2007-2012 Ford Mondeo 2 0 TDI - Full service
ฝัง
- เผยแพร่เมื่อ 13 ก.ค. 2024
- This is a full service of my Mondeo. I change the oil, oil filter, air and pollen filter.
If you want to see how to change the fuel filter have a look at my other video at • 2007-2012 Ford Mondeo ... .
Resetting the oil service light • How to reset the servi...
I hope you find it helpful.
That's exactly what i needed.
Thank from France !!
Thanks for this video, saved me going over and realising we don't have the right tools..
You're completely out of your comfort zone and it shows quite well. So I'll drop my 2 cents on the way out! ;-)
Forget all that bullocks stories of warming up the engine, bla, bla... Start with the "oil", finish with the "oil". Or in other words crack open the sump plug, let it drain. Crack open and undo the oil filter, but leave it draining in place! Pulling the deep stick and/or the oil cap its fine. BTW leaving the deep stick laying on the engine is an excellent reminder of the ongoing operation! ;-)
MEANWHILE go do everything else you have planned. Like air filter, cabin filter, etc. When the rest is done simply swap the oil filter, now completely drained (dry). Put the sump plug in place . Add oil as needed. Voilà, done. Without creating a mess or spilling oil all over the place. All with the old oil well drained! These PSA engines are quite easy to work on, with the proper tips or sequences it's a breeze!
Oh! Worth mention. The old cabin air filter was an activated carbon filter. Usually used to help suppress smells. That's why it's so black, compared to the cheap non carbon filter you replaced.
One last tip. Use the minimum number/length of extensions needed for the job at hand. It will make your life easier. Best of luck, Cheers
What a knowit all .I've done plenty of these and he done fine
Thanks Nigel, very helpful. Greetings from Sydney
Just saved 60£ after this vid. Thank you, mate! Very helpfull!
thats great! now i feel more confident and will do it myself! thank you
I putting oil sump plug after change oil filter to be sure maximum oil been removed. I clean inside oil housing as well. Anythey nice clear video.
Hi Nigel,
Again a very clear video.
Just few details:
1) I usually put the floor pan back after re-filling. That allows to verify that there is no oil leakage.
2) the pollen filter is hidden behind the ashtray when the steering wheel is on the left side. One must remove the accelerator pedal to access it. Quite difficult !
3) I do agree with DoubleZeroUK : your pollen filter was not so dirty, it was an activated carbon filter. The new one is a standard one.
Nevertheless, this video is probably the best one available on TH-cam. Thanks a lot Nigel !
See you,
JBK
Thanks for the comment. I’ve never had a problem with the sump plug leaking.
That's brilliant thanks, going to look at the fuel filter one now.
Thanks Nigel. This was very helpful
Excellent tutorial, thank you.
Thanks Nigel. Very helpful.
Thanks heaps this was very helpful
very nice and clear video thanks very helpful
Very clear video Nigel. Shame I don’t have a mondeo! But principles much the same on my Touran.
Thanks im starting and this video help me a lot :)
Thanks mate this helped so much
Thank you! Excellent!
great video. I have changed the pollen filter from underneath the glovebox without taking out the glovebox. difficult but doable. Also, the oil change timer needs to be reset after change.
Denis Comerford. Thanks for the comment. There’s a link in the description for the service warning reset.
Hi Nigel great video, but one question have you ever dome power steering flush? or would consider doing one?
Use a couple of bricks on the front wheels if jacking the rear to stop the car rolling, otherwise make sure the handbrake is on. I jack up on the sills under the doors but near to the wheel arches. If you look you will see indentations, they are the jacking points. Put the axle stand in beside the jack and lower the jack so the car rest on the stand. If you search google you will find pictures.
Great video!
I've just done a full service on my Mondeo and found the section showing how to access the cabin filter was very helpful.
The engineers designing this car must have been in different countries and communicating by text message, I can't understand how they managed to make the cabin filter so inaccessible. I imagine that many garages just don't bother changing the cabin filter, mine was particularly filthy.
Well done. I’m glad it helped.
Very nice and clear job it help me a lot please just make the same with timing belt.
Really useful and clear to follow on the pollen filter. Excellent and suspect it's never been done on my 60 plate 2.0tdci Titanium X. However the oil drain plug is different (points down at the ground so very easy to do) but the oil filter is a nightmare, sitting under the front of the upper part of the engine so a socket only makes a few turns before it jams against the engine. Not seen this layout anywhere. Got it done eventually, but a couple of days after the full oil change. Grrr!!! Any thoughts why it's different? It's a 163bhp.
I always change the caper washer as vel.
Thank you.
Nice video. There is no need to remove glove compartment to fit cabin filter. Just flip the fuse box over and you will have much more space to manipulate to fit the cabin air filter.
Can you access the 3 bolts on the filter housing when the glovebox is in place?
Removing the glove box gives you more free access rather than working claustrophobically. Make your life easier not harder
love to see a video on the auto transmission
I always change the O ring and the sump plug as its only a few quid
Hello Sir, would mind tell me that 2010 mondeo TDCI should use which type of breaking oil? Cheers
Great. You just saved me a 100£. Now to find one to drain automatic oil.
last time when i ask one garrage to service my car they said 200£ wtf :D :D
Also corresponds to Mk4 Ford Mondeo 2.0 TDCI. (most common european denomination, different in UK and probably Ireland)
Hello,
thanks for this video, It was helpful, but worse is to change the pollen filter on european version (steering whell and gas pedal on the left side ... )
Screw things back by hand as much as possible to avoid stripping any threads, thought it was best to change oil when hot, on some car makes be careful not to let oil from filter drip on to clutch, best let used oil drip out of pan a while, new plug and washer an idea, turn engine few times after changing oil before starting is an idea too.
Great video Nigel I was trying to film my service recently but had to stop halfway due to the weather! Did you have any oil leak from the sump plug, the copper washer is crushable one on my 2009 mk4 Cheers
You should change the washer each time.
No need to remove the glove box. Just drop down the fuse tray. Also, remove the oil filter before refitting the drain plug, more old oil will drain away.
I take the filter out first or when the sumpplug is still out
best like
Good videos Nigel, one question, I've found that the oil filter plastic nut is cracked so I can't apply any torque to remove it, any thoughts on how to get it off?
Hi Clint.
Thanks for watching. The cap needs replacing either way so I wouldn’t worry about breaking it. They are cheap enough OIL FILTER HOUSING TOP COVER CAP WITH SEAL www.amazon.co.uk/dp/B077NG9PSH/ref=cm_sw_r_cp_api_glc_fabc_EQ4548EWPT4JDE97R9PM?_encoding=UTF8&psc=1
I would suggest either buying a belt wrench like this Baby Boa Strap Wrench - Colour May Vary www.amazon.co.uk/dp/B00096JDJY/ref=cm_sw_r_cp_api_glc_fabc_5RN27QK0HW2ZTTMM3P39. Or create something using a strap, cloth or string.
You could also try banging a screwdriver through the side of the cap to help open.
Hope this helps.
Hi Nigel, just wanted to ask in case you know. I have the exact same car as this with the same sump plug. It needs an allen key just like yours and it stripped out, no doubt from the last service of which i didn't do. Would you have any information on how to determine the specs of the plug itself? I only ask since I went to my local car shop and they only had plugs for the 1.8 with the hex rather than the allen key. Any help would be great, cheers.
I sympathise as my sump plug is also wearing and will be replaced on the next service. I found this on talk ford talkford.com/community/topic/386513-sump-plug/. It doesn’t matter whether you replace with hex or Allen or Torx provided the thread is right. Phone Fords and see how much they will sell one to you but get the part number out of them and then check Halfords and Amazon.
Hi NigelGreat VideosI have the same Mondeo what specific tool is needed to remove the oil/drain plug as I need to purchase the correct one to remove it.Thanks again Steve Sydney Australia
+Steve Lemonis Hi Steve its just an Allen Key. I can't remember what size it is as I have a set of them that I use with a socket set adapter.
Could you do a separate video please on where to use trolley jack and axle stands safely on the Mondeo Mk4
There are plenty of videos already on TH-cam showing how to jack the car. This one is a good example. th-cam.com/video/bhdFrfNcHP0/w-d-xo.html
I always use axle stands and a trolley jack for safety rather than the car’s supplied jack. To stop the car rolling I put a brick either side of at least one wheel that will stay on the ground. In addition I use the handbrake if jacking the front or put it into first gear if jacking the rear.
hello j have mondeo mk4 2007year 2.0tdci 96kw automatic gearbox
j like change oil on gearbox please give me some information thanks!!
Nice vid can u tell what size allen key for sump plug please . G
Look at my toolbox this morning I'm pretty sure I used the 8mm
what is the socket size and allen key size to remove sump plug?
I think I used the 8mm Allen
Looks like you changed a carbon impregnated odour / pollen filter with just a pollen filter. The colour of a new odour / pollen filter is dark grey not white.
Is that the only oil filter, because when I bought the set from eBay it came with a metal sealed screw on type as well.
thats the fuel filter
hi great video are you planning a glow plug video
Rossmc1984 only if mine crap out
Hi, would you mind letting me know exact trolly jack and axle stand locations you used.. I have the same car but want to double check. Good video Cheers
Use some bricks around the front wheel if jacking the rear, or apply the handbrake for jacking the front, either way make sure it won’t roll. I jack up under the sills. You will find indentations in the sills just before the wheel arches, these are the jacking points. Jack up the car and then put in the axle stand. Lower the car gently until it rests on the stand. If the jack is not in the way leave it in position sharing the load for better safety. If you search the Internet you will find pictures showing the various mondeo models’ jacking points.
Nigel Ealand thank you for the reply I’m ok with the jacking location on the sill, are you placing your stands just to the rear of this spot.. ie in line with jack but towards rear of car? Thanks again
hello, mondeo 2008 diesel aisin af40 gearbox does not have any internal problems in normal driving, but sometimes when I slow down, for example, when I slow down while approaching the red light, the car gets a slight knock when it goes to idle. Sometimes it happens once a day, sometimes it happens several times a day. Is there a solution you would recommend without opening the gearbox? What could be the source of the problem. I live in Turkey and the prices are very high due to economic conditions here, can I solve it at low cost? Thank you in advance
(transmission oil changed 1000 km ago but not improved)
I would suggest using a OBD2 interface and download Forscan. Scan the car and see if you have any error codes.
Hi, do we need special tools to change the timebelt of ford mondeo. Thanks
Yes you do. One to lock the camshaft and the other to lock the flywheel at TDC.
mate how do u go about resetting the message on the dah that say change/service oil?
That's in the video description. Have a look at this th-cam.com/video/8_12A1Vz3b0/w-d-xo.html
Would there be any negative effect from leaving the undertray off? It adds about 1/2 hour to the job.
It’s there to keep the engine compartment clean from the road muck and that would impact.
Hi I have a kuga with the same engine 2.0 tdci and I have a problem with black smoke from 3000rpm up when u accelerating drive normally it doesn’t smoke and there’s a whistling noise when you let of the throttle any ideas what it could be no engine light ether
Hard to say. I think I would start by looking at the EGR valve. It recirculates the exhaust gas to clean up the burn. If the car has been doing a lot of local slow driving it can get coked up. I did one once on a mk3 Mondeo. It was easy to get off and I used some spray Carb/EGR cleaner. Do a search on here to find out more.
have you done transmission oil cahnge? does it have a transmission oil dip stick?
I haven’t done one on that car but there is no dip stick. To drain and refill to the correct level there is a drain and separate filler / level plugs. The automatic, 5 speed and 6 speed gearboxes are all different. Buy a manual to see the correct procedure for you car. Thanks for watching.
thanks. appreciate your reply.@@NigelEaland
Give the tool sizes in the future
How's 2013 different?
Hi mate I got my mondeo mark 4 done yesterday as it was saying service oil on the dash it cost me £160 to be done but as I’m driving it now it’s loosing power have you got any advice or do you know if he’s actually done the job correctly thank you
I assume we are talking Diesel engine? Since it’s just been service the obvious thing to check is air in the fuel line. This is caused by the fuel filter housing bleed valve has not been tightened after the filter was changed. To see if this is the case look at the clear plastic fuel pipes under the bonnet for air bubbles. If they are there then slide under the car with a spanner and check the filter housing.
The alternative is sending it back to the garage and complain.
Good luck and thanks for watching.
Wht abt transmission oil ..n hw to chk transmission fluid level since there is no dip stick to check transmission fluid
You need to read the manual. For a manual gearbox the correct oil level is when it is filled enough that it start to trickle out of the filler hole.
Hello Sir from Vietnam!
I have just owned Ford Mondeo - Gas A95 version for Vienam market 2009, I have an issue with my smart key fob, hope that you may help me to fix its.
I couldn't use the Open button to open the door even when I press that button the connected between smart key & car.
Thanks
Have at my fob battery change and programming video it may help. th-cam.com/video/PdeqeD8YhvE/w-d-xo.html
Have you ever changed the gearbox oil?
Changing the gearbox oil is not normally a service requirement. It only gets done if the gearbox Is overhauled or as precaution if the vehicle is high mileage and had a tough life. To get to the drain plug you need to remove the front left wheel and the plastic wheel arch cover. The manual says there is a drain plug at the bottom on the right side of the five speed manual box or on the left of the six speed. Just above the drain is the filler plug. Fill the box until oil over flows the filler.
hi nigel, can u show me the DPF on 2007 tdci mondeo where is located and is there any indication on the dash or else where on the car?
I dont know my 2007 tdci mondeo has one or not please help.ASAP.
It has but I have never changed one. Follow the exhaust pipe down from the engine and it will be the first box you find. They are very expensive to replace but there is apparently a method of regenerating (cleaning) them. You need to get the DPF really hot by driving down a motorway in 3rd gear with over 2500 revs. The other thing to look at is whether the EGR valve is coked up. You can take the EGR off and clean it with carburetor cleaner. On the 2007 I think it is right at the front on the left side of the engine.
This video explains this stuff really well. th-cam.com/video/yzRR8BTVsyw/w-d-xo.html
Nigel Ealand i dont have any problems with the DPF but I just want to find out if my car has a DPF or not. Is there any other way than to follow the exhaust pipe to figure it out.. I have checked around and some 2007 models have a DPF while others dont. I wanted to know because i have to change the oil of the car and if it does have DPF then i will use DPF safe oil. Are there any indicators or warning signs on the dashboard that will show if i have a DPF.
Thanks
MR. TES if you go to a parts shop they can normally look up your registration number and check whether you have a DPF and make sure you have the right oil.
What a nightmare only to change the pollen filter. I change mine in less than 2 minutes on a Citroen C4.
what size is the socket to remove them oil filter?
Matthew McKenzie 27mm
Where is the best location to place jack stands underneath the mk4 Mondeo?
Ben Ho put the jack on the sill seam. You should see a slight indent on the seam, this is the jacking point. I always put an axle stand in beside the jack to protect me in case of jack failure. Have a look at this www.talkford.com/community/page/fordwiki/fordwiki.html/_/mondeo/mondeo-mk3/jacking-points-r127
Nigel Ealand thanks, I've been meaning to rotate the front and rear tyres so they have even wear. I'll be trying this out. 👍
While the sum plug is out.
Why didn't you change fuel filter at the same time ??
I did that as a separate video. You will see that at the time I wasn't sure how to prime the fuel line after the change. Rather than rush the job I did a bit of research and then had a go. Check my other video.
Stupid pollen&oil filter position. Thank you ford
How many liter when changing an oil with the filter?
4.3ltrs of SAE 5w/30.
5.5 Ltrs. use FORD SPEC. 5w/30 fully synthetic.
Hi Marc. I'm not planning a flush but the description of how to do it is pretty the same as shown in this video of a Mazda.
th-cam.com/video/A0fiZCHz5ew/w-d-xo.html
There's also a description at TalkFord
www.talkford.com/community/topic/154556-power-steering-fluid-change/?p=1435677&hl=%20power%20%20steering%20%20fluid%20%20change&fromsearch=1#entry1435677
This is Ford engine or PSA Group? 😊
Ford.
Some of them are same as a transit engine
damn i got a problem with the Oil drain Screw. Cant open it cause the screw is damaged...cant fit any screwdiver or something else. Anyone an Idea ?
get an oil extractor, bought one today for €69 in a local motor factors, sucky sucky through the dipstick hole. The bonus being you will never have a leaky sump plug.
+Brian Galvin The sucky sucky job is the business only if you're sure you got all of the oil out. Any residue oil may contain gunk and sludge which will build up over successive sucky sucky jobs until you have caused major problems to your engine. Use PTFE tape on the sump plug for 100% reliable seal.
+Kevin Murphy tried that on a drippy plug once, didn't work. I do agree though that perhaps one in three oil changes should be of the old fashioned sort.
The plug head is just deep enough to get Mole or vice grips on and will remove easily. Buy a new plug from Ford, not expensive. Or better still, get a generic one off ebay - cheap - with a hex head instead of an allen screw, which was a stupid idea for a sump plug anyway.
that is one awkward pollen filter, my accord one is way more straightforward, no screws or anything, also the Mrs. golf is a breeze too, just a few thumbscrews.
I wouldn't put my mouth right under the sump plug whilst loosening it
Optical illusion it was nowhere near it.
@@NigelEaland Ah, I see. Nice video. I have the same car and I was thinking of doing an oil change.
@@russiandrivers9986 thanks. It’s a pretty straight forward job. Good luck and thanks for watching. Your comment made me laugh.
next time try without extension much easier...
Jesus... Poor Mondeo
I thought the MK4 mondeo was made up to 2014?
Well 2007 to 2010 2.0 TDCI 140bhp but after 2010 2.0 TDCI newer engine 116bhp 140bhp and 163bhp.
Hahaha 12:45
Much prefer a Honda child could service them.