I did this last night. I found some old harden grease and a little bit of red dirt in there. The contacts were dirty. Cleaned them and the headlight started working again. Thanks again.
Thanks for the video, feels like I have the same issue. When I push the starter button it begins to start. But not every time. Definitely feels like it's the switch.
Thanks, Hope this resolves my issue- bike starts but starter keeps trying to start the bike. Kill switch doesn't stop engine- nor does key. Suggestions?
@@lstruggy hey, I would suggest disconnecting the battery as a safety precaution but we didn't. We just used a shop towel to wipe the contact grease off then used electrical spray cleaning to clean it better. Then we close her up and she worked like a charm. Till this day we have yet needed to replace a start button on a Honda with this issue. Good luck 👍
Hey, it's a good question actually, not everyone aware of what can be used on internal parts. Cleaning the shavings out we just shook out as much as we could then used forced air for the rest. We use wd40 alot to clean oil contacted surfaces. It breaks it down pretty good and wipes off well and it don't hurt o rings are rubber gaskets. Hope this hopes. Reach out anytime 👍 #RideSafe
All my light working but i hav to still start with my screwdriver should i do wat you do an try again ? I uqv to boost my bick an after my switch not working grrr. Thankyou !
I did this last night. I found some old harden grease and a little bit of red dirt in there. The contacts were dirty. Cleaned them and the headlight started working again. Thanks again.
Awesome. You're welcome
Thank you for this information and the video. It just got my husband off the side of the road.
You're welcome. Glad to know it helped 👌👌
Best video on here....
You saved me money...
Thanks brother
Awesome. You're welcome, Glad it helped. Besafe out there on 2s
You're awesome! Gonna tear this apart on my next off days!
Thanks. Good luck 👍
Thanks for the video, feels like I have the same issue. When I push the starter button it begins to start. But not every time. Definitely feels like it's the switch.
You're welcome. Sounds like the symptoms of dirty contacts points. Give it good clean and see if it helps. Good luck 👍
Worked like a charm.. thanks again
@@kevinhagen8829 awesome. Good go. You're welcome. #RideSafe 👌
GREAT VIDEO!
@@marksundstrom1329 Thanks
Thanks, Hope this resolves my issue- bike starts but starter keeps trying to start the bike. Kill switch doesn't stop engine- nor does key. Suggestions?
Hey, sounds like your starter relay is bad. It's continuing to hold contact even after you release the button. Replace your starter relay. Good luck 👍
Thanks buddy I'm up next
@@Mojo27564 you're welcome. Good luck 👍
Awesome video thank you for the help
You're welcome.
@@Gordons-Cycle-Parts do I have to unplug the battery before I open the ignition case and what did u use to clean it towel scotch brite pad?
@@lstruggy hey, I would suggest disconnecting the battery as a safety precaution but we didn't. We just used a shop towel to wipe the contact grease off then used electrical spray cleaning to clean it better. Then we close her up and she worked like a charm. Till this day we have yet needed to replace a start button on a Honda with this issue. Good luck 👍
@@Gordons-Cycle-Parts Tnx for the reply sir am getting ready to tackle this today 🤞🏽
@@lstruggy you're welcome, you got this 💪 good luck
Dumb question but what did you use to clean everything up? Any certain product or steel wool type of stuff? Thanks!
Hey, it's a good question actually, not everyone aware of what can be used on internal parts. Cleaning the shavings out we just shook out as much as we could then used forced air for the rest. We use wd40 alot to clean oil contacted surfaces. It breaks it down pretty good and wipes off well and it don't hurt o rings are rubber gaskets. Hope this hopes. Reach out anytime 👍 #RideSafe
There is also product for electronic contact cleaners same stuff I use for the internal parts of my rc motors
Your good man are you around san antonio texas
We're in O'Fallon IL which is the St Louis Missouri area.
Thanks
@@chuckspeer2163 you're welcome
All my light working but i hav to still start with my screwdriver should i do wat you do an try again ? I uqv to boost my bick an after my switch not working grrr. Thankyou !
Yes, I would clean the contact points off. High chance it's not making contact do to build up. Good luck 👍
How do you get the switch out of the lower casing? I don't want to break the switch. Thank you
Remove the screw that's holding it in place
@@Gordons-Cycle-Parts lol
@@marksundstrom1329 I mean 🤷
sweet !!!!!
TY!!!
You're welcome
Every time you cut off the camera it should be on!
Cleaning r
Ti
Not sure what you're asking