Love these videos
Hi Jeremy,
Jackpot with the chair! I constantly do what you've been doing with regard to picking up many different things that people cast aside to the road and take them apart and make use of their parts doing something else.
A very important point to mention here is about batteries. Check the fluid level (electrolyte) in the battery cells. Use only distilled water to top them up. Charging electrolyte causes a caustic and volatile vapour in the cell chambers, so it's better to only trickle-charge, but in a well ventilated space!
I don't know how many videos you've made, but I'll be watching every one of them!
Great job, keeping going!
Best regards,
62 as of today!
Hi Jeremy,
62 what? If it's sixty-two years old that you made it to, then congratulations! It mustn't have been an easy task to make it this far whilst dodging traffic and other potential hazards to pick up electro-mechanical road kill!
I just clicked over to 54 a couple of months ago whilst trying to avoid the same hazards.
Have fun and Happy Birthday!
Best regards,
62 videos LOL
Jeremy, thank you for the great videos. Sense you are so kind to share with us, I will share with you.
If you are interested in saving the battery's and saving some money, you can. Even if the battery's have a small charge 1 or 2 volts, you may be able to save them. By refurbishing them.
Yes even a deep cell gel or a AGM battery can be refurbished.
1.Remove the fill caps on the top of the battery. Drain the battery's acid out into a catch pan. Use a plastic basin as a catch pan. Metal pans will be corroded by the acid. And fail.
2. Mix 10 oz baking soda in 2 leters of warm water. Warm water works best to loosen the gunk in the battery. Poor the baking soda water into the battery cells.
3. Replace the battery caps. Shake the battery, or role it so the baking soda water will get into all the corners and crevices. Place battery in a location out of the way and remove the caps.
4. Lit battery sit for an hour. Drain battery after 1 hour.
5. Fill battery with distilled water to clean out all the baking soda water. Replace caps and shake or role battery again so to clean the battery inside. Empty out water. Repeat cleaning process until no gunk is in battery.
6. Fill battery to proper level with 2 leters distilled water mixed with 10 oz Epsom Salts. Proper level is sometimes marked on the outside. If not, fill to just below the slit on the inside of the fill hole throat. Or just below the bottom of the fill hole throat. A 1/4 inch gap is good.
7. Charge battery on a slow trickel charge for 24 hours. With caps off.
After the 24 hour charge, chech for voltage level of 12.6 to 13.5 volts DC.
8. If battery did not charge to 12.6 volts or more, than load drain battery below 6 volts and recharge for 24 hours on a trickle charge. And recheck batter voltage level after the 24 hours.
Replace caps after charging.
FOR SAFETY: Use rubber or neoprene gloves, eye protection, and an apron of some sort to gard against any acid splashing while working with battery acid.
Dry cell battery's will have a silica (sand) in them. It is reusable. Just separate it from the battery acid with a coffee filter or an old rag. Than allow it to dry, and reinstall it back into the battery.
AGM battery's have a fiberglass in them. It should not come out. But if it does, use the same procedure as the dry cell silica battery, to recover the fiberglass. Reinstall as needed.
Always enjoy your videos. Thanks!
Interesting info on the battery charger voltage detector . I will definitely try this on my drill batteries. Great engineer . learning a lot . Thankyou.
Hi Jeremy, you Rock Dude! Your Engineering/Machinist skills are nothing short of amazing! Cool graphics too!
Your asking if tricking the charger is ok reminded me of the time I exploded a 6 V tractor battery many years ago. I was in a hurry on the farm one morning, to be ready to bale hay later that day I needed to be sure the tractor battery was up. The old Case 500 used a + ground, and you can figure out the rest of the story. I still thank the Lord I was moving quick that day, I only made it to the barn door 10 or 15 feet away when BOOOOM!!! I turned around just in time to see the top of the battery bouncing in the trusses some 18 feet up. My face was over the top of that battery just 15 seconds earlier! So watch your polarity!
I also have a background in electronics, your trick should be fine, I would probably favor an old fashioned charger to get them back to life, then finish with the auto charger. I've used a good car batt with a dead one to trick the stupid/smart charger when it was all i could find one day.
You may already know, If you need to parallel 2 or more transformers,they will act as though they have a polarity, get them wrong and the sine wave will be 180 deg. out of phase, but don't worry, they will let you know right away! lol
I would rather see you charge you batteries outside your shop, at least the big ones, and especially car batts, they can off gas Hydrogen Sulfide. Oh i just saw a vid on converting a uWave xFormer to a power Xformer with a voltage of your choosing. i.e. old fashioned batt charger! Just need 2 or 4 diodes and a cap. How much current can you get from you variable bench supply, there is your batt charger!
I'm happy to see i'm not the only one who dismantles old machines as a past time! : )
Regards, Mark
Cool video Jeremy. I almost felt like I was watching 'how it's made' in reverse, while you were stripping it down. Lol. Thanks!
Great videos my friend. One thing, that charger you got from your neighbor is the wrong one for those batteries. No wonder it wouldn't charge them. They come with actual chargers for those uncharged batteries so keep an eye out for them. My father in law is wheel chair bound and I'm always having to repair his. I've purchased several chargers for the batteries because he keeps running over them. Fifty bucks or so from the dealers. Blech!
Greetings. Thank you for sharing your knowledge. I just discovered your channel and I enjoy it immensely. Please continue to share.
Man I learned a lot in this episode. Really useful stuff and a great video as always! I also really enjoy those cool graphics you use when you remove a useful part. It reminds me of winning or finding a reward in a video game haha.
+JackstandJohnny yes! Thank you
I hope to have 2 wheelchair's next week to strip down. And thanks for the info on the batteries,i will look into/try this info. Have a great weekend Jermey
That sounds fun!
I just discovered your channel. I can't stop watching your videos. Your very talented. Thank you for sharing.
Thank you! Welcome to the neighborhood
I almost scored one of these myself but didn't have the time/space to store and tear it down. What a nice pile of goodies Jeremy! Also the solid and dash lines indicates pulsed DC which is what most home electronics run on since true DC is a little more costly from a manufacturing standpoint. Your charging trick will work for a while but the wall wart usually has a thermal device or a diode or something like that that will pop once the load gets to high or the charger pushes back to much nothing dramatic but the wall wart will be toast. You could check the batteries periodically and remove the wall wart once the voltage starts coming up.
Yes... there is a note on the screen in the video that says unplug or disconnect it after about 15 seconds... that is all it takes to get the charger to do its job. I just pulled the wire out after a few seconds when I was doing it the first time.
.
the inforamtion you mentioned about the travel charger (the negative & positive) were very useful regardless of whether this procedure is safe or not , thank you .
+FOMI1970 thank you. I always try to plug little details that I found helpful when I learned them.
I enjoy and learn from your channel ! Thanks and keep up the great videos.. Harvey
The wheelchair motors have an electical brake system on the motors where your lever goes and must have power to release it. In wheelchair mode take the electrical brake off the motor and you can use it for anything you want like your shredder. The torque off the wheelchair can tow a car although slowly as I've told my daughter off many times.
A friend has one in his van to pull motorcycles into the van that's on a sled type holder for the bikes in shipping.
Thanks for your help on this project.Good educational advice!
Battery gold... wish I could hit thumbs up more than once
Hi Jeremy, You didn't just get an electric wheelchair, but instead, the Deluxe! That larger charger is one like mine. I got it cheap at a flea market. I removed the plug, put 2 battery clips on and after reverse engineering the circuit, I modified it to charge 12v batteries and added a volt meter to the front panel. Sweet charger with an unusual circuit that uses SCRs to control the output voltage.
As for the smart charger cheat you used, that's the way to get it to work. No danger as long as you unplug the wall wart as soon as the so called smart charger starts. A smaller wall wart probably wouldn't work - too weak.
+Inspironator awesome!
Thanks for being a thinker tinkerer! I fall short,but appreciate copy cat ideas off the masters! haha.
Thank you my friend what you doing. Very nice of you.
Now new problem where to put all the scrap from curb shopping....great video my friend you have continued to amaze me with your abilities and ideas...tinker on your a gifted man... best wishes
Unless there's a local ordinance against it, in most places there's at least one guy who picks up metal scrap for recycling sales, so just put it by the curb with a "free" sign on it and the disposal problem is solved. If you get lots of larger stuff, the next time you see a guy with a truck full of scrap metal ask them for their phone number. Now you don't even have to move it- they will load whatever you've got themselves.
Thanks for the tour of an electric wheelchair. I suggest you use protection for your hands, such as latex gloves, to prevent the crud from causing problems. I see no problems using a trickle charger as you did on gel cells. Using high-capacity chargers on lead acid batteries can cause hydrogen explosions if the vapors are not removed and you remove the charging leads- one of the reasons I don't hear so well.
+Jeffry Blackmon awesome thanks
Jeffry Blackmon I have a small lead 12v 1,4 Amph battery for my scooter that is completely flat. If I understand you correctly, can I not charge it with a charger like this?
your the best youtube channel ive been looking for a channel like this
Welcome to the neighborhood!
Interesting video, I am just starting to convert a Shoprider to haul a little trailer for the events we put on for our local town. I am planning to strip off as much weight and unwanted bits as I can while leaving it able to convert back. Looking forward to the testing.
By putting the wall wart on the battery first - if the battery was shorted it would show up real quick but the wall wart will not supply enough power to actually explode. IE - reasonably safe.
I do it all the time with sealed lead acid batteries. Be sure to check the fluid level before trying. Add distilled water if necessary.
Good video - thanks for posting.
+zalmaflash thank you.
zalmaflash I have a small lead 12v 1,4 Amph battery for my scooter that is completely flat. If I understand you correctly, can I charge it with a charger like this?
Yes but you need to check the water in it FIRST. Google it - sealed lead acid battery fluid.
if the battery is shorted the wall wart might explode though (if it's not protected)
Another great video. Thanks. Rather timely of it to pop up in my TH-cam suggestions as I just saw a scooter/wheel chair yesterday, for free in the local classifieds. Now I'm thinking I better go get it. Anyhow, another thumbs up and subscriber. Thanks again.
That is awesome! And welcome to the neighborhood!
Thanks so much sir, very useful. Learned a lot, that battery trick is awesome.
Really enjoy your videos
Nice hack. I'll try it on a few "bad" batteries I have. Thanks.
Great show!
I like the effects displaying the single elements!
Would be great to get a shot showing the whole scene from time to time and not only a little part!
But great show! :)
+Alex Cio thank you for the feedback. I didn't think of it but I agree that would add some value to the video. Thanks again
I got a wheelchair and it actually works great! Not sure what it will be used for but it’s fun to ride around
Awesome find! I'd love to see you take apart that bad motor and try to bring it back to life. Even if there is no chance it would be the ultimate guide for motor scrappers. Thanks.
I just might do that.... thanks for the suggestion.
Jeremy Fielding I have a 3 HP motor from an old compressor that spent a year barely covered by a tarp outside and I'm assuming it will be dead or need some love and attention....so my suggestion was purely based in self-interest :)
Talk about a score! I gave away a hydraulic wheelchair lift from my van when I bought it before I discovered my knack for tinkering. What I wouldn't give for one now.
It was pretty awesome.
Take cover from the storm my friend.
Cheers.
Freaking love your channel!!!! Instant thumbs up and subscribe!!!!! Thank you so much for making the motor series. Can you make a vid on which chairs and stuff make for the best source of useful motors, parts and salvage for us makers?
Who is this guy!! Excellent. I love it! And he even says he's not an electrician........Geez... :)
So some Motors have a collector. And you are also a collector. A motor collector grin
cheerio from Germany
Alfred E. Neumann? Sorry, dating myself. Old mad magazine character.
Raleigh, yes, you are right. I was a fan of this magazin. :-)
you are a smart men, good point on fooling the charger... i will try that
First time I watched this video. And will try the battery trick as I have a couple of golf cart caddy batteries that won't charge because they appear dead to charger. I had thought to try an OLD style battery charger rather than these new "smart" chargers. But again - you are terrific. Thank you.
Thank you!
Actuators and tilting mechanism have me thinking router lift with tilting table! Can't wait to see what you do with some of your parts from this mobility scooter!
+The Fishing Hobby my friend I think you nailed it! Great idea
I've bought two power chairs from the thrifty store put a wheel barrow on one was great but stop working after a while I thinks it's a problem with controller these are so much fun.they have magnets in the motor ends used as breaks,great quick disconnect parts.you gonna love this toy I see you already do.
You bet I do (love it that is)
Thank you for your video it helped me fix my batterys.
That chair was a treasure trove of parts 'n stuff. I assume you're stashing all the cool nuts and bolts, etc. Those fasteners are so valuable when you've gotta go down to the hardware store for one or two items. Anyhow, I can't wait to see what cool projects you cook up in that vibrant brain of yours to use these parts.
I have very similar situation, neighbor put hoveround out on sidewalk.loaded it up. tore it down to about where yours is. I want something I can move things around yard with, call it the mule ha. the controller doesn't work, talked to nephew who does robotics, (is a contender in Robo Wars) he says just build heavy duty controller. motors seem good, batteries holding charge (was concerned about charging too, but seems ok, Looks like close to where I am on it. Keep up the good work, post another video to update when get a chance
That DC adapter trick is genius
Thanks ! cool tip on battery chargers.
I enjoyed the video, thanks!
Hi Jeremy , great parts for a future robots project.
While I was very poor, I had to get a trickle charger to work on a car with a dead battery I couldn't afford to replace. My solution was similar, but it was to put a AA in series (to get the voltage up juuuust high enough to make the trickle charger work) and then when it had started up, I quickly pulled the AA out of the circuit and connected the car battery. The slight charge boost got the battery over the threshold and it charged from there.
The AA was burning hot after just a few seconds of this, and definitely destroyed, but it got me to work the next day.
I just picked one up today. first time I've ever seen one on the curb
+Joe Puhel same here... that was the first then I got another just a week later! This one still works. I can't find a single thing wrong except the battery was dead. I don't want to salvage it nor do I want to sell it. I am conflicted lol
Seems like a lot of great parts on those!
+Kevin OConnell this was the ultimate wheel chair. Pretty great timing to meet my neighbor outside like that as he was tossing it.
Jeremy Fielding Awesome! Now he knows what you're into or looking for!
Another fantastic job
I have one of these that is literally brand new, batteries were flat though and un chargeable. And I have 3 mobility scooters, 2 for parts one working. All this belonged to my mom who passed away a couple years ago.
All the motors and controls work on the wheelchair and the one scooter and the scooter even has LED lights and a motorized seat height system.
The wheelchair was priced at $11K new I found the paperwork on it.
The batteries you have you should have kept the little wall wart on them for a couple hours to trickle charge them before hitting them with the main charger..
Also for wall warts, the striped lead typically means "center" of the barrel connector. With that said the striped lead is usually positive, however in audio related equipment the center connector or striped lead is negative. Not all wall warts have a striped lead either some have a ridged lead (heavier power supplies) and the ridged lead the same rules apply as if it were stripes.
In AC the ridged or striped lead is neutral (white) and runs to the wider spade of a US AC plug.
When I researched this model it was priced around $6k. As to the wall adapters. That is interesting. I don't remember where I got the one I was using, but it was as described in the video along with some others I have.But, I do have another I used within a day of making the video that was the other way around (stripped positive), so there seems to be some variation in the meaning as you described above. I will investigate this some more so next time I can convey this information more precisely and correctly.
Awesome video man much appreciated👍
You got a lot of nice parts out of that.
Jeremy , I love your videos. Very informative and if I was your neighbor you would have to get a restraining order to keep me away! I have access to one of those chairs as I volunteer repairing donations for the local Habitat For Humanity Restore. The chair has a bad controller and it costs too much to replace it. I just never came up with a use for the 24V motors and actuator.
Just subscribed love your channel thank you for explaining things the way you do simple things like the grey stripes on the wire you told us what that means thank you. I have a little shop and I like my cobble time you call it tinkering most of mine looks a bit more cobbled. Thanks for making your vids.
welcome to the neighborhood!