The TDA2030 is a monolithic integrated circuit in the Pentawatt® package, intended for use as a low frequency class-AB amplifier. Typically it provides 14 W output power (d = 0.5%) at 14 V/4 Ω. At ±14 V or 28 V, the guaranteed output power is 12 W on a 4 Ω load and 8 W on an 8 Ω (DIN45500). The TDA2030 provides high output current and has very low harmonic and crossover distortion. Furthermore, the device incorporates an original (and patented) short-circuit protection system comprising an arrangement for automatically limiting the dissipated power so as to keep the operating point of the output transistors within their safe operating range. A conventional thermal shutdown system is also included.
Basically TDA2030 has 14W output power capacity. You can upgrade the power by adding a pair PNP and NPN outputr transistor to increase current at lower load impedance. There's noway to upgrade the power capacity without those additional part. You didn't even measure the supply and output voltage to prove that you have upgraded it successfully.
It can handle up to 36 volts +18-0-18 using a center tap transformer and I would say with a 4 ohm speaker it will output about 16 watts and if you use a high output speaker like a 124 DB it might sound more like 25 Watts
The old TDA 2003 could actually handle 24 volts they use them in the old car stereos now note if you have an alternator that pushes 14 volts plus a battery and then if you had a backup battery that was 12 volts during the winter months it's nice to have cold crank lol🤓
знаете, мне грустно от того, в каком мире мы живем. то есть как бы никто не спорит что это работает, но никаких 100 ватт там и близко нет.если рассматривать видео как чувак сделал усилитель на коленке, то да круто(с учетом того что уже готовый модуль с распаяными компонентами и микрухой можно купить за копейки). а вот если задуматься, то можно понять, что нас просто обманули и никаких 100 ватт там нет даже с искажениями если брать.а грусно от того, что 2,3 тысячи человек поверили в видео и лайкнули.
Muito bom! Você fez uma coisa que ninguém faz: Mostrar a impedância a e watagem dos resistores. Muito importante saber a watagem dos resistores de carbono. Parabéns pelo projeto! Som roda redondinho.
Poor electronicist, you only chose to make the components that in Romania we had the TEHNIUM magazine that showed you everything to learn electronics and you could buy corroded amplifiers just to assemble them yourself, you could make high power speakers yourself...
it says 300W in the video, probably he have good sensitivity speaker and its have some excursion that some people sees and believes the 300watts of output power. I had the same mistakes as some peoples here. Novadays if i build a project amplifier, i do full measurement on the input and output and Q pins.
The TDA2030 is a monolithic integrated circuit in the Pentawatt® package, intended for use as a low frequency class-AB amplifier. Typically it provides 14 W output power (d = 0.5%) at 14 V/4 Ω. At ±14 V or 28 V, the guaranteed output power is 12 W on a 4 Ω load and 8 W on an 8 Ω (DIN45500). The TDA2030 provides high output current and has very low harmonic and crossover distortion. Furthermore, the device incorporates an original (and patented) short-circuit protection system comprising an arrangement for automatically limiting the dissipated power so as to keep the operating point of the output transistors within their safe operating range. A conventional thermal shutdown system is also included.
My Marshall guitar amplifier with a 6-in speaker has the TDA 2030 in it and Marshall used two of those jrc 4558d op amps as a drive stage. to push that chip. Most of the chips require some type of opamp to really get the full potential of output power of the TDA 2030 chip amp.
sore gan....bgmn caranya klo ditambahin kit mp3 bluetooth ( bikinin ya gan pleaseeeeee... ) smoga sll dpt insfirasi terbaru yg lebih baik dan sll sehat thank's
Hola buenas taredes Disculpa te hago una pregunta yo lo arme al circuito Pero dónde van conectados los parlantes me están saliendo 10 volt qué podrá ser
![เจ็บที่ยังฮัก - ม่อน วรวิทย์ [ Official Mv ] จอนนี่มิวสิค](http://i.ytimg.com/vi/KALIGSRSjFs/mqdefault.jpg)
*DIY Powerful Ultra Bass Amplifier 13005 Transistor from Broken Lamp , Simple Circuit , No IC **th-cam.com/video/_9UVNYeywKs/w-d-xo.html*
Try sound in speaker with box
Bagus sekali. Suaranya
The TDA2030 is a monolithic integrated circuit in the Pentawatt® package, intended for use as a low frequency class-AB amplifier. Typically it provides 14 W output power (d = 0.5%) at 14 V/4 Ω. At ±14 V or 28 V, the guaranteed output power is 12 W on a 4 Ω load and 8 W on an 8 Ω (DIN45500). The TDA2030 provides high output current and has very low harmonic and crossover distortion. Furthermore, the device incorporates an original (and patented) short-circuit protection system comprising an arrangement for automatically limiting the dissipated power so as to keep the operating point of the output transistors within their safe operating range. A conventional thermal shutdown system is also included.
🤔🍋
Potesio
TDA2030A 18W TDA2030 14W
Bu kısa devre koruma sistemi tda7056a da var
@@eik.casselbende a serisinden 7tane entegre var
Basically TDA2030 has 14W output power capacity. You can upgrade the power by adding a pair PNP and NPN outputr transistor to increase current at lower load impedance. There's noway to upgrade the power capacity without those additional part. You didn't even measure the supply and output voltage to prove that you have upgraded it successfully.
Betul
Itu klo pkek tegangan listrik langsung bsa gk
Me gustó la idea de poner otros transistores de este tda probare con 2n3055 buena idea ;p
Ang galing master mlinaw at mdaling sundan ang ginawa mo. Keep up the good work!
2030 cannot give more than 40 watt.please don't make us fool 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏.
eso es imposible que sea de 100 watts, pero bien por tu trabajo y tiempo.
I am from Indonesia, very impressed with the knowledge, genius, success, always my boss
terima kasih sudah berbagi ilmunya
Super! 👍
7:55 best speaker dancing ever 🤣👍
🤣🤣🤣
Sangat sangat bagus qualitas vidionya. Bravo. Juga audio ... Jelas dan terang semuanya. Thank, s.
It can handle up to 36 volts +18-0-18 using a center tap transformer and I would say with a 4 ohm speaker it will output about 16 watts and if you use a high output speaker like a 124 DB it might sound more like 25 Watts
Now building a low cost high performance aucdio amplifire is very much easy. Thank you very much sir...
Good design easy but good sound
Supar fenesen ❤️❤️❤️❤️
Chú thât tuệt vời nhất
Muy bueno los videos de los amplificadores de audio ,pueden mostrar un video de amplificador audio con el tda 1510q si se puede gracias.
😳🤔🙂 gracias por tu video saludos 🤝
The old TDA 2003 could actually handle 24 volts they use them in the old car stereos now note if you have an alternator that pushes 14 volts plus a battery and then if you had a backup battery that was 12 volts during the winter months it's nice to have cold crank lol🤓
Meaning 24 volts
I hope Chanel DIY will be more advanced & successful, great 🙏🙏🙏👍👍👍
Anh thợ điện, vui tính 😂
Bravo............Thaks you..
TDA2030 can only output 15w + 15w only, not 100w
Verygood.......
Output of tda2030 ic is max 14 watts, as per factory datasheet. Stop making false claims.
Muito bom gostei muito
Ваша пайка просто дивовижна...😲🤤
super
Good job
How can an audio chip for 14w to provide 300w without additional components?
Exelente, lo ise y suena genial
It's amazingly steady...
Super kreatif...mantaaab
знаете, мне грустно от того, в каком мире мы живем. то есть как бы никто не спорит что это работает, но никаких 100 ватт там и близко нет.если рассматривать видео как чувак сделал усилитель на коленке, то да круто(с учетом того что уже готовый модуль с распаяными компонентами и микрухой можно купить за копейки). а вот если задуматься, то можно понять, что нас просто обманули и никаких 100 ватт там нет даже с искажениями если брать.а грусно от того, что 2,3 тысячи человек поверили в видео и лайкнули.
Согласен. По даташиту тда2030 более 20в не вытягивает
Muito bom! Você fez uma coisa que ninguém faz: Mostrar a impedância a e watagem dos resistores. Muito importante saber a watagem dos resistores de carbono. Parabéns pelo projeto! Som roda redondinho.
5w
É tudo falso faz e vê se vai funcionar kkkkkk
ısınıyorsa waat lı kullanmalı
@@rogeriocosta4199 aaaaa niye ole dedin şimdi heves kalmadı bende
it cant be more than 15 watt according to ur diagram.
Мах 30 watt
Cool....
Ông nội Thợ Điện chứ đâu =))
Es conveniente que desacoples con un capacitor ese pobre altavoz, esta recibiendo tensión continua.
Eso como se hace, yo lo quiero hacer, pero dices que está mal, o que necesita un capacitor
Siiip 👍👍👍👍
Makasih jelas pemasanganya josss selamanya tyok Bantul jogya indonesia asia
Good
Please biid audio on Tda 2050 as shortly.
At least 28 volts DC to get that 12 Watts
Simpel dan keren
i cant stop says
''wow''
your work amaze me, thank you for sharing it
Nice
Đây là kênh anh thợ điện nha mn
Poor electronicist, you only chose to make the components that in Romania we had the TEHNIUM magazine that showed you everything to learn electronics and you could buy corroded amplifiers just to assemble them yourself, you could make high power speakers yourself...
Hi i did according to your video .music output sound not clear from speaker and tell me Dc supply?. 12 v and Amp
Nice 👍
Thanks for the project please show me how to put in the sound controls
But the chartsheet says tda 2030 can produce 14 watt of output so how will it produce 100 watt plz explain
Hahajahaaaa
hyaaayy lmaoooo
it says 300W in the video, probably he have good sensitivity speaker and its have some excursion that some people sees and believes the 300watts of output power. I had the same mistakes as some peoples here. Novadays if i build a project amplifier, i do full measurement on the input and output and Q pins.
And in order to get that 14 to 15 watts you at least need 13 volt center tap transformer 13-0-13
And of course it needs to be rectified full wave
Tda 2030 - 100w 😂😂😂
Cześć kolego po fachu sprubuj TDA 1514A z tego a będziesz wery chepi
Muantaaaappppp
This circuit technique is a half wave audio amplifier, provide higher Loud level but I don't know this fidelity result.
Yep, not a great or lasting way to use it for sure....
👌👌👌
300 w out of $2.50 cent chip wow🤣✌️ can I buy one from China?
Official datasheet : Max 30w
Technical DIY: 300w
🗿🗿🗿🗿🗿🗿
The TDA2030 is a monolithic integrated circuit in the Pentawatt® package, intended for use as a low frequency class-AB amplifier. Typically it provides 14 W output power (d = 0.5%) at 14 V/4 Ω. At ±14 V or 28 V, the guaranteed output power is 12 W on a 4 Ω load and 8 W on an 8 Ω (DIN45500). The TDA2030 provides high output current and has very low harmonic and crossover distortion. Furthermore, the device incorporates an original (and patented) short-circuit protection system comprising an arrangement for automatically limiting the dissipated power so as to keep the operating point of the output transistors within their safe operating range. A conventional thermal shutdown system is also included.
I can actually build amplifiers from the ground up the old school way
An opamp would definitely push it even harder like a jrc4558
My Marshall guitar amplifier with a 6-in speaker has the TDA 2030 in it and Marshall used two of those jrc 4558d op amps as a drive stage. to push that chip. Most of the chips require some type of opamp to really get the full potential of output power of the TDA 2030 chip amp.
funcionará con 4ohm?
Untuk ic tda 2050 apakah rakitanya sama atau berbeda?
Great
cara você e´ fera
Sir 1 video ya commnent mai bataye 4558ic ki jo output aa rahi hain who 2030ic ke konsi pin pe canect hai.....
Super 👍
Bro.aluminum ba yung kinabitan nyan?
Please can you help I was trying to make this Amp but It did work myb because of resistor the one I use it 5w0250J 🙏🙏 so tell me
Muito bom parabéns
Молодец.,схему ещё показать
wow
What is your using the camera recording this video.... really awesome 🙏👍🔥❤️
it can be supply with 5 volts?
Mantap
how many volts does this power have? from Indonesia
9-12V DC
sore gan....bgmn caranya klo ditambahin kit mp3 bluetooth ( bikinin ya gan pleaseeeeee... ) smoga sll dpt insfirasi terbaru yg lebih baik dan sll sehat thank's
Hello sir 7297ic ka video banae sir 4 din ke andar me
how to install a volume control bass and treble, and how to connect a additional speakers tnx
Sir instead of 5watt 100ohm how much watt and ohm can we used?
👍👍👍😲😲😲😲
Real amplifier is hidden
você arrasa qualquer técnico em eletrônica
Nenhum técnico é insuperável tiozão. Já mudei um amplificador de 3 em 1 antigo de 10w para mais de 100w. Tudo é estudo e prática.
kkkkkkkkkkkkkkkkk
Bang cobak buat amplifier 60w bass nya kencang dari tda 2030 bang
Sir, I made z44n circuit but it is not working.
let me know your problem ?
Sir, tell me to run it with electronic supply.
Sir no sound problem
Взагалі не зрозумів,живлення однополярне... Де вихідний конденсатор?
Автор видео походу не нашел даташит) и с его схемой там и 1го вата не будет
А ещё мне интересно зачем конденсатор между входом сигнала и питанием, это чтоб было больше искажений?)
Gostei do amplificador é muito bom ok professor
Maximum input voltage range
18-0-18 transformer at 3 Amper (max) current
Hola buenas taredes Disculpa te hago una pregunta yo lo arme al circuito Pero dónde van conectados los parlantes me están saliendo 10 volt qué podrá ser
Ami igual, quemé un parlante.
Maybe 300 W PMPO
Waw
Top em legal 👏
anh thợ điện kkk
Ok iwant to buy that kit sir
💯💯❤️❤️😎
perfect harika!!
Grandes proyectos
Anh thợ điện, kakaka
Kalau btl gmn rangkainya, salam sukses
Sya coba kk tda nya panas ya mas trs gk bunyi
Kalau buat ampli tda 2030 yg bagus dong cara videonya biar jelas di lihat gak kabur itu juga kalau rakit tdanya jangan yg rumit dong dan sebutkan resistor elconya berapa nomornya dong gitu
❤️❤️🔥 wow amazing
Bisakah rangkaian ini di buat setereo
More like 3 Watts with that 12 volt battery
Half wave audio too; thd 50%