You are always putting up good videos. I can't afford the IM608 so planning on buying IM508, do you think the IM508 can do this type of work since it doesn't have the j2534 interface.
Great video. Can you tell me please. Im trying to replace tcu but dont have orginal module anymore. If it says 2 yes and 2 no dose it mean its unlocked and if so can i install into the car? And than whats the next step?
On 06 Mercedes E320 CDI can I just replace the TCM if it shows fault with high end scanner or does it need to be programmed what if it comes from same year same model and has same numbers
Hello sir, i have a european model MB diesel hybrid (w212 2014). What diagnostic bi-directional tool you recommend. I'm from Europe. Thanks for the time you spend by helping other's.
@@BestCarFixes thanks for your time spended. What you think about the scanner tool Icarsoft cr pro multimark? I have 3 cars at home. But my MB212 will be the special scanner guest! What you say about. Ive notice you have a expensive one. I will say that isn't for me. I'm not an expertise like you are. So, chinese scanner probably they have plenty and probably these are all chinese manufactury from. Ive think my MB injection systems wasn't in the best conditions, bcz bad diesel. Already full the tank and put stp cleaner for tank and injection system. The OM651 motor noise are fine, but the gearbox isn't running normaly. Probably will need to restart it and run 10 miles to reeducate the 7G tronic transmission to my drive. But before I will need to reset the fault. I hope it is only bcz bad gás, and not ECR, HPFP or LPFP. That's why my needs. Thanks again for your time spended.
sir please help me i have nissan sunny 2010 Korean all key lost transponder chip ID 46..... outel 508 can program chips transponder by eprom data please ask me gave me information?
Hi I got autel im 508 and I would like to connect ism module from mercedes ml. Just quick question I found the diagram on autel without gbox use by obd the question is do I have to use xp400 then connect the pins from obd connector to ism module or just go directly without xp400?
The Dealer told me my car, 2004 ML350, can not be fixed. The AAM went out and is now obsolete. Does you know a work a round because these computer are specific to each car and you can not substitute used parts. Great body , tires, interior, I need help!? Question, is it possible to bet the ECM, AAModule, and Body controL (kEY) module from a like can with like number and re-install them in my can, WILL IT WORK. oH, YES, DO I NEED THE TRANSMISSION MODUEL ALSO. THE DEALER WILL NOT TOUCH ANY USED PARTS. THERE ARE NO MECHANICS IN THE DALLAS AREA WHO CAN HELP ME. WHERE ARE YOU , ANYWAY? WHAT WILL YOU CHARGED TO FLY TO DALLAS WITH YOUR TOOLS TO FIX CAR?
Hello, Is it possible with the help of AUTEL 608 PRO to Erase and Learning the Gearbox on Mercedes W212, 2015 , 722.996 VIN : WDD2120061B148466 ? Thank you.
Saya baru saja menurunkan tcu mercedes w245/B170 Dan saya menjumpai ada 2 jumper yg putus sehingga speed sensor /transmision failed contak workshop. Pertamyaanmya apakah setelah saya menyambung bagian yg putus tadi akan lamgsung normal ataukah butuh instal software
@@BestCarFixes tapi apakah fault2 tertera transmission consul workshop akan hilang dengan sendirinya... Setelah saua pasang semuanya... Tanpa programing
This video shows how you need experienced Mercedes techs with proper training to setup the modules. There's a dozen ways mistakes were made by repeatedly pressing the wrong options on the screen he says read and clicks write instead. Train wreck
You have a lot of patience with that man
I could not deal with a person like that screaming like crazy, great video thanks for sharing
Thanks for the visit
مبروك والله رافع راسنا يا هندسه
To me to you. Barry and Paul. Excellent 👍👍👍
Glad you enjoyed it
You are always putting up good videos. I can't afford the IM608 so planning on buying IM508, do you think the IM508 can do this type of work since it doesn't have the j2534 interface.
Yes the im508 can do this. I just verified on my im508. The j2534 is not needed for these IMMO functions.
Great video. Can you tell me please. Im trying to replace tcu but dont have orginal module anymore. If it says 2 yes and 2 no dose it mean its unlocked and if so can i install into the car?
And than whats the next step?
How it's work ? The original Vin number it's different from Vin which he told you !!!! 🤔
I found oil in the round connector that is outside ,is that a problem?
On 06 Mercedes E320 CDI can I just replace the TCM if it shows fault with high end scanner or does it need to be programmed what if it comes from same year same model and has same numbers
Hello sir, i have a european model MB diesel hybrid (w212 2014). What diagnostic bi-directional tool you recommend. I'm from Europe. Thanks for the time you spend by helping other's.
The best thing to do is to get mercedes a chines scanner one and play with it
@@BestCarFixes thanks for your time spended. What you think about the scanner tool Icarsoft cr pro multimark? I have 3 cars at home. But my MB212 will be the special scanner guest! What you say about. Ive notice you have a expensive one. I will say that isn't for me. I'm not an expertise like you are. So, chinese scanner probably they have plenty and probably these are all chinese manufactury from.
Ive think my MB injection systems wasn't in the best conditions, bcz bad diesel. Already full the tank and put stp cleaner for tank and injection system. The OM651 motor noise are fine, but the gearbox isn't running normaly. Probably will need to restart it and run 10 miles to reeducate the 7G tronic transmission to my drive.
But before I will need to reset the fault.
I hope it is only bcz bad gás, and not ECR, HPFP or LPFP. That's why my needs. Thanks again for your time spended.
Where are you based
Hello sir, Can the ms908s proii clone / write vin to vgs3nag2?? Or clone any of the vgs ???
The issue with the cable the can is backwards and it comes with 130ohm instead of 120.
sir please help me i have nissan sunny 2010 Korean all key lost transponder chip ID 46..... outel 508 can program chips transponder by eprom data please ask me gave me information?
I'm not sure but i think if you can read the data from immobilizer you can do that
@@BestCarFixes by the way IC?
Hi I got autel im 508 and I would like to connect ism module from mercedes ml. Just quick question I found the diagram on autel without gbox use by obd the question is do I have to use xp400 then connect the pins from obd connector to ism module or just go directly without xp400?
Don't need the xp400
will the autel ultra do the same????
Salut je voulais savoir esque autel im608 peut virginiser la boîte automatique de Mercedes 204
Yes
@@BestCarFixes OK merci Pour tout esque vous avez des vidéo de ça
@@BestCarFixessalut je peux avoir ton numéro merci
@@BestCarFixessalut comment va tu frère
Hello Mohammad I got a question where you got your connector cable? Or you made it by yourself?
you can do it yourself just put 120 ohm resistor between the can line
The Dealer told me my car, 2004 ML350, can not be fixed. The AAM went out and is now obsolete. Does you know a work a round because these computer are specific to each car and you can not substitute used parts. Great body , tires, interior, I need help!? Question, is it possible to bet the ECM, AAModule, and Body controL (kEY) module from a like can with like number and re-install them in my can, WILL IT WORK. oH, YES, DO I NEED THE TRANSMISSION MODUEL ALSO. THE DEALER WILL NOT TOUCH ANY USED PARTS. THERE ARE NO MECHANICS IN THE DALLAS AREA WHO CAN HELP ME. WHERE ARE YOU , ANYWAY?
WHAT WILL YOU CHARGED TO FLY TO DALLAS WITH YOUR TOOLS TO FIX CAR?
Big fan sir❤
هل يسوي نفس الشغل على رانج روفر سبورت 2017
What are the best tools you can recommend to me for ecu tcm verginaiz
use autel for right now
Can you show how you make that connection cable?
I would like to see your cable, mine is the same time you friend is having issues with
Hello, Is it possible with the help of AUTEL 608 PRO to Erase and Learning the Gearbox on Mercedes W212, 2015 , 722.996 VIN : WDD2120061B148466 ? Thank you.
Saya baru saja menurunkan tcu mercedes w245/B170 Dan saya menjumpai ada 2 jumper yg putus sehingga speed sensor /transmision failed contak workshop.
Pertamyaanmya apakah setelah saya menyambung bagian yg putus tadi akan lamgsung normal ataukah butuh instal software
No need programming
@@BestCarFixes tapi apakah fault2 tertera transmission consul workshop akan hilang dengan sendirinya...
Setelah saua pasang semuanya...
Tanpa programing
Salut merci pour la vidéo
Can my ms908 pro preform this ?
Yes
Assllamu alikum brother.
Nice
good information
الله يرحم والديك ويعطيك العافيه
ونبغك تشرح بالعربي جزاك الله خير
قريبا ان شاء الله
@@BestCarFixes أستاد الكريم ، الله يحفظك الشرح بالعربية كيف برمجة VGS بجهاز Autel ,اللهم إجعل هدا العمل في ميزان حسناتك 🤲
Hey will you be able to do mine
Sure call me at 3472281875
Can hi and can lo are reversed that's why cable can't read
الله يعطيك العافيه
لو سمحت نبغى الشرح بالعربي الله يرحم والديك
Vvdi bga good for mb
Is true
ليش ما تشرح بلعربي ؟ غريب
Ustat kolay gelsin lütfen türkce alt yazıda acın
Aslam wale kum
120 ohm
yes
This video shows how you need experienced Mercedes techs with proper training to setup the modules. There's a dozen ways mistakes were made by repeatedly pressing the wrong options on the screen he says read and clicks write instead. Train wreck
We have to start some where
The guy made same mistake of WRITING instead of READING on that first valve body. 🥸