Very nice video. Nice looking and functioning pistol grip and stock. I'm curious how this would hold up to hot desert temperatures of 110 degrees F. Thanks and looking forward to more videos and accessories. I'd like to see a vertical forward canted pistol grip that matches your pistol grip.
Noticed the note on the site about using sandpaper with v2 and v3. I have a v3 and it was stupid tight going on. Tank was down around 120 bar. Ended up lubing up with silicone oil and muscled it back off. Assuming with v2/v3 we have to remove some material? What grit paper is recommended?
There are some manufacturing tolerances with Huben tanks. Some forend slide right on and some are tight. You should not have to sand much material. I would use 400-600 grid. Use a pipe and wrap some sand paper on it and just remove a little bit of material. It should be a little tight so the forend does not move around once installed.
@@Bravo3d thanks And while here.. noticed theres two holes on top the stock.. could a cheek pad/riser of sorts be used? Currently i have a dove to pic adapter/rider with 1 adjustable scope ring .. angled down slightly. Running a reg dovetail ring my scope is maxed in elevation. Its actually great right now but a pad would be perfect.. might just make Something up DIY.
Say what you want about this kit, it’s some of the nicest looking 3d printed stuff I’ve seen. I have and love the Terminador stuff for my Avenge x but the quality of the print is no where close to this. Especially with larger parts.
I used a pill bottle with 600 grit paper around it and and removed some material. Still could not get the grip on. I will go at it some more and try again. Anybody else with v3 having troubles with it?
Should slide right on. Did you lower the pressure of the Huben down to around 2200 psi ? You can also use a blow dryer and warm up the place where the tank slides on. Does NOT need a lot of heat.
awesome looking stuff bro , i would love to see my ideas come to life with your expertise !!!
Thanks brother.
@@Bravo3d AND THANK YOU TOO BROTHER !
A very interesting video. I really like the Huben GK1
Gk1 is my favorite airgun, Semi auto and carbine stock is the best.
very beautiful, I have just ordered now 😀
Can you do some 3D print accessories for the EVANIX VIPER.. we also need a stock, picatinny mount, sight mount etc…
I would if I had one. I need to pick up a Viper. That would be turn it into a carbine.
Very nice video. Nice looking and functioning pistol grip and stock. I'm curious how this would hold up to hot desert temperatures of 110 degrees F. Thanks and looking forward to more videos and accessories. I'd like to see a vertical forward canted pistol grip that matches your pistol grip.
Thats a good question. The melt point of PETG is about 400F and starts to bend at about 200F. So if you can keep it away from 200F you should be okay.
Thats clean man props
Thanks bro. Check out my other video of the Huben Gk1
should the tank be expanding?
Noticed the note on the site about using sandpaper with v2 and v3. I have a v3 and it was stupid tight going on. Tank was down around 120 bar. Ended up lubing up with silicone oil and muscled it back off. Assuming with v2/v3 we have to remove some material? What grit paper is recommended?
There are some manufacturing tolerances with Huben tanks. Some forend slide right on and some are tight. You should not have to sand much material. I would use 400-600 grid. Use a pipe and wrap some sand paper on it and just remove a little bit of material. It should be a little tight so the forend does not move around once installed.
@@Bravo3d thanks
And while here.. noticed theres two holes on top the stock.. could a cheek pad/riser of sorts be used?
Currently i have a dove to pic adapter/rider with 1 adjustable scope ring .. angled down slightly. Running a reg dovetail ring my scope is maxed in elevation. Its actually great right now but a pad would be perfect.. might just make
Something up DIY.
Say what you want about this kit, it’s some of the nicest looking 3d printed stuff I’ve seen. I have and love the Terminador stuff for my Avenge x but the quality of the print is no where close to this. Especially with larger parts.
Thanks. I appreciate it.
I used a pill bottle with 600 grit paper around it and and removed some material. Still could not get the grip on. I will go at it some more and try again. Anybody else with v3 having troubles with it?
Should slide right on. Did you lower the pressure of the Huben down to around 2200 psi ? You can also use a blow dryer and warm up the place where the tank slides on. Does NOT need a lot of heat.
Wow!!!!!!!!!!!!!!!You Da Shiznit!!1
How much is that stock setup my friend.
Please check out Www.bravo3d.com for prices. Different kits have different prices.
Kool
check out my other video on the specs.
dope
Thanks
u dnt really need the hand gaurd piece
Nice