Thanks for the video. A tip for the intelligent settings, Shift + End for horizontal, Shift + PageDown (or down arrow) for vertical works after selecting the first pixel. Faster and error free.
Thanks for making the time to make this video. As I am doing the setup, everything goes fine up the the moment we need to tell the order of the pixels (minute 14:34) No pixel flashes on the panel. As I hold and drag my mouse on the matrix nothing shows on the panel. It's weird as all the previous steps lit up the panel and passed the test. Any ideas why it may fail at this last step? Is there a way to reset the controller, and start all over?
Great videos. Have a question: can LEDVision also adjust the shade of colors? I'm asking, because I had to buy LED panels that are now 2 different lot numbers and the colors do not match. I've also see a video on I-Set. Would it maybe be possible to do that with this software. Or am I stuck with having to purchase all new panels? Thanks for ALL you knowledge you are sharing with us
Great step by step, I followed it exactly, LEDVISION worked in testing modes, could not get FPP 6.3 to test pattern, if I went into xlights turned on play, but nothing to play, I could get FPP test patterns to work, as thought xlights starts up the demon on pie, but major flickers, tried 3 colorlight cards, Pie 3B+, Pi 4, still flickers so much, you cant watch it, any ideas
I have P6 16x32 panels. Tried to finish setup but LEDvision recognized my panels like 8x32. Did anyone have same problem? Any suggestions how to fix this?
I have just single panel. Can't get it past intelligent step where yuou should say how many lines there are. There are 8 lines , but on next test where you had single line it still has 8 lines, but around 50% dimmer. And after going on the map, it will blink 2 leds at the same time making it impossible to map anything.
So i got this working - it was wrong chip selected. But now I can map every other line and then remaining 4 lines blink at the same time and I can't complete it whatever I select. I could get it to work with another panel just fine, by following procedure.
Can you add eth connection to the PI with adapter as my WIFI will not reach the PI 4 running the color light card which is connected to the eth connection on the PI
I'm currently having issues with my screen. It's not been in use for close to 2years because the RCVBP file got corrupted. I need help. It's a colourlight X1 sending card with a colourlight recieving card. I need please
Dear Greg, while LEDvision 8.5 can display the test screen on my two 64x32 matrices, the image flickers (flickering seems in sync with the activity light of my gigabit ethernet nic-usb adapter). I can't seem to find another instance of this happening to someone in my searches. Might you have an idea about how to fix (or start fixing) this issue?
im working with: 1- Linsn RV908M32 Receiver 2- P4 Indoor LED Display Module 256x128mm 64x32 pixels 3- PC with - Realtek PCIe GBE Family controller - SO it's GBE but im failing when im trying to detect the receiver card, could you help?
I would try and find a Pi3B+ or Pi4, keep an eye on rpilcator.com (they do push feeds on twitter). If you're in the US then get registered on adafruit.com they typically have stock on a Weds.. if you're in the UK/EU then I have a few Pi4's at panelsrus.com
This was probably the MOST helpful video I have ever seen and been able to follow!!!!
How about a just in time post on the subject I needed 😀 Awesome!
Hi Greg
Thankyou for your detailed explanation and setting up of the colour lite card.
Thanks for the video. A tip for the intelligent settings, Shift + End for horizontal, Shift + PageDown (or down arrow) for vertical works after selecting the first pixel. Faster and error free.
I love you boss. i learn Many information of your video. God Bless you
great
Thanks for making the time to make this video. As I am doing the setup, everything goes fine up the the moment we need to tell the order of the pixels (minute 14:34) No pixel flashes on the panel. As I hold and drag my mouse on the matrix nothing shows on the panel. It's weird as all the previous steps lit up the panel and passed the test. Any ideas why it may fail at this last step? Is there a way to reset the controller, and start all over?
Great videos. Have a question: can LEDVision also adjust the shade of colors? I'm asking, because I had to buy LED panels that are now 2 different lot numbers and the colors do not match. I've also see a video on I-Set. Would it maybe be possible to do that with this software. Or am I stuck with having to purchase all new panels?
Thanks for ALL you knowledge you are sharing with us
pls i need this aswell!
Great step by step, I followed it exactly, LEDVISION worked in testing modes, could not get FPP 6.3 to test pattern, if I went into xlights turned on play, but nothing to play, I could get FPP test patterns to work, as thought xlights starts up the demon on pie, but major flickers, tried 3 colorlight cards, Pie 3B+, Pi 4, still flickers so much, you cant watch it, any ideas
I have P6 16x32 panels. Tried to finish setup but LEDvision recognized my panels like 8x32. Did anyone have same problem? Any suggestions how to fix this?
I have just single panel. Can't get it past intelligent step where yuou should say how many lines there are. There are 8 lines , but on next test where you had single line it still has 8 lines, but around 50% dimmer. And after going on the map, it will blink 2 leds at the same time making it impossible to map anything.
So i got this working - it was wrong chip selected. But now I can map every other line and then remaining 4 lines blink at the same time and I can't complete it whatever I select. I could get it to work with another panel just fine, by following procedure.
Can you add eth connection to the PI with adapter as my WIFI will not reach the PI 4 running the color light card which is connected to the eth connection on the PI
Yes, a usb Ethernet adapter can be used to link to the home/show network whilst the onboard Ethernet is connected to the Colorlight.
I want to do 12 panels wide by 1 high Can I do this on one color light card or Do I need to use 2 or 3?
I'm currently having issues with my screen. It's not been in use for close to 2years because the RCVBP file got corrupted. I need help. It's a colourlight X1 sending card with a colourlight recieving card. I need please
Can I just use the color light card and control it from x lights? Or do I have to use the raspberry ?
Dear Greg, while LEDvision 8.5 can display the test screen on my two 64x32 matrices, the image flickers (flickering seems in sync with the activity light of my gigabit ethernet nic-usb adapter). I can't seem to find another instance of this happening to someone in my searches. Might you have an idea about how to fix (or start fixing) this issue?
im working with:
1- Linsn RV908M32 Receiver
2- P4 Indoor LED Display Module 256x128mm 64x32 pixels
3- PC with - Realtek PCIe GBE Family controller - SO it's GBE
but im failing when im trying to detect the receiver card, could you help?
TENDRA EL ARCHIVO DE CONFIGURACION DE P10
I f you use RGBW cycle the colour order will follow White..
With Rasberry Pi's being extremely hard to find right now is there an alternative you could recommend?
I would try and find a Pi3B+ or Pi4, keep an eye on rpilcator.com (they do push feeds on twitter). If you're in the US then get registered on adafruit.com they typically have stock on a Weds.. if you're in the UK/EU then I have a few Pi4's at panelsrus.com
@panelsrus Sweet I'm on adafruits and Digi keys notifications hopefully one of them will have stock Wednesday:)
How do I set up Led Vision to give me a monthly playback report?
I dont believe it has that function.
what HDMI media player do you recommend to drive the content?
depends very much on your media, i have used Pi's running Kodi for media files - or an Amazon Fire Stick for example.