one of the three capacitors that you point to in the video broke off on mine. I see you replaced two of them so I was curious which capacitor you replaced the originals with. Thanks!
a little tip if there is a lie leg left on your compasiter you can extend it with wire so you solder the wire to the board gives you more room to work the resson I changed mine on one of the on another accident the last bit of the leg snapped any way my email address is dareiefarad1@gmail.com send me a email and I'll send the pic of my spare compasiter you can buy them in any electronic spare shop thanks farad
Im Santos from spain, i have a dji phantom 3 advanced with this problem, when i turn on the drone in fisrt time always show this fail: MC data error and show problem IMU inicialization and barometer inicialization, later i turn off and turn on the drone and all works correctly but always, in first turn on fail. Do you think this problem is posible from one of the capacitator you show in this youtube video.
So if I understand this correctly, when you replaced the original memory card with the 16 GB one, was the new card formatted and empty? or did you transfer the data from the old card into the new one?
osito021 no I format the card to a fresh empty one before I format it I saved it on my desk top to put on a new ad card but the card under the board went in empty with no data on it then I used one of my other sd card for camara in fact I didn't need to put any thing on it as the current firm ware is installed inside and came back with the folder on the card
if it's ecs error I think it's the powering on motors is the problem I never could fix that I had to bur a new board the copasater never gave me any error message but if you send me your email I'll send you a pic
1 of my motors must have got damaged during the 4ft crash because it's hard to turn by hand so I've ordered a new one. Hopefully when I've changed it the esc error will go away. DJI won't tell me where to get the capacitors, they would rather me spend a fortune sending it in to them. If you put the capacitor make and model number on here you would help a lot of people. Thanks for your reply
+Stephen Jones hi no problem I have to find the spare compasiter and Wright the details for you if you find an electronic shop they should sell the part you need I'll send you later today yes I had to change one of mine too but it didn't give me ecs error I think on ecs is a different part that need changing can't remember what it's called as I said I had to change the board for that one the copasater isn't a power source I wouldn't have thought but I'll send you later good luck bro
Could it be that the SD card was full and unable to load any more data? Sounds like you did the right thing by increasing the capacity but maybe if you can't do that then formatting the 4GB card would work?
Hi I'm Jorge from Honduras. Had a accident with my phantom 3 professional. My gimbal did not broke, but I tr flex got broken. I buy a flex on ebay and I chang it. But when I turn everything on I got no signal on my phone. But I can take picture and photo cuase when a I get the memory out and put on Y computer I see it. You ting this could help me
Hello jorge I broke a few ribbons but some on ebay not original or slightly thinner I found it didnt give me single it has to be the ribbon I say but cant be hundred percent sure are you sure not another app is taking permission to the Camara try closing app fully if it running on android I know that stop mine a few times
Hi Farad and thanks for this vidéo , on my p3p I have an esc error after the last update 1.9.60... I reinstal the firmware 1.8 and no esc error but à compas error I do another Time the update to 1.9 and the esc error came again..... If I change the sd card under the motherboard this solution my problem no?? Excuse my english I m french thanks a lot
Drone altitude Fly or Die hi I had that esc after a crash I had to change the board that you see on this video the sd card under if for flight recorder it keeps your log files it's strange after update mine came after a crash with one of the motors being damaged after changing the motor I got the esc which power related to the motor compass is a better fault to deal with try a small magnet on leg and move it around the compass that might get rid of it hope that helps you
Farad Dareie Hello, I have a micro sd card 16g connected to the go pro & it keeps telling me sd card error please change. If I do the same thing you did in your video do you know if it should fix my problem? I didn’t know the drone has an sd card inside.
for this video I only changed the sd card under the middle of the board but one of the crash thereis 3 round shaped copasitera like a small barrel two of them came straight of one in the front and one in the back where the battery side is and one in the middle what is the problem with yours
thankyou for this video I just did it on my DJI phantom 3 standard and worked thankyou you saved me 1 month of time
I am so glad it worked out for you too 👍👍
what capacitors did you use to replace with. I broke one off in a crash and can't find out which one I should replace it with. thanks
Hi Farad, is Luis Alcibar again, i mean in this video. Did you had to reinstall the fw? regards.
Luis Alcibar no I know what you meant no I didn't reinstall firmware it was ready to fly straight away after changing the sd card
Nice one!
one of the three capacitors that you point to in the video broke off on mine. I see you replaced two of them so I was curious which capacitor you replaced the originals with. Thanks!
a little tip if there is a lie leg left on your compasiter you can extend it with wire so you solder the wire to the board gives you more room to work the resson I changed mine on one of the on another accident the last bit of the leg snapped any way my email address is
dareiefarad1@gmail.com send me a email and I'll send the pic of my spare compasiter you can buy them in any electronic spare shop thanks farad
Im Santos from spain, i have a dji phantom 3 advanced with this problem, when i turn on the drone in fisrt time always show this fail: MC data error and show problem IMU inicialization and barometer inicialization, later i turn off and turn on the drone and all works correctly but always, in first turn on fail.
Do you think this problem is posible from one of the capacitator you show in this youtube video.
Hello my friend I'm sorry for late reply when I had that era by changing the card it's sorted out the problem have you sorted it yet
Was there any software from the manufacturer that was found in the card? Or was the card only holding flight records that are not that important?
osito021 no only flight logs
So if I understand this correctly, when you replaced the original memory card with the 16 GB one, was the new card formatted and empty? or did you transfer the data from the old card into the new one?
osito021 no I format the card to a fresh empty one before I format it I saved it on my desk top to put on a new ad card but the card under the board went in empty with no data on it then I used one of my other sd card for camara in fact I didn't need to put any thing on it as the current firm ware is installed inside and came back with the folder on the card
So in a nutshell, empty new micro sd card, under the board, before assembly. Thank you for the info.
osito021 yes hope it works out well good luck
Hi, I have an esc error and I need capacitors. No joy with the DJI forum so which ones did you use.
if it's ecs error I think it's the powering on motors is the problem I never could fix that I had to bur a new board the copasater never gave me any error message but if you send me your email I'll send you a pic
1 of my motors must have got damaged during the 4ft crash because it's hard to turn by hand so I've ordered a new one. Hopefully when I've changed it the esc error will go away. DJI won't tell me where to get the capacitors, they would rather me spend a fortune sending it in to them. If you put the capacitor make and model number on here you would help a lot of people. Thanks for your reply
+Stephen Jones hi no problem I have to find the spare compasiter and Wright the details for you if you find an electronic shop they should sell the part you need I'll send you later today yes I had to change one of mine too but it didn't give me ecs error I think on ecs is a different part that need changing can't remember what it's called as I said I had to change the board for that one the copasater isn't a power source I wouldn't have thought but I'll send you later good luck bro
Could it be that the SD card was full and unable to load any more data? Sounds like you did the right thing by increasing the capacity but maybe if you can't do that then formatting the 4GB card would work?
When I stopped the sd card the fault went I tried the sd card on a computer after and wasn't picking it up so I think the bash did the damage
Sorry when I swapped it
Hey, what info was on the SD card you took out?
normally it's your flight data but I still can't open or format the sd card
Great info cool video
Thank you
Hi I'm Jorge from Honduras. Had a accident with my phantom 3 professional. My gimbal did not broke, but I tr flex got broken. I buy a flex on ebay and I chang it. But when I turn everything on I got no signal on my phone. But I can take picture and photo cuase when a I get the memory out and put on Y computer I see it. You ting this could help me
Hello jorge I broke a few ribbons but some on ebay not original or slightly thinner I found it didnt give me single it has to be the ribbon I say but cant be hundred percent sure are you sure not another app is taking permission to the Camara try closing app fully if it running on android I know that stop mine a few times
HI what is the process to repair the MAIN CONTROLER DATA ERROR!
Vince Kaleta I think it was sane error on mine did you try changing sd card if that didn't work it might be the black box on top
Hi Farad and thanks for this vidéo , on my p3p I have an esc error after the last update 1.9.60... I reinstal the firmware 1.8 and no esc error but à compas error I do another Time the update to 1.9 and the esc error came again..... If I change the sd card under the motherboard this solution my problem no?? Excuse my english I m french thanks a lot
Drone altitude Fly or Die hi I had that esc after a crash I had to change the board that you see on this video the sd card under if for flight recorder it keeps your log files it's strange after update mine came after a crash with one of the motors being damaged after changing the motor I got the esc which power related to the motor compass is a better fault to deal with try a small magnet on leg and move it around the compass that might get rid of it hope that helps you
Farad Dareie Hello, I have a micro sd card 16g connected to the go pro & it keeps telling me sd card error please change. If I do the same thing you did in your video do you know if it should fix my problem? I didn’t know the drone has an sd card inside.
I see ok I've got a couple spare I've got it from a electric shop in crickle wood I'll send you the name of the compasiter
Hi nomaly my phantom 4 pro main controller Data error
what capacitors did you use to replace with. I broke one off in a crash and can't find out which one I should replace it with. thanks
for this video I only changed the sd card under the middle of the board but one of the crash thereis 3 round shaped copasitera like a small barrel two of them came straight of one in the front and one in the back where the battery side is and one in the middle what is the problem with yours