sraight to the point? he talked for more then 12 minutes before he finally mentioned a mesh network, then he talked for another 54 minutes before finishing!!
Finally an explanation that makes sense. I’ve added security cameras around my property, it’s only a 140’x 50’ lot and a metal garage and a wooden garage. I’m still watching the video and the reviews at the end to decide on which ones I need. Your video is very clear and concise in setting up the equipment.
Thankyou so much for the video - I really struggled with other instructions I found, but this was so clear, and the explanations of what everything was doing helped me get my system up and running in no time. 1 metre thick stone walls are no longer the barrier they were to the wifi.
Great video and very useful. One thing I discovered was the Granite on a wall (say behind a kitchen stove) will not let the Wi-Fi pass as granite is full of metal!
I appreciate your video. I’m not a techy person so I’m optimistic that you will read my comment sooner rather than later. I live in a RV Resort/Park in Arizona. The park has StarLink mounted on the roof of the clubhouse/office and it’s about 200 feet away from my travel trailer with a clear line of sight. I am receiving a minimum signal (sometimes no signal), and I would like to know the best way to boost the signal to receive a better WiFi connection. What do you recommend? What do we need to do?
That is a good question. You probably need a good extender. I would think maybe something like the TP-Link RE650 could get you close, but 200m is quite a long distance for an extender, ideally the RV Park should increase it's outdoor wireless coverage with more access points to help.
Great video. We’re building a new home and I’m trying to figure out how to wire our home. One clarification I’m looking for is, if you set up one mesh unit connected to Starlink and need additional units, are they connected via Ethernet or are they communicating with the mesh -‘new router’ wirelessly? Thanks in advance.
Great questions. They will mesh with the "new router" and repeat that wirelessly. If you can run ethernet to them, or some of them, then that will improve the network even more. I hope this helps
Fantastic video presentation - thank you. Have learnt so much in a short time. I have Starling & want to extend the router's network. Can I continue to use the original wireless router & then connect say two mesh devices to get additional reach a either end of my house (1 level but Starlink struggles to reach the ends) or do I need 3 additional devices - 1 to become new base unit & 2 satellites? Thanks again.
Great question. If you want to use the Starlink router still, then to not waste the first mesh device you would want to run an ethernet out to it somewher down the house. This possibly defeats the object of the mesh, so in that instance it is best to put the Starlink in bridge mode and get 3 units. With all things though there are lots of ways of trying things. You may find that 2 units will cover the house with the Starlink turned off, just for the simple reason the mesh units may work out better than the Starlink one. I would probably start with 2 and add another one later if needed. I hope this helps.
Each extender you need to consider as a user. It will also depend on the distance the extender is from the Starlink router. The further away the worse the signal will be for everyone, not just that extender. I woudl probably suggest you try not to use more than 3.
Really helpful video! Just wanted to know if I leave the Starlink in router mode and turn the tp-link decos into AP mode, hardwire all the nodes then will everything work ok?
@The_Tech_Geeks Such a useful video, thank you so much for making! We only have a couple of questions, might be a bit silly. We have the 1st version of Starlink (round plate): 1. Would it work with either Deco XE75 (cheaper) or Deco BE95 (wifi 7, expensive)? Would both do the job? 2. Does the first/main mesh device need to be right next to the Starlink router cause it connects with it via a cable or it can be anywhere cause it connects to Starlink router via wireless?
Great to hear from you. Unless you have Wireless 7 devices you probably don't need to go for the BE95. The XE75 will be fine or the X68 that we show in the video. As to how close does it need to be - Since the Deco is not repeating the Starlink Wireless, but creating its own network, as long as it is connected to the Starlink using an ethernet cable it can be up to 100m away from the router. I hope this helps.
So you have to have minimum two decos one that connects to Starlink via ethernet and the other where you want the extend such as another floor. Could I just buy 1 deco and connect wireless on 2d floor to starlink? Trying to avoid buying 2 decos and an ethernet.
The deco's ar enot repeaters so won't connect to another wireless device (ie the Starlink router) wirelessly and repeat the signal. You need at least one to be plugged in to the Starlink
Hello! In my case i need to expand my internet range so i can cover up the entire house, I would be using a mesh system (tp link x20 or similar). being that said, do i need to set Starlink router to bypass mode? Can i set up the first deco far away from the starlink router ? So that i have the starlink router broadcasting in the kitchen, 1 deco on main room and the 2nd deco on 2nd floor? or the first deco needs to be right next to the starlink? Thanks and great video! :)
Good question. The Deco system does not join the Starlink wireless and then re-broadcast it. It creates its own network. You don't have to put Starlink in bypass mode to make it work, but if you want the first unit to be some way away from the Starlink router, you will need to have run an ethernet cable to it to enable that. I hope this helps.
Literally, the one thing I needed to know was how do you hook up extra mesh boxes and he skipped right over it exclamation point I watched this whole video and he doesn’t say how the second or the third one will link to the first one! I’m so frustrated right nowI understand the first one gets LinkedIn via cable but what are you gotta do it once you start adding them?
Really sorry to have missed that bit. You will see when I walk through the Deco and other vendor apps it asks if you want to add other units. So in your instance if it is a Deco you are setting up you should be able to connect the first one by a cable, then turn the other units on, while keeping them close to the main unit and log in to the Deco app. Then you should have the option to add additional units and it will scan for them and add them. I believe you need to be logged in as the owner to be able to see the plus to add additional units. I hope this helps.
Hi! I have an Asus Router which i want to connect via ethernet to StarLink Router... i want to buy one more router.. the 3rd router should I connect it via ethernet to my Asus Router? And the asus router to my starlink router via ethernet also??
Good question - the 3rd router probably would be best to be set as an access point and then connected to the first ASUS router. If you keep it as a router then that is also fine you just need to make sure the IP range on the LAN does not conflict with the Starlink or the 1st ASUS router or nothing will route. I hope this helps.
I am confused by something you are doing that I am not able to do. I have the X68 mesh, same model you have there. I set it up, created a new wifi network. All seems well, but at 32:00 you run a speed test but I am not able to run an "Advanced Speed Test" through the mesh wifi. Only when I am on the default Starlink wifi. I am not sure what I am missing here, but it looks like you are able to run an advanced test on the new mesh wifi. I am wrong? I can't this test to work through the Starlink app when on the mesh wifi. Not sure if there is something I am missing here? Thank you for the video, this helped me enormously on getting our network setup better!
Thanks for the encouragement. It will possibly depend on how you have your Starlink router is setup and your Deco. It won't work if your Starlink is in bypass mode with the Deco as the Starlink router won't be "running" in that instance. My tests were done without the Starlink router in bypass mode, so that could be the only difference. I hope this helps.
I have some questions: is the bypass mode necessary to work with mesh? If yes then i will see only the mesh network right? If it is possible to not use bypass mode, the mesh network will still work? And i will see both starlink and mesh network? One last question, does the extender have another network or does it replace the starlink one?
Great questions. You don’t need to put the starlink router in bypass mode if you don’t want to. If you leave it alone then you will have two wireless networks which may work for you. As to the SSID ie your wireless name this will be the same across all mesh devices so you will end up with one single network. I hope this helps
Great video, but iam not a tech person, can i use any router,? I have some telstra router's, they have ether connections, or does it have to be specified for meshing.?
If you are looking to be able to repeat the wireless signal of your Starlink router, then you will need a device that has that option built in to it. Generally somethign like a Telstra won't, so you need a device that has that specific mesh functionality like the TP-Link one mentioned in the video. If you are just wanting to add in extra access points via ethernet cable, then you will first need the Starlink Ethernet adapter. You will also need to know how to configure the current routers you have as they will often be set by default to run on the same IP range as your Starlink router and so you need to change the LAN DHCP network to something like 192.168.10.1 on your current routers so that it does not conflict. Sorry if that answer is a little more technical, but sometimes it is easier to not re-use other routers you already may have unless you fully know how to configure them.
@The_Tech_Geeks it's all good, you answered everything i needed to know, i have already been looking for the inline cable and I can go from there. Thank you 👍🏻
We certainly have a number of options. If you are in Australia or New Zealand please email info@thetechgeeks.com and we can work with you on some options.
My neighbour (annex flat on our bungalow) has just got starlink (v2) get around 70-80mb in her flat/the garden next to the dish, but only 20-30 in our part of the house (around 15m away), what do I need please?
If you are wanting to share your neighbours connection, then really you should consider a point to point solution to link both of your buildings together and then a wireless access point in the house to allow you to connect. This will be the more reliable way to do it. I hope this helps.
You dont have to. It may work out better in the long run or if you have configured the LAN ips of the Deco in the same IP range as the Starlink, but it will be up to you. I hope this helps
Hi, what would be better. To just place the Starlink router in bypass mode and connect my own mesh system to it or to leave the starlink router as is and configure my mesh system as repeaters to the starlink router?
Good question. Depending on what solution you go and how you want to set things up, I would probably suggest you leave the Starlink as it is and build a different network name using your mesh devices. This gives you a fail back and a way to test things if you need and still easy access to the Starlink router settings. A neater solution is to put the Starlink in to bypass mode, but I would test and get everything running first so you know your mesh is active and working before you do that.
Hello Tech Geeks, I was contacted by my director to add starlink Internet at the office and we need to connect 650 to 700 devices at a time in the Building for staff. I am thinking of getting 6 starlinks and connecting them in a mesh network with 3rd party equipment. What would you recommend/advise in this situation?
Wow, that is a lot of devices. You will at least be able to load balance the Starlink connections. You won't be able to bond them together for a greater aggregated speed (well there are companies that can help you to do this but the traffic will have to travel through their network locations and out to to the internet) You will need a good router that can hand multiple WAN connections as a starting point. There are a few vendors that have those options. Ruijie has one, then most of the higher end router vendors do like cisco etc. From that point I would assume you would actually come down to a physicaly cabled network as with that many devices in a building I would image you have structured cabling in place so using a mesh would probably not be so appropriate. Not sure this helps too much, but may get you traveling in the right direction.
Good question. The Netgear is not a repeater / extender. It sets up a whole new wireless network. As a result it needs to have the ethernet cable plugged in to the Starlink Ethernet Adapter.
We have never tried this I am afraid. The Starlink routers have been a bit hit and miss from reading people's comments. In theory its throughput will half, but the router we tested managed about 800mb/s so even with half it should still do 300-400mb/s, but we have never tried I am afraid as you often get better results using 3rd party products.
I live in a metal barndominium and have two metal buildings that I would like to extend too and speed up Starlink internet in house and at other two barns. I’m not real comfortable w tech. Can you help me know what/which one best to purchase in Missouri, USA. Furthest building about 200ft away.
So I have tired both my router (TP- link Archer v600) and my deco mesh system (x50) with the starlink ethernet adapter and neither will work, they all show they are connected and "talking to each other correctly, I just get no connection to internet. The starlink alone works fine, and connects to internet. I live in rural NZ with no cell signal, so once I disconnect Starlink I am 100% offline. I'm wondering if there is something wrong with the ethernet adapter? previously with spark nz using both the TP- link router, and deco mesh, had connectivity with no issue ( was just slow due to copper lines)
Good question. It could be one of three things. Point 1 is the most likely. Please only make IP changes or firmware updates if you know what you are doing. Results can be unexpected and it is your responsiblity to decide how to act on the information below. 1. By default Starlink assigns IP addresses from the range 192.168.1.xxx Most other companies assign the same as a default for their routers. If you are not putting Starlink in Bypass mode then you need to make sure the IP address on your Archer (in this instance) or your Deco is not in the same range as Starlink otherwise traffic will not route and it will look like everything does not work. So in the config of your Archer or your Deco you need to change the default IP and DHCP range to be say something like 192.168.10.xxx and once applied everything may start working. 2. You have a faulty ethernet adapter. If you have a computer with an ethernet adpater try plugging it in directly. If it works you know the adpater is not faulty, but is the config of your equipment. The other option is to look for a link light on your connected equipment, ie your Archer or Deco. Does it show a green or orange connected light. If it does then the adapter is most likely working. If option one did not make a difference option 3 below may. 3. We have seen in some instances that the Starlink setup does not seem to recognise the ethernet adapter or if it does it does not seem to allocate out DNS correctly. We have seen these two simple actions fix a number of these issues. a. Upgrade Starlink to the latest firmware and perform a Stow and restart b. Go in to settings and put in a manual entry for DNS, for example using Google's 8.8.8.8 & 8.8.4.4
I am afraid every extender will impact the speed in the same way as adding 10 users to the same wireless access point. If you are wanting to add 10 families then you will want to think about a router that can give you some control over how the bandwidth is consumed so that no one family can take all the bandwidth for themselves and leave the other 9 with a poor internet connection
@@The_Tech_Geeks thank you for the feedback. Im planning to use ethernet through out. I set up my switch in my main room then form a star network of access points
So, I can just go ahead and connect a repeater without having to put my starlink on bypass mode? I’m a little confused cause I’ve been getting mix information regarding repeaters. All I wanna do is extend my starlink connection up another floor without having to buy the starlink wifi mesh and just use a 3rd party repeater. Is the bypass only for the wifi mesh like in the video? Please help
Good question. If you have purchased a repeater / extender like the TP-Link RE650 then you don't put the Starlink in bypass mode. That is only if you are building a mesh network. I hope this helps.
I have the deco mesh cylinders and I had nothing but issues for two days they were installed. My Starlink kept disconnecting and I did have the Starlink switched for it with the override but wasn’t working so frustrated. Do I need another router with the deco mesh?
I am sorry to hear this. This sounds like the IP configuration on the Deco was not quite setup correctly or the cabling was possibly wrong. It would need to be plugged in to the Ethernet adapter if you have a Gen 2 dish and the Starlink router will still need to be physically turned on, even if you have set bypass mode
@@The_Tech_Geeksyes I got the adapter and had it on and had it in bypass mode but for some reason it was not working with my cameras or tv so when I took it off I reconfigured it for the 2.4 for the cameras but not I can’t get my printer to hook up to the WiFi I also have another router not sure I have to connect that one to it ?!? So confused and annoyed
Not fully knowing your setup and the models you have choosen it is probably fairly difficult to advise what is going on in your setup. If you have turned off 5 Ghz, then that is probably casuing you some issue. Normally you would maybe split it out to 2 network names one for 2.4 and one for 5ghz, but I am not sure which Decon models that is supported on, but it sounds like you need both 2.4 and 5 running to allow you to get everything to connect.
I'm pretty new to starlink I just installed gen 3 yesterday and the wifi signal is really weak through out the house, I just need an extender for guests etc.. will the TP Link RE450 pair with the gen 3 router through the tether app?
That is a good question. The Orbi is a great solution and has proven the test of time so that could be an option or I would certainly look at the Ruijie EW3200 as my main router and add the M32 mesh devices to build on it. I hope this helps
I just connect my Starlink dish and am getting a dismal 3.7mbps I did the advanced speed test and it shows 171mbps SL speed to router to internet, but 3.7 wifi speed device to wifi router. What is happening here? Is my cable connection no good?
Good question. This means that your Starlink connection is getting 171Mb/s which is pretty good, but that your wireless connection, ie the bit you actually want to use is very poor. This could be due to how far you are away from the Starlink router (not the dish) It could also be the device that you are using to connect with. I would suggest trying the same test when within 1m of the Starlink router. If it is the same then it is either your Starlink router or your device. If it is fast when you are close, then you know it is the make up of your walls and distance from the router and you need to look at adding in some mesh devices to improve the speed. I hope this helps
Good question. to extend to another property you should really use a wireless bridge. We made a couple of videos covering this that may help - th-cam.com/video/ef6Ba4sSy4Y/w-d-xo.html & th-cam.com/video/sQ1fsikAtZs/w-d-xo.html
Such great technology… and no built-in ethernet without the $60 adapter? Must be an Elon product😅 Could you do an “old-school” WDS bridge mode with star link base and go to a router that way? Guess you pretty much answered that talking about repeaters…. I’m just amazed no Ethernet w/o adapter. Are celluralr networks creating a mesh system or repeating system, do you know?
The V1 version (round dish) had an AUX port, ie ethernet port. I believe the V3 routers will have an ethernet port back again. You can use an extender / repeater if you don't want to buy the additonal ethernet adapter. Cellular networks tend to work on an easier principal and that is you own the SIM and you can put it in any router you like. This normally avoids the issues and means you can create a mesh with no issues.
As we mention in the video the Ethernet Adapter is an optional extra. If you did not purchase it, then please log in to your Starlink account and go to account and you can purchase it from the shop. I hope this helps.
Great Question. You can do basic port forwarding, but I am afraid that won't help you on Starlink as Starlink does not give you an addressable IP from the outside world as they use Carrier Grade NAT
Do it properly, cable to Wi-Fi access points. Mesh and extender systems cause bottle necks and are generally rubbish if you live in a household with more then 2 users.
@@The_Tech_Geeks Admittedly, my comment was a bit harsh in it's tone and I apologize for that. But as it is, surely you can appreciate that people look for very specific content and help, and people prefer to watch short videos of max 10 minutes, rather than watch 2/3 of a movie. So if I look for "how to connect a wifi extender to Starlink" I already understand the difference between mesh & extenders. So I don't want to receive an explanation on what the difference is, nor do I want to fast forward/scroll through the video to find the answer to my question. Now you provide soooo much information in that video. And the individual sections are no doubt very valuable to different viewers looking for different answers. So why not break a long video down into shorter videos with different headings, such as "The difference between mesh & extenders", "how to install a mesh system to Starlink", "how to install an extender to Starlink" etc. The last one is what I was looking for, but your video was just too encumbered. So I watched someone else's 3 minute video and got the answer to the point. I would bet my bottom Dollar that you would get many many many more views if you broke your videos down into shorter videos. TikTok has stuffed the use of long videos up. Nowadays, everything has to be specific and as short as reasonably possible. All the best and good luck.
Hey, thanks for your further comments. I think you may have fallen in to the trap that you assume we run this channel to get views and therefore money from those views. This channel is actually here to answer questions our customers have. This video was made around a year ago when Starlink was just starting to get traction here in Australia. It was made for a very specific target audience of around 40,000 facebok users of two groups at the time. That audience had hardly ever had any usable internet at the time, even less the ability to extend wireless. It was meant to be a really over the top explanation. You will see we have put chapters on the video so people can easily jump to the sections they want. You will also see by the comments that most have found it really helpful. I have no issue with your point of view or your comments, it is just this video was probably not created for you, as you seem to know the concepts already. This was created for people that did not even know how to put Starlink together or what it even could do, let alone how to extend the wireless around their property. This video was created to draw people away from our telephone and email support and create a more self educational solution. From the 75k+ views I believe it has done what we needed. I hope this helps further.
The subscription I was using was the Roam version yes but the dish itself is a Gen 2 and that’s different obviously to the subscription being used. I hope this helps
Strait to the point, glad there is someone that gives clarity to the setup of mesh with Starlink, and not loving the sound of their own voice.
Thanks so much for the encouragement
sraight to the point? he talked for more then 12 minutes before he finally mentioned a mesh network, then he talked for another 54 minutes before finishing!!
@@fernandoc.136 Yeah, every video on TH-cam seems to have all these comments saying "Your video is the best video ever ". It's tiresome!
@@fernandoc.136yeah I was like…. Uggg to the point ? 57 minutes video,
Finally an explanation that makes sense. I’ve added security cameras around my property, it’s only a 140’x 50’ lot and a metal garage and a wooden garage. I’m still watching the video and the reviews at the end to decide on which ones I need. Your video is very clear and concise in setting up the equipment.
I am so pleased to hear it helped.
Best explanation of setting up a mesh system via a Starlink ISP! Appreciated that there were variations of equipment brands.
Glad it was helpful!
Thankyou so much for the video - I really struggled with other instructions I found, but this was so clear, and the explanations of what everything was doing helped me get my system up and running in no time. 1 metre thick stone walls are no longer the barrier they were to the wifi.
So good to hear. Thanks for the encouragement
Great video and very useful. One thing I discovered was the Granite on a wall (say behind a kitchen stove) will not let the Wi-Fi pass as granite is full of metal!
Great tip! It is always those little things that catch us out.
This video was excellent.
Really helped me. Thank you
Glad to hear that!
I appreciate your video. I’m not a techy person so I’m optimistic that you will read my comment sooner rather than later. I live in a RV Resort/Park in Arizona. The park has StarLink mounted on the roof of the clubhouse/office and it’s about 200 feet away from my travel trailer with a clear line of sight. I am receiving a minimum signal (sometimes no signal), and I would like to know the best way to boost the signal to receive a better WiFi connection. What do you recommend? What do we need to do?
That is a good question. You probably need a good extender. I would think maybe something like the TP-Link RE650 could get you close, but 200m is quite a long distance for an extender, ideally the RV Park should increase it's outdoor wireless coverage with more access points to help.
Great video. We’re building a new home and I’m trying to figure out how to wire our home. One clarification I’m looking for is, if you set up one mesh unit connected to Starlink and need additional units, are they connected via Ethernet or are they communicating with the mesh -‘new router’ wirelessly? Thanks in advance.
Great questions. They will mesh with the "new router" and repeat that wirelessly. If you can run ethernet to them, or some of them, then that will improve the network even more. I hope this helps
Verry good information thank you.
Glad it was helpful!
Fantastic video presentation - thank you. Have learnt so much in a short time. I have Starling & want to extend the router's network. Can I continue to use the original wireless router & then connect say two mesh devices to get additional reach a either end of my house (1 level but Starlink struggles to reach the ends) or do I need 3 additional devices - 1 to become new base unit & 2 satellites? Thanks again.
Great question. If you want to use the Starlink router still, then to not waste the first mesh device you would want to run an ethernet out to it somewher down the house. This possibly defeats the object of the mesh, so in that instance it is best to put the Starlink in bridge mode and get 3 units. With all things though there are lots of ways of trying things. You may find that 2 units will cover the house with the Starlink turned off, just for the simple reason the mesh units may work out better than the Starlink one. I would probably start with 2 and add another one later if needed. I hope this helps.
@@The_Tech_Geeksso if i ONLY want to extend the wifi of the starlink without bypassing it, is an extender good?
All the ones in the video will work well for you, yes
Thank you so much 🤔how many extends can Starlink take
Each extender you need to consider as a user. It will also depend on the distance the extender is from the Starlink router. The further away the worse the signal will be for everyone, not just that extender. I woudl probably suggest you try not to use more than 3.
Really helpful video! Just wanted to know if I leave the Starlink in router mode and turn the tp-link decos into AP mode, hardwire all the nodes then will everything work ok?
That is correct. The Starlink will still be managing the network and the Decos the wireless.
@The_Tech_Geeks
Such a useful video, thank you so much for making! We only have a couple of questions, might be a bit silly. We have the 1st version of Starlink (round plate):
1. Would it work with either Deco XE75 (cheaper) or Deco BE95 (wifi 7, expensive)? Would both do the job?
2. Does the first/main mesh device need to be right next to the Starlink router cause it connects with it via a cable or it can be anywhere cause it connects to Starlink router via wireless?
Great to hear from you. Unless you have Wireless 7 devices you probably don't need to go for the BE95. The XE75 will be fine or the X68 that we show in the video. As to how close does it need to be - Since the Deco is not repeating the Starlink Wireless, but creating its own network, as long as it is connected to the Starlink using an ethernet cable it can be up to 100m away from the router. I hope this helps.
So you have to have minimum two decos one that connects to Starlink via ethernet and the other where you want the extend such as another floor. Could I just buy 1 deco and connect wireless on 2d floor to starlink? Trying to avoid buying 2 decos and an ethernet.
The deco's ar enot repeaters so won't connect to another wireless device (ie the Starlink router) wirelessly and repeat the signal. You need at least one to be plugged in to the Starlink
Hello! In my case i need to expand my internet range so i can cover up the entire house, I would be using a mesh system (tp link x20 or similar). being that said, do i need to set Starlink router to bypass mode? Can i set up the first deco far away from the starlink router ? So that i have the starlink router broadcasting in the kitchen, 1 deco on main room and the 2nd deco on 2nd floor? or the first deco needs to be right next to the starlink? Thanks and great video! :)
Good question. The Deco system does not join the Starlink wireless and then re-broadcast it. It creates its own network. You don't have to put Starlink in bypass mode to make it work, but if you want the first unit to be some way away from the Starlink router, you will need to have run an ethernet cable to it to enable that. I hope this helps.
Great video very well executed.
Glad you enjoyed it
Literally, the one thing I needed to know was how do you hook up extra mesh boxes and he skipped right over it exclamation point I watched this whole video and he doesn’t say how the second or the third one will link to the first one! I’m so frustrated right nowI understand the first one gets LinkedIn via cable but what are you gotta do it once you start adding them?
Really sorry to have missed that bit. You will see when I walk through the Deco and other vendor apps it asks if you want to add other units. So in your instance if it is a Deco you are setting up you should be able to connect the first one by a cable, then turn the other units on, while keeping them close to the main unit and log in to the Deco app. Then you should have the option to add additional units and it will scan for them and add them. I believe you need to be logged in as the owner to be able to see the plus to add additional units. I hope this helps.
@@The_Tech_Geeks you da man! Thanks for your response and I totally appreciate it!
Hi! I have an Asus Router which i want to connect via ethernet to StarLink Router... i want to buy one more router.. the 3rd router should I connect it via ethernet to my Asus Router? And the asus router to my starlink router via ethernet also??
Good question - the 3rd router probably would be best to be set as an access point and then connected to the first ASUS router. If you keep it as a router then that is also fine you just need to make sure the IP range on the LAN does not conflict with the Starlink or the 1st ASUS router or nothing will route. I hope this helps.
I am confused by something you are doing that I am not able to do. I have the X68 mesh, same model you have there. I set it up, created a new wifi network. All seems well, but at 32:00 you run a speed test but I am not able to run an "Advanced Speed Test" through the mesh wifi. Only when I am on the default Starlink wifi. I am not sure what I am missing here, but it looks like you are able to run an advanced test on the new mesh wifi. I am wrong? I can't this test to work through the Starlink app when on the mesh wifi. Not sure if there is something I am missing here? Thank you for the video, this helped me enormously on getting our network setup better!
Thanks for the encouragement. It will possibly depend on how you have your Starlink router is setup and your Deco. It won't work if your Starlink is in bypass mode with the Deco as the Starlink router won't be "running" in that instance. My tests were done without the Starlink router in bypass mode, so that could be the only difference. I hope this helps.
I have some questions: is the bypass mode necessary to work with mesh? If yes then i will see only the mesh network right? If it is possible to not use bypass mode, the mesh network will still work? And i will see both starlink and mesh network? One last question, does the extender have another network or does it replace the starlink one?
Great questions. You don’t need to put the starlink router in bypass mode if you don’t want to. If you leave it alone then you will have two wireless networks which may work for you. As to the SSID ie your wireless name this will be the same across all mesh devices so you will end up with one single network. I hope this helps
Great video, but iam not a tech person, can i use any router,? I have some telstra router's, they have ether connections, or does it have to be specified for meshing.?
If you are looking to be able to repeat the wireless signal of your Starlink router, then you will need a device that has that option built in to it. Generally somethign like a Telstra won't, so you need a device that has that specific mesh functionality like the TP-Link one mentioned in the video.
If you are just wanting to add in extra access points via ethernet cable, then you will first need the Starlink Ethernet adapter. You will also need to know how to configure the current routers you have as they will often be set by default to run on the same IP range as your Starlink router and so you need to change the LAN DHCP network to something like 192.168.10.1 on your current routers so that it does not conflict.
Sorry if that answer is a little more technical, but sometimes it is easier to not re-use other routers you already may have unless you fully know how to configure them.
@The_Tech_Geeks it's all good, you answered everything i needed to know, i have already been looking for the inline cable and I can go from there. Thank you 👍🏻
EXCELLENT!!!
Pleased it helped
Thank you for clarifying all this do you habe a recommendation for outdoor mesh system. We need internet on the farm. Thanks
We certainly have a number of options. If you are in Australia or New Zealand please email info@thetechgeeks.com and we can work with you on some options.
This is Gen 2, right ?
Correct, this is the Gen 2 Starlink "dish"
You think using power line ethernet will be good as well? Already have some pf this. Jw
Yes, it is a good option as long as you have a direct spur to the mian locations.
My neighbour (annex flat on our bungalow) has just got starlink (v2) get around 70-80mb in her flat/the garden next to the dish, but only 20-30 in our part of the house (around 15m away), what do I need please?
If you are wanting to share your neighbours connection, then really you should consider a point to point solution to link both of your buildings together and then a wireless access point in the house to allow you to connect. This will be the more reliable way to do it. I hope this helps.
With deco, do you have to put starlink into bypass mode?
You dont have to. It may work out better in the long run or if you have configured the LAN ips of the Deco in the same IP range as the Starlink, but it will be up to you. I hope this helps
Hi, what would be better. To just place the Starlink router in bypass mode and connect my own mesh system to it or to leave the starlink router as is and configure my mesh system as repeaters to the starlink router?
Good question. Depending on what solution you go and how you want to set things up, I would probably suggest you leave the Starlink as it is and build a different network name using your mesh devices. This gives you a fail back and a way to test things if you need and still easy access to the Starlink router settings.
A neater solution is to put the Starlink in to bypass mode, but I would test and get everything running first so you know your mesh is active and working before you do that.
Hello Tech Geeks, I was contacted by my director to add starlink Internet at the office and we need to connect 650 to 700 devices at a time in the Building for staff.
I am thinking of getting 6 starlinks and connecting them in a mesh network with 3rd party equipment.
What would you recommend/advise in this situation?
Wow, that is a lot of devices. You will at least be able to load balance the Starlink connections. You won't be able to bond them together for a greater aggregated speed (well there are companies that can help you to do this but the traffic will have to travel through their network locations and out to to the internet) You will need a good router that can hand multiple WAN connections as a starting point. There are a few vendors that have those options. Ruijie has one, then most of the higher end router vendors do like cisco etc.
From that point I would assume you would actually come down to a physicaly cabled network as with that many devices in a building I would image you have structured cabling in place so using a mesh would probably not be so appropriate.
Not sure this helps too much, but may get you traveling in the right direction.
Mega-Second. Great video. Thank you.
Thanks so much
Does the netgear NEED the ethernet cable connnected to starlink to continue transmitting internet? Can the whole thing be wireless?
Good question. The Netgear is not a repeater / extender. It sets up a whole new wireless network. As a result it needs to have the ethernet cable plugged in to the Starlink Ethernet Adapter.
Any info on if I buy another Starlink router for mesh. Would the speed be similar to the original Starlink speed? Thanks for the help
We have never tried this I am afraid. The Starlink routers have been a bit hit and miss from reading people's comments. In theory its throughput will half, but the router we tested managed about 800mb/s so even with half it should still do 300-400mb/s, but we have never tried I am afraid as you often get better results using 3rd party products.
Starlink sells a mesh repeater on their store. It is different to the router
I live in a metal barndominium and have two metal buildings that I would like to extend too and speed up Starlink internet in house and at other two barns. I’m not real comfortable w tech. Can you help me know what/which one best to purchase in Missouri, USA. Furthest building about 200ft away.
So I have tired both my router (TP- link Archer v600) and my deco mesh system (x50) with the starlink ethernet adapter and neither will work, they all show they are connected and "talking to each other correctly, I just get no connection to internet. The starlink alone works fine, and connects to internet. I live in rural NZ with no cell signal, so once I disconnect Starlink I am 100% offline.
I'm wondering if there is something wrong with the ethernet adapter?
previously with spark nz using both the TP- link router, and deco mesh, had connectivity with no issue ( was just slow due to copper lines)
Good question. It could be one of three things. Point 1 is the most likely. Please only make IP changes or firmware updates if you know what you are doing. Results can be unexpected and it is your responsiblity to decide how to act on the information below.
1. By default Starlink assigns IP addresses from the range 192.168.1.xxx Most other companies assign the same as a default for their routers. If you are not putting Starlink in Bypass mode then you need to make sure the IP address on your Archer (in this instance) or your Deco is not in the same range as Starlink otherwise traffic will not route and it will look like everything does not work. So in the config of your Archer or your Deco you need to change the default IP and DHCP range to be say something like 192.168.10.xxx and once applied everything may start working.
2. You have a faulty ethernet adapter. If you have a computer with an ethernet adpater try plugging it in directly. If it works you know the adpater is not faulty, but is the config of your equipment. The other option is to look for a link light on your connected equipment, ie your Archer or Deco. Does it show a green or orange connected light. If it does then the adapter is most likely working. If option one did not make a difference option 3 below may.
3. We have seen in some instances that the Starlink setup does not seem to recognise the ethernet adapter or if it does it does not seem to allocate out DNS correctly. We have seen these two simple actions fix a number of these issues.
a. Upgrade Starlink to the latest firmware and perform a Stow and restart
b. Go in to settings and put in a manual entry for DNS, for example using Google's 8.8.8.8 & 8.8.4.4
Can i connect 10 different network extenders and 10 families on the same starlink without affecting its speed?
I am afraid every extender will impact the speed in the same way as adding 10 users to the same wireless access point. If you are wanting to add 10 families then you will want to think about a router that can give you some control over how the bandwidth is consumed so that no one family can take all the bandwidth for themselves and leave the other 9 with a poor internet connection
@@The_Tech_Geeks thank you for the feedback. Im planning to use ethernet through out. I set up my switch in my main room then form a star network of access points
So, I can just go ahead and connect a repeater without having to put my starlink on bypass mode? I’m a little confused cause I’ve been getting mix information regarding repeaters. All I wanna do is extend my starlink connection up another floor without having to buy the starlink wifi mesh and just use a 3rd party repeater. Is the bypass only for the wifi mesh like in the video? Please help
Good question. If you have purchased a repeater / extender like the TP-Link RE650 then you don't put the Starlink in bypass mode. That is only if you are building a mesh network. I hope this helps.
@@The_Tech_Geeksthank you for the help!
I have the deco mesh cylinders and I had nothing but issues for two days they were installed. My Starlink kept disconnecting and I did have the Starlink switched for it with the override but wasn’t working so frustrated. Do I need another router with the deco mesh?
I am sorry to hear this. This sounds like the IP configuration on the Deco was not quite setup correctly or the cabling was possibly wrong. It would need to be plugged in to the Ethernet adapter if you have a Gen 2 dish and the Starlink router will still need to be physically turned on, even if you have set bypass mode
@@The_Tech_Geeksyes I got the adapter and had it on and had it in bypass mode but for some reason it was not working with my cameras or tv so when I took it off I reconfigured it for the 2.4 for the cameras but not I can’t get my printer to hook up to the WiFi I also have another router not sure I have to connect that one to it ?!? So confused and annoyed
Not fully knowing your setup and the models you have choosen it is probably fairly difficult to advise what is going on in your setup. If you have turned off 5 Ghz, then that is probably casuing you some issue. Normally you would maybe split it out to 2 network names one for 2.4 and one for 5ghz, but I am not sure which Decon models that is supported on, but it sounds like you need both 2.4 and 5 running to allow you to get everything to connect.
I'm pretty new to starlink I just installed gen 3 yesterday and the wifi signal is really weak through out the house, I just need an extender for guests etc.. will the TP Link RE450 pair with the gen 3 router through the tether app?
Good question. Yes the RE450 will pair with pretty much any wireless network and repeat it. I hope this helps.
@@The_Tech_Geeks that helped thanks, it's the only model I could find near by.
Which is the best, beside tp link
That is a good question. The Orbi is a great solution and has proven the test of time so that could be an option or I would certainly look at the Ruijie EW3200 as my main router and add the M32 mesh devices to build on it. I hope this helps
I just connect my Starlink dish and am getting a dismal 3.7mbps I did the advanced speed test and it shows 171mbps SL speed to router to internet, but 3.7 wifi speed device to wifi router. What is happening here? Is my cable connection no good?
Good question. This means that your Starlink connection is getting 171Mb/s which is pretty good, but that your wireless connection, ie the bit you actually want to use is very poor. This could be due to how far you are away from the Starlink router (not the dish) It could also be the device that you are using to connect with. I would suggest trying the same test when within 1m of the Starlink router. If it is the same then it is either your Starlink router or your device. If it is fast when you are close, then you know it is the make up of your walls and distance from the router and you need to look at adding in some mesh devices to improve the speed. I hope this helps
I live in a remote area. I need the WiFi to extend 157 ft from its home location to another house. What do I do please help.
Good question. to extend to another property you should really use a wireless bridge. We made a couple of videos covering this that may help - th-cam.com/video/ef6Ba4sSy4Y/w-d-xo.html & th-cam.com/video/sQ1fsikAtZs/w-d-xo.html
Thanks for this @@The_Tech_Geeks
This really help to much
Great, pleased it did
Very usefull, thank you.
You're welcome!
Such great technology… and no built-in ethernet without the $60 adapter? Must be an Elon product😅 Could you do an “old-school” WDS bridge mode with star link base and go to a router that way? Guess you pretty much answered that talking about repeaters…. I’m just amazed no Ethernet w/o adapter. Are celluralr networks creating a mesh system or repeating system, do you know?
The V1 version (round dish) had an AUX port, ie ethernet port. I believe the V3 routers will have an ethernet port back again. You can use an extender / repeater if you don't want to buy the additonal ethernet adapter. Cellular networks tend to work on an easier principal and that is you own the SIM and you can put it in any router you like. This normally avoids the issues and means you can create a mesh with no issues.
My Starlink doesn't have an Ethernet port
As we mention in the video the Ethernet Adapter is an optional extra. If you did not purchase it, then please log in to your Starlink account and go to account and you can purchase it from the shop. I hope this helps.
I am looking at setting up home assistant and I have Starlink. Do the TP-Link devices allow port forwarding?
Great Question. You can do basic port forwarding, but I am afraid that won't help you on Starlink as Starlink does not give you an addressable IP from the outside world as they use Carrier Grade NAT
Muhteşem.
Thank you
Do it properly, cable to Wi-Fi access points. Mesh and extender systems cause bottle necks and are generally rubbish if you live in a household with more then 2 users.
Very true, but some people don't have that option, so it may not be great, but for some setups it is the only option, so have a place.
Sorry I won't lining elons pockets
No worries
Send iindonesia
I am sure you will find a local reseller who can help you.
57 minutes of waffling.....seldomly seen such a poor explanation on the simple basics. Ridiculous!!!!!!!!
Thanks for your comments. Generally we have encourgement the other way around and people like the videos, but hey sorry it was no use to you.
@@The_Tech_Geeks Admittedly, my comment was a bit harsh in it's tone and I apologize for that.
But as it is, surely you can appreciate that people look for very specific content and help, and people prefer to watch short videos of max 10 minutes, rather than watch 2/3 of a movie. So if I look for "how to connect a wifi extender to Starlink" I already understand the difference between mesh & extenders. So I don't want to receive an explanation on what the difference is, nor do I want to fast forward/scroll through the video to find the answer to my question.
Now you provide soooo much information in that video. And the individual sections are no doubt very valuable to different viewers looking for different answers. So why not break a long video down into shorter videos with different headings, such as "The difference between mesh & extenders", "how to install a mesh system to Starlink", "how to install an extender to Starlink" etc.
The last one is what I was looking for, but your video was just too encumbered. So I watched someone else's 3 minute video and got the answer to the point.
I would bet my bottom Dollar that you would get many many many more views if you broke your videos down into shorter videos.
TikTok has stuffed the use of long videos up. Nowadays, everything has to be specific and as short as reasonably possible.
All the best and good luck.
Hey, thanks for your further comments. I think you may have fallen in to the trap that you assume we run this channel to get views and therefore money from those views. This channel is actually here to answer questions our customers have.
This video was made around a year ago when Starlink was just starting to get traction here in Australia. It was made for a very specific target audience of around 40,000 facebok users of two groups at the time. That audience had hardly ever had any usable internet at the time, even less the ability to extend wireless. It was meant to be a really over the top explanation. You will see we have put chapters on the video so people can easily jump to the sections they want. You will also see by the comments that most have found it really helpful.
I have no issue with your point of view or your comments, it is just this video was probably not created for you, as you seem to know the concepts already. This was created for people that did not even know how to put Starlink together or what it even could do, let alone how to extend the wireless around their property.
This video was created to draw people away from our telephone and email support and create a more self educational solution. From the 75k+ views I believe it has done what we needed.
I hope this helps further.
This is RV version?
The subscription I was using was the Roam version yes but the dish itself is a Gen 2 and that’s different obviously to the subscription being used. I hope this helps