It's hard to find a locking magnetic bit handle that I liked so I made my own using a ACE Pro screwdriver and the Hercules bit adapter from Harbor Freight.
I needed a replacement handle to mine and was gonna buy a new one till finding this video. Saved me money and time since i had everything needed at home already. THANX
I made one of these today after finding this video yesterday. I used an old Husky acetate handle with the Hercules bit holder. I was going to use the ace handle but my local ace didn't sell those screwdrivers in singles. Thanks for the idea.
Nice Mod . I look for good screwdrivers at flea markets to Mod just have to beware some handles are molded right to the shaft are very hard to remove without damaging . tried heating the shaft to melt it out with mixed results . Thanks for the video
I warm the handle with a heat gun to pry it off the screwdriver shaft, then warm again & tap it into bit driver. When the handle cools, it forms around the bit driver shaft. Never loosens.
Cool. I made a 3/8 spinner handle from a Great Neck nut driiver with aluminum shaft and 1/4 hex to 3/8in drive socket adapter. I drilled out the end of the shift about 12 mm deep, heated it up, and pounded it the adapter. It came out so perfect, it's even better than my Koken 3/8in drive spinner handle. I keep a 1" short 3/8in extension with wobble on the end of it.
Clever, I like it. I wonder if dipping the shaft end of the handle into boiling water would soften it? Also, drill a hole into the butt end of the handle, and sink a short 1/4 drive shaft, so you can use the handle as an extension, or when youre driving a screw by hand and it gets hard, just pop a cordless drill on top of the handle.
Tracked down the ace driver cause I liked the feel of it best over other brand acetate handled screwdrivers. However that Hercules bit is nowhere to be found at any harbor freight within 150 miles (per website) decided to go check and sure enough they have spot for it on shelf but nobody has it in stock and not an item you can buy online
Holly shit I did the exact thing last week but used a craftsman handle! But I used a 3 inch nut driver and the same harbor freight driver. Great minds think alike.
Lol! I have another video where I made a 1/4 drive spinner with a old USA made Craftsman screwdriver handle, thanks for the compliment and yes great minds think alike 😉
Hi I'm from Brazil. Look on the Ebay website for a tool called Malco HHD1S CONNEXT - 1/4" Magnetic Standard Nut Driver. It's exactly the way you want it. Plus, its holder is super strong.
Very nice! I did something similar, except I turned the handle. I’ll have to pick up a locking bit holder to try. Wood Turned Multipurpose Tool Handle th-cam.com/video/iARN15h2RcU/w-d-xo.html
Great work and fantastic handle. Too nice to keep in my toolbox. I'd keep it in my pocket. Sadly, I can't have one. Here in the UK, postage kills us. The price of postage for a screwdriver from the US is enough to buy a Snap On van!
![Genshin Impact | กาชา Clorinde ไวฟุนั้น ควร C6 [เทสตัวละครต่อ]](http://i.ytimg.com/vi/SOVaBvL7K20/mqdefault.jpg)
Sir, you made that project look too easy. Thank You for the video. Have A Good Day! 🛻🚚🚛
You my friend, are a GEE KNEE OUS. Thanx for the video my Brother 👍 ⚔️ ✝️ 🇺🇲
Just made one using a Klein handle and a Dewalt bit holder! Awesome idea and awesome channel,subscribed.
dude really... this is freaking awsome... i love little tool projects like this,,,, so now im going to make me one too....
I love a good shop made tool. nicely done.
Thanks!
I needed a replacement handle to mine and was gonna buy a new one till finding this video.
Saved me money and time since i had everything needed at home already. THANX
Cool idea, I’d just put a sacrificial piece of wood on top of the bit holder before you start hammering. But great DIY none the less
I made one of these today after finding this video yesterday. I used an old Husky acetate handle with the Hercules bit holder. I was going to use the ace handle but my local ace didn't sell those screwdrivers in singles. Thanks for the idea.
Awesome! It's definitely a handy little tool, I find myself using it all the time
Just had this idea tonight because I didn't like any of the handles available with these bit holders already. Great video!
Very clever brother... I just made it and absolutely love it already!!
Nice! I will go make one for my own, Thank you for sharing.😊
Brilliant!!! wonderful idea !!! thx for sharing
Haha, this is almost exactly what I was about to make. Great minds think alike.
Nice Mod . I look for good screwdrivers at flea markets to Mod just have to beware some handles are molded right to the shaft are very hard to remove without damaging . tried heating the shaft to melt it out with mixed results . Thanks for the video
Awesome idea. I'll be making mine soon. Thanks.
Nicely done. Thanks for sharing.
Great tool! I like it!
Great idea and nice job!
Thanks!
I warm the handle with a heat gun to pry it off the screwdriver shaft, then warm again & tap it into bit driver. When the handle cools, it forms around the bit driver shaft. Never loosens.
Great job!! Cheers Stuart Australia.
Cool. I made a 3/8 spinner handle from a Great Neck nut driiver with aluminum shaft and 1/4 hex to 3/8in drive socket adapter. I drilled out the end of the shift about 12 mm deep, heated it up, and pounded it the adapter. It came out so perfect, it's even better than my Koken 3/8in drive spinner handle. I keep a 1" short 3/8in extension with wobble on the end of it.
Wow! Very cool!
Great idea!
Ya I love the big driver, I just bought it. I'm haven't a hard time finding a decent handle. Guess I'll have to buy one.
Clever, I like it. I wonder if dipping the shaft end of the handle into boiling water would soften it? Also, drill a hole into the butt end of the handle, and sink a short 1/4 drive shaft, so you can use the handle as an extension, or when youre driving a screw by hand and it gets hard, just pop a cordless drill on top of the handle.
you are a frickin genius
Great idea.
Good job, subscribed.
Really like that. I wonder if Ace screwdrivers are easy to get for those of us in Eastern Europe.
You're genius man
Thanks!
Tracked down the ace driver cause I liked the feel of it best over other brand acetate handled screwdrivers. However that Hercules bit is nowhere to be found at any harbor freight within 150 miles (per website) decided to go check and sure enough they have spot for it on shelf but nobody has it in stock and not an item you can buy online
Heat the shank up hot then slide it in the handle...
excelente
👍🏻
Holly shit I did the exact thing last week but used a craftsman handle! But I used a 3 inch nut driver and the same harbor freight driver. Great minds think alike.
Lol! I have another video where I made a 1/4 drive spinner with a old USA made Craftsman screwdriver handle, thanks for the compliment and yes great minds think alike 😉
P cool bud! Grab a Hazet bit driver on Amazon while they are on sale! I mean, or don't, it's up to you of course lol. I love mine tho.
The blue colour bit holder is vey cute tell me it's name and also tell that where we can buy that thing
It's the Hercules bit holder from harbor freight
The bit holder is cute .where we can buy it sir?
I picked the bit holder up at harbor freight and the screwdriver from Ace hardware.
Have you ever considered opening an eBay store to sell a 'stock' unit or a 'custom' unit with a specific bit holder?
I would put two part epoxy in the cavity before you put the bit holder in there
Hi I'm from Brazil. Look on the Ebay website for a tool called Malco HHD1S CONNEXT - 1/4" Magnetic Standard Nut Driver. It's exactly the way you want it. Plus, its holder is super strong.
Very nice! I did something similar, except I turned the handle. I’ll have to pick up a locking bit holder to try.
Wood Turned Multipurpose Tool Handle
th-cam.com/video/iARN15h2RcU/w-d-xo.html
Or just buy one
Mf u took a Chinese handle and put a Chinese bit in it and called it custom made
Great work and fantastic handle.
Too nice to keep in my toolbox. I'd keep it in my pocket.
Sadly, I can't have one. Here in the UK, postage kills us. The price of postage for a screwdriver from the US is enough to buy a Snap On van!
wiha 76000 & 38701