If you are doing the second method, make sure that you remove the plastic part which holds the lock in place. otherwise the latch wont be able to open afterwards!!! You really should have mentioned this in the guide as most folks wont think about it
Nicely explained how to fix problem, my Washing had the same issue, I called Urban Clap, he asked Rs 1500 for repair, however I connected with IFB spars dealer and get the lock for Rs 300. and replaced on my own, now my washing machine started working fantasic , Thanks for on line video with out which difficult to replace
I want to say not only did this help me fix my WM spin cycle, but it is also a bit of art.. it is a rare thing to have something explained with such obvious enjoyment.
I have applied the 2nd option using a paper chip inside the door lock. After that machine is running. But the door is not opening. Tried after 1 hr also but still the door is not opening.. Kindly help with your suggestions. What is the next step to open the door.
thank you so much, i manage ( again ) to fix mine, wasn't same system ( much older ) but i managed to bypass with a bridge wire when i realise the dents ( pushed by the door lock ) were a bit loose. Like a "U" becoming slowly with time a "V" so i closed them slowly with a tool and off you go... ready for another 10years ! :D
In method 2, if you press the bi-metal down, you also press the pin down that locks the whole thing. So if the problem was that the machine stays locked, that method will not help. I took the little plastic pin from the bi-metal to fix that.
Dear brother... thanks for such nice explanation with video..as per this video, shorted phase with common. Machine working fine & program also run successfully. My machne is IFB front load ,Senorita DX 5.5kg model. After succesful completion of progeamme, what are the front panel LED light conditions. My machone showing , Door - red Led continuous glowing, Active Led geen color blinking
thanks Good one! it would be more safe to use the original plug to prevent any wire lose cause it is high current. then 1. to remove the heating power pin; 2. it is necessary to remove the door lock plastic tab to allow the door can be opened
Hello, I need your help. I bypassed the switch just by adding some thick tape inside the internal part of switch to remain pressed and make contact all the time. I did not remove the thermal sensor nor the spring mechanism. Now the door is permanently locked and unable to open😅. Even when i try mechanical force bypass by pressing the lock with haxo blade it doesnt work. Please guide to solve this thanks
Thanks a lot for this video. Ton of help. If you have got a Samsung machine it might work for you as well. Just connect the blue with the two black wires and leave the red one out.
I njoyed the video... thanks a ton... I replaced with a new one and issue for starting the machine is closed... but I am not able to open the door after wash as the led displays.. so I switch off power after couple of minutes I am opening... what for I am not able to open door upon completion of washing
when machine working the small heater inside the switch is on and it will heat the bimettallic strip and it expands. this metallic strip pushes a plastic piece close to your door knob which prevent the door to open. when switch off the heater getting off and so the bimettalic strip cools down and pull back the locking plastic. thats how it works.
@@MeetMyIdeas door interlock switch will give command to start the machine. My machine led for door was blinking, so I replaced the door limit interlock switch, now no led indication machine is working fine.. after completion of washing door led starts blinking.. how to rectify it. I am not able to open the machine after completion of washing...
Thanks for the video. I am also facing a similar issue. I replaced the old lock with new one. Now, after completing wash cycle, the door led and error led keeps blinking and I am unable to open the door even though the washing is complete. I need to trun off power and wait for some time, then the lock gets released and door can be opened. With the original switch, the door lock would get released automatically aftwe wash cycle is complete.
Hi, In our IFB washing machine front door lock phase voltage is only 60, so its unable to generate sufficient heat and lock is not working. Please let me know how to check and fix the phase voltage. Thanks.
Hello sir after using this door lock setting, now next process doesn't start I mean screen stuck at "door locked and child lock available" status. Please guide me what to do?
@@opiritetariah If you use 2nd method, you will need to remove the small plastic rectangular block inside the switch which locks the door once the machine is switched on. If this is not removed, you will not be able to unlock the door again. The disadvantage is that the door can be opened even when the machine is running, so there is no safety. Better to put a new switch as soon as possible.
I have applied the 2nd option using a paper chip inside the door lock. After that machine is running. But the door is not opening. Tried after 1 hr also but still the door is not opening. Tried from opening the top of the machine also but could'nt able to do so. Kindly help with your suggestions. What is the next step to open the door. .
For the door to open the common & phase has to be disconnected. The method illustrated in the video can be used to verify a faulty door switch. Not to repair the switch rather.
@@ThePlatformTV100 Thanks! makes sense (The method illustrated in the video can be used to verify a faulty door switch) Verify and go and purchase a new door switch and replace it. While buying go with the older one to get same model.
@@safirab9436 idk...this method didn't work for me...the door got locked but the washing machine won't even start.. Btw for ur case it should probably open just by cutting the main switch..
@@abhichi then your problem is probably from the dashboard... It did not open at all I had to open the upper part and break the interlock..... By doing that, the problem got shifted to the dashboard as the safety key stopped working..... Had to call someone to fix it.... Sad life
If the door open Push the plastic lock( plastic between the front and back layer of switch which is movable by pushing) in between to right. if door closed open top cover and push the lock. to open the top cover see th-cam.com/video/fY9MSttelbY/w-d-xo.html
in second method when the bimetallic strip expands a small plastic lock moves and lock the door. when bimetallic it cools it may go back. if not you have to push back the sliding plastic lock with screw driver. if not accessible from front need to open the top cover. to open top cover see th-cam.com/video/fY9MSttelbY/w-d-xo.html
hello sir good day to you.if you said lecture it will be better than this music.ok anyhave i have doubt? that which two point are jumpered?common and neutral?
when you bypass keep the locking (holding) portion of the door switch in the same place. Jam the sliding/moving plastic in side the switch which prevent the door open after wash
Please don't do this!!! Very dangerous especially if there are kids around . Never work on an appliance whilst power going through it. It can kill you. And never bypass safety features. There is a risk of fire, electric shock, or in this case with the door lock, if the door is opened during a spin, it can pull kids' arms inside and cause degloving, multiple fractures or even worse...amputation !!! Instead, replace the door lock completely. If you are not confident carrying out the work, pay a professional because it will guarantee safety and piece of mind. There is a reason they charge what they do, it's because the know how to repair your appliance properly and safely. There are far more risks thank non professionals are aware of. Please be safe , especially if you have kids!
@@whirlpool_addict_ yes I was aware of this but thanks for bringing my attention to it . I don’t have children . But the people who attempt this at home after watching may have children.
![ปฏิเสธไม่ไหว (Crush on you) - LIPTA feat. No One Else [Official MV]](http://i.ytimg.com/vi/NBw1jF342vw/mqdefault.jpg)
This video saved my 22 year old washing machine from being scrapped. Very happy. Many thanks from London UK.
welcome to my world :D
If you are doing the second method, make sure that you remove the plastic part which holds the lock in place. otherwise the latch wont be able to open afterwards!!! You really should have mentioned this in the guide as most folks wont think about it
Nicely explained how to fix problem, my Washing had the same issue, I called Urban Clap, he asked Rs 1500 for repair, however I connected with IFB spars dealer and get the lock for Rs 300. and replaced on my own, now my washing machine started working fantasic , Thanks for on line video with out which difficult to replace
Hey can you give no. Of IFB dealer
Very useful. Saved me time n money. Service centre told me PCB needs repair along with switch
Thank you very much. I bypassed the switch now my washing machine is running fine. Your video is so helpful..
I want to say not only did this help me fix my WM spin cycle, but it is also a bit of art.. it is a rare thing to have something explained with such obvious enjoyment.
Thanks for the lovely review
I have applied the 2nd option using a paper chip inside the door lock. After that machine is running. But the door is not opening. Tried after 1 hr also but still the door is not opening.. Kindly help with your suggestions. What is the next step to open the door.
Thanks the customer service centers charge ten times of the actual cost this saved me so much of my hard earned money
Very good vid thankyou. new door lock ordered. Saved my machine from junk yard😃
Very well explained...I changed lock twice but nothing worked as this simple Tip.
Thanks for the detail video I am able to dispone the switch issue properly and will replace the switch
Thanks again
thank you so much, i manage ( again ) to fix mine, wasn't same system ( much older ) but i managed to bypass with a bridge wire when i realise the dents ( pushed by the door lock ) were a bit loose. Like a "U" becoming slowly with time a "V" so i closed them slowly with a tool and off you go... ready for another 10years ! :D
In method 2, if you press the bi-metal down, you also press the pin down that locks the whole thing. So if the problem was that the machine stays locked, that method will not help. I took the little plastic pin from the bi-metal to fix that.
Doesn't bypassing switch burns main board of machine!!
Thank you so much!!! It is works in my IFB washing machine!!! Is any problem water into circuit and pass shock in the entire machine?
Dear brother... thanks for such nice explanation with video..as per this video, shorted phase with common. Machine working fine & program also run successfully. My machne is IFB front load ,Senorita DX 5.5kg model. After succesful completion of progeamme, what are the front panel LED light conditions. My machone showing , Door - red Led continuous glowing, Active Led geen color blinking
When I am shutting door hard then it's getting locked & machine starts,
Should I changed door switch ?
Thank you very much to this useful video. I will done through your video without any payment. Thanks again
Glad it helped u . Keep watching the channel for more videos like this .
thanks Good one! it would be more safe to use the original plug to prevent any wire lose cause it is high current. then 1. to remove the heating power pin; 2. it is necessary to remove the door lock plastic tab to allow the door can be opened
Thank you very much.
Helped me a lot.working fine now
Excellent video. Clear and comprehensive.
Hello, I need your help. I bypassed the switch just by adding some thick tape inside the internal part of switch to remain pressed and make contact all the time. I did not remove the thermal sensor nor the spring mechanism. Now the door is permanently locked and unable to open😅. Even when i try mechanical force bypass by pressing the lock with haxo blade it doesnt work. Please guide to solve this thanks
Thank you sir, it is a very useful video, I managed to run my washing machine in which the door was faulty, using ur video🙏
Wow. It worked 🙏 thank you so much 👍👍👍👍👍👍👍👍🙏🙏🙏🙏🙏🙏🙏
Thanks a lot for this video. Ton of help. If you have got a Samsung machine it might work for you as well. Just connect the blue with the two black wires and leave the red one out.
I njoyed the video... thanks a ton... I replaced with a new one and issue for starting the machine is closed... but I am not able to open the door after wash as the led displays.. so I switch off power after couple of minutes I am opening... what for I am not able to open door upon completion of washing
when machine working the small heater inside the switch is on and it will heat the bimettallic strip and it expands. this metallic strip pushes a plastic piece close to your door knob which prevent the door to open. when switch off the heater getting off and so the bimettalic strip cools down and pull back the locking plastic. thats how it works.
@@MeetMyIdeas door interlock switch will give command to start the machine. My machine led for door was blinking, so I replaced the door limit interlock switch, now no led indication machine is working fine.. after completion of washing door led starts blinking.. how to rectify it. I am not able to open the machine after completion of washing...
Thanks for the video. I am also facing a similar issue. I replaced the old lock with new one. Now, after completing wash cycle, the door led and error led keeps blinking and I am unable to open the door even though the washing is complete. I need to trun off power and wait for some time, then the lock gets released and door can be opened.
With the original switch, the door lock would get released automatically aftwe wash cycle is complete.
My washer has wet laundry and it started door lock. How do I fix
After bypassing the door switch it's not taking water not draining water. It only spins. It was doing that before switch "de" error.
How to reseal the door rubber
Please reply
Can we reseal using the same steel wire which we removed?
Yes we can!
Hello sit I used your idea and bypass switch but after that water is not filling in washer it going direct to drain.
Sir main also same machine after taking water, not spinning Pls help me what to do.
Did that ,now. It never stops 😂 ,keeps on working on loop even after going to the stop sign 😂
Thanks for videos
Please make about videos front load washing machine wiring how to tracing
Sir
Hi, In our IFB washing machine front door lock phase voltage is only 60, so its unable to generate sufficient heat and lock is not working. Please let me know how to check and fix the phase voltage. Thanks.
Same problem.
What solution did you find. 9888555456. Whatsapp me
Can you use a multimeter if you don’t have one of them test pen/light
hi! what if 2 out of 3 light up the tester?
Very well explained - thanks!
Method 2 is much safer bet - avoiding playing with live wires :)
Nice explanation,thank you sir
The best explanation 👌
O ysssssssssssss
Gooooooooooda 🎉
Perfect 👌
nice, thankyou
Great!!! It’s works!!!!
super sir
Tysm I repaired my washing machine!!! You’re amazing
Super 👌
Hello sir I have ifb front load aqua VX. I have replaced the door switch.. still machine door not locking. Please help..
Same problem for my washing machine....
Call to this number 7200794809
Safe po ba
I wish the video recording was more steady and precise. Other wise it was informative
how to jump with 4 wires plug. LG wash machine model WM4270HVA
Hello sir after using this door lock setting, now next process doesn't start I mean screen stuck at "door locked and child lock available" status. Please guide me what to do?
😂😂💔 I was expecting this, let me guess, you used the second method right.. how did you fix it?
@@opiritetariah If you use 2nd method, you will need to remove the small plastic rectangular block inside the switch which locks the door once the machine is switched on. If this is not removed, you will not be able to unlock the door again. The disadvantage is that the door can be opened even when the machine is running, so there is no safety. Better to put a new switch as soon as possible.
Thank god! I was about to try second method - Thanks for the tip M V !
Great sir
Nice... thks
I have applied the 2nd option using a paper chip inside the door lock. After that machine is running. But the door is not opening. Tried after 1 hr also but still the door is not opening.
Tried from opening the top of the machine also but could'nt able to do so.
Kindly help with your suggestions. What is the next step to open the door. .
For the door to open the common & phase has to be disconnected.
The method illustrated in the video can be used to verify a faulty door switch. Not to repair the switch rather.
@@ThePlatformTV100 Thanks!
makes sense (The method illustrated in the video can be used to verify a faulty door switch)
Verify and go and purchase a new door switch and replace it.
While buying go with the older one to get same model.
Thanks very much! It worked for my washer.
Hello sir..is it safe to use plastic or paper inside door lock switch..method 2???
Well it works for closing it but now how to open it after it washes....
@@safirab9436 idk...this method didn't work for me...the door got locked but the washing machine won't even start..
Btw for ur case it should probably open just by cutting the main switch..
@@abhichi then your problem is probably from the dashboard... It did not open at all I had to open the upper part and break the interlock..... By doing that, the problem got shifted to the dashboard as the safety key stopped working.....
Had to call someone to fix it....
Sad life
Hello sir
the door is in lock position after bypassing the switch. how to open the door?
If the door open Push the plastic lock( plastic between the front and back layer of switch which is movable by pushing) in between to right. if door closed open top cover and push the lock. to open the top cover see th-cam.com/video/fY9MSttelbY/w-d-xo.html
Nicely done and useful as well
Same machine, double phase coming in door lock connection.
Neutral doesn’t need to be connected?
Thanks very much! We have just fixed ours today. The wash machine now is running again. Feel great!
Bro door lock hone ke bad khule gaa kaise?
Thank u
Hi I do the second bypass technique.. after washing door is not opening .. what should I need do
Please reply any solution for this
in second method when the bimetallic strip expands a small plastic lock moves and lock the door. when bimetallic it cools it may go back. if not you have to push back the sliding plastic lock with screw driver. if not accessible from front need to open the top cover. to open top cover see th-cam.com/video/fY9MSttelbY/w-d-xo.html
@@MeetMyIdeas
But I put a piece off paper inside.. to.contact .. sorry I mean the last method i did
Front door stuck now. Only chance to do anything inside using top open
Could you please give your contact number if possible
What if three lines reading live with test screw
Seems to be some problem with PCB then...😢
Thankyou thankyou thankyou :):):)
Sir my door lock switch new one change radey but again door error come what problem sir
Main pcb most likely
Ifb 5.5kg front load washer door light is blinking, don't know to solve the problem
open the drain and remove the water inside and restart it may work
How many times blinking
How many times blinking,count carefully, I will explain u r washing machine problem...
Good
Nice 👌
Thanks Bro😊
I have 4 pins
hello sir good day to you.if you said lecture it will be better than this music.ok anyhave i have doubt? that which two point are jumpered?common and neutral?
भाई आपन मोबाइल नंबर
My washer door won't stay shut so it won't work
when you bypass keep the locking (holding) portion of the door switch in the same place. Jam the sliding/moving plastic in side the switch which prevent the door open after wash
Please don't do this!!!
Very dangerous especially if there are kids around .
Never work on an appliance whilst power going through it. It can kill you.
And never bypass safety features.
There is a risk of fire, electric shock, or in this case with the door lock, if the door is opened during a spin, it can pull kids' arms inside and cause degloving, multiple fractures or even worse...amputation !!!
Instead, replace the door lock completely. If you are not confident carrying out the work, pay a professional because it will guarantee safety and piece of mind.
There is a reason they charge what they do, it's because the know how to repair your appliance properly and safely. There are far more risks thank non professionals are aware of.
Please be safe , especially if you have kids!
@Jamie Dow, you know, you can leave the door closed and maybe supervise your children if you have!!!
@@whirlpool_addict_ yes I was aware of this but thanks for bringing my attention to it .
I don’t have children . But the people who attempt this at home after watching may have children.
@@JimmiG585 Oh ok no problem and stay cautious if you do this!
@@whirlpool_addict_ I’m glad we agree
@@JimmiG585 Also be VERY Careful when playing with the interlock wires.When the machine starts the cycle, MAINS VOLTAGE pass through the cable.