2013 Mazda CX5 won't shut off the way off
ฝัง
- เผยแพร่เมื่อ 11 ก.ย. 2024
- Here is a step by step video on how to replace the Shift Sensor out of a 2013 Mazda CX5. Car wouldn't shut down all the way. The engine would shut off but the auxiliaries would stay on, heat/air, radio, etc. This was the problem, haven't had a issue since replacing the switch.
Quick and easy with this video.
My notes from doing this:
A) It can be done without removing the console surround, but you will need a stubby Phillips screw ratchet and need some Pick Tools to release the switch assembly after the two screws are out.
B) Once the switch is out, it can be rotated up and forward so the plug is easier to access and pull out.
C) Note: The Metal bracket is the support for the rubber-coated tray.
Thank you for saving this 69 year old lady some money. Followed your tutorial and voila! Ordered my part from Amazon for $29.00, using your helpful part number.
Glad it helped someone!!!
Thanks! Just replaced on my 2013 Mazda using your video.
Glad it helped someone!
Just ordered this part (thank you for listing the part number) and I am eager to replace this part! Thank you for this video!!
Your Welcome! Not a bad project, only a few tools.
Thankyou SO much for showing this!
I’m sure it took me alittle longer than your time but your video made it easy!
Thank you sir! I’m happy it’s helping people out!
Thank you for sharing.
I used your video and repaired the old switch with super glue and baking soda. It cost me about $0.50 in materials, and about an hour of my time.
Awesome, glad it helped you out!
Can you elaborate on this please?
@@mb3775 If you mix superglue and baking soda it cures very quickly and very hard, so you can apply the superglue in a thick layer in the worn groove. Standard superglue won't cure if it is too thick. Once it has dried (only takes minutes) you can sand it down to the original shape.
Great video! Efficient and easy to follow. 30 minutes - done!
Hey thank you for watching!! Glad it helped you!
Thank you for sharing! Having the same issue so I’m going to attempt this!
Thank you for watching, happy it is helping someone out! Just take your time doing the job, everything is plastic and tabs and pieces can break easy
Thank you very much. I fixed the problem with this handy informative video.
Glad it is helping people out!! Wasn’t too bad of a project really
This is very helpful. Got my problem fixed. Thank you!
The cause of the whole problem is not a damaged module, but a worn piece of rubber on the button, which you can even see in the video. It is enough to glue it with a hard glue to make it work properly again.
where in the video? Timestamp?
@@knexfan100 you can pause the movie in time 3:14 and see this black button, it has a rubber cap, just cover it with hard epoxy resin glue.
I also had such a problem and a few weeks ago I fixed this way by hardening the rubber with glue. And I have no problem with the radio when turning off the car.
@@peter5230my 2014 CX 5 is having this problem. Does the epoxy trick last or is it better to replace the whole switch?
Nice. Part arriving tomorrow. Video was tre' helpful. Should be a breeze. Thanks for posting!
Thank you for watching! Glad it helped you out!
Thank you for the video! It made my replacement very quick and easy.
Glad it helped!
Thank you! Very useful. I took my time, a little over an hour. Everything works well. The Mazda CX-5 shuts off ....Finally!!!!
Hey glad the video helped with the project!
@@grizzlygreg8922 What is the part called?
@@nycmom3122 Shifter Switch part# KDYO-46-040.. Should be Between $50 and $100 depending where you go or look
Before everybody goes out and starts spending $70.00 and time doing this repair.... try slowing down your shifting motion into park. I did just that, and I have not had the problem again.The wearing sensor seems to pick up the action when slowed down. It may eventually give out at some point, but at least it will buy you some time for a while.
Exactly right, My wife messed around with it for almost a year until it eventually just quit working, cold weather seemed to make it worse then spring came and got better till the following winter lol
You can put car in drive while off and slip plastic cover over shift know without unscrewing knob
it worked! Thanks!
Your welcome!
Right on brother, did that and problem solve. Thank from TJ Mex.
No problem! I didn't expect this video to get as big as it has! But it has helped many people as you can see in the comments. Glad it helped!!!!
Worked perfectly!!! Thank you so much.
Glad it helped with the project!
Thank you for the video. I have the same problem but in Australia Mazda doesn't sell that parts. I have to get the unit that come with the gear shift & that cost me A$1k+
Well shit damn, yea that’s no good! I guess there is positives and negatives no matter where your at on the globe! Happy this helped some one though! Thank you for watching!
thank you. i dont know if i trust myself to fix this but at I know now.
It really ain’t bad, just got to take you time and be careful, everything is stupid plastic so it can crack easy if you are not gentle
I’m trying to find the part number but having a bit of trouble, also what websites do you recommend I buy the part from. I’m currently looking on rock auto
I have the same car and the same problem, do you have the part number for the switch? Thanks for the video!
Your welcome! I still have the old sensor part # is KDYO-46-040... just checked my amazon history and that is the part # i ordered
Thanks man.
Glad the video is helping someone!
Thanks for the video!
Could you please share the workshop manual if you have it?
I don’t have the manual, I just winged this project.. couldn’t find much on this fix. So i figured I would do a video
I have the same issue, but my one turn of Air-conditioning air flow, indicators stop working as well, when I push start button few time everything work okay, don't know whether replacing this part will help resolve all my issue ?
I would say the Shift Switch would not have anything to do with the air conditioning. That would be a possible loose connection somewhere maybe or a relay or fuse that is ready to blow or works when it wants too
Do you have the Mazda part number for the switch?
KDYO-45-040
Part Number?
Hello how much is the part? Where do I get it at?
Should be around $100 and at any auto parts store
Hello. Do u know the piece’s name replace?
Shift sensor/switch, there is plenty of comments with the part number and everything
Cómo se llama esa pieza nueva del mazda cx5 ...mi auto tiene ese problema
Shifter Sensor Switch part# KDYO-46-040
Yep same model and problem.
relative easy fix, glad it is helping someone!! Thank you for watching!