[Eng Sub][mini4wd] Motor Break-in Carbon brush ed.

I tried to make a motor break-in method into a video.
But this is not the correct answer.
I think the way of thinking is important.
【ミニ四駆】モーター慣らし カーボンブラシ編
• 【ミニ四駆】モーター慣らし カーボンブラシ編

[@josefpreyes]

great video finally a scientific proven break-in process, thanks for this

[@mixxdodici]

Great video! From Italy thank you

[@SuperJsToysChannel]

thanks for sharing your experience. I have an adjustable power supplier but no cooling system. I run a Hyper Dash Pro at 1.5v for 15,000,000 rotations (about 16 hours). The improvement was from 27,000 rpm to 28,000 rpm which was not as huge as your job. Was there anything wrong?

[@AZARASHI3ODN]

There are Hit or miss in the motor.
In the case of HDP, 3V, 30000rpm at the time of opening, I think it is "Hit Motor".
However, the 27,000 rpm motor is at a normal level, but if you break in, it will rotate about 30,000 rpm.
・Did you lubricate the motor shaft?
・Do you have a contact restorer?
Lubricate the shaft before break-in and use contact restorer after break-in.

[@SuperJsToysChannel]

@@AZARASHI3ODN I think the problem was that no lubricant the shaft before break in. I saw you did it. what's the lubricant?

[@rizvian24]

@@SuperJsToysChannel I'm using wd40 multipurpose lubricant to lubricate the shaft. My hyperdash is peaked at 30k RPM after 3 minutes break in with 5v

[@abdullakc]

Is this also working for sprint dash and ultra ? Cam I use normal grease like in the mini 4wd kit ? 8 hours running? Serious?

[@rendiiphone1926]

Good video 👍
hayo arek PJBS nonton ya... 😁

[@ganirahardjo3972]

Hallo, is the neodymum magnet has affected to increase strength of magnet inside the motor?

[@alexanderison3882]

During the 8hours continous break in do you need to re oil or just the oil in the beginning is enough? Is vodoo oil a good oil to put in the commutator before the break in process? Thank you :)

[@AZARASHI3ODN]

It is enough to add oil first.

[@karllim-a6227]

What's the app that youve used to check the magnetic of the motor?

[@clamitgaming9450]

is there a way to do this but for kids or is there an easier way?

[@mrpaolosubrabas]

Finally saw a same vid with english sub. 8 hours of breakin wont damage the motor? Im a little hesitant. Greetings from the philippines

[@AZARASHI3ODN]

Motor life is shortened. This can not be helped...

[@sastudio7370]

For 8 hours use 3V or 1V?

[@bkeebs8148]

Do you have break in videos for no carbon brush version like? Torque tune2? To be specific tuned motors?

[@AZARASHI3ODN]

The metal brush motor has not been recorded yet. May we do it someday?

[@bkeebs8148]

@@AZARASHI3ODN Thankyou :)

[@bayunotonegoro8099]

From your experience how many hours usually it takes to break in the tuned motor series?

[@rizkiauliaharahap6479]

@@AZARASHI3ODN hi do you alrady have the video break in for metal brush? Thanks!

[@Retrograde99]

I had problems whit my Motor it was stuttering a lot I bought these 3 layer carbon brushes do I need to run them in for a very long time to make good contact?

[@AZARASHI3ODN]

I think it's a good idea to take a long time to get used to the carbon brush slowly.

[@Retrograde99]

@@AZARASHI3ODN so wear it in ? It’s a 3v motor so what voltage should I use to wear it in

[@abdullakc]

Why do u type its not the correct answer ??

[@lunlin3161]

Is it feasible to use Tamiya 53508 lubricated carbon brush before break-in?

[@AZARASHI3ODN]

That's metal oil. It's okay.

[@lunlin3161]

@@AZARASHI3ODN Thank you. I think I know the reason for the break-in failure. I lack this step.

[@lunlin3161]

@@AZARASHI3ODN When the motor is cleaned, do I need to use Tamiya 87023 again for carbon brushes?

[@user-oq8ps2cn5c]

드리프트오일

[@SuperJsToysChannel]

oh my god. When I watch this video again today I found I put 'dislike' by mistake last time. Just corrected to like. XD

[@AZARASHI3ODN]

What is it! Thank you w