After the setup processes the Home base can be set to operate over WiFi, letting you place it a little better then if it had to be connected to Ethernet.
I've seen a video where it's said that when the homebase is connected to WiFi, it won't record 24/7 feeds, just clips (like motion detected event etc.) is it true ?
I am planning to buy eufy cam 3 4k. I want to install one outside and one inside the house. Will ot work the one inside the house ? Even there is no sunlight direct to the solar panel.
I just received our new home base 3 we currently have a home base 2 with 3 cam2 cameras currently working. Do i have to take them all down and hold them near the new home base 3 and reinstall them again?
Hi i have a old eufywireless doorcam 2k after i changed broadband now my chime cannot sync to the doorbell cam. I want to ask if i buy the homebase 3 that i can connect that to my doorbell cam and then have my echo 8 as a chime
I know this might be making this very simple but when you changed broadband providers did they use the same wifi name and password you had setup before?
@@Wanderer001_Reviews_Clips No all the details of username and password was changed so I removed the doorbell and chime from the eufy app then when I tried to set it up again on the new broadband the doorbell does not syc to the chime anymore
@@Choco_kitty35Did you get a new wifi access point? Might need to try moving it closer to it durning setup. I know I have used a few things like that in the past that needed to almost be right on top of my old setup.
So I have a mesh network which covers the whole house and my outdoor patio. However, when I do the setup, it wants it to connect to the router Wi-Fi. After I do that, I cannot connect my additional cameras to the hub unless they are on the safe Wi-Fi signal. Any way around that?
Question, dose the camera connect to the homebase directly or via the network? Means can i hide the homebase somewhere at the house where it’s connected to the network and the camera outside connected to the same network? Or the video feed going directly from the camera to the base without going to the home router? Other question do you know if it’s still not supported with iCloud+? Thanks
The home base after setup does not need to be hardwired to your access point after set up. It can connect over wifi. The means you can place it where you like after the fact. Cameras connect over the homebase not your access points wifi. iColud is not supported as far as I know.
@@Wanderer001_Reviews_Clips so to be clear i have to plug it up to the router via ethernet but than after everything is setup, i can unplug the base from the router and still access cameras and recordings with the app? My router is full so i dont have another port to keep the base plugged in.
@@hybridmods4228 There is an option in the app that you will have to change first. But after that the home base can work over WiFi without taking up a port on your router.
I wish EUFY would get their stuff together because one of their experts told me that the cameras connect to Wifi and from there, they go to the homebase and the hard drive. @@Wanderer001_Reviews_Clips
@@Wanderer001_Reviews_Clips After the first wired setup, does it have to connect the same internet from the router if want to use WiFi? Or another internet connection from another router could be used?
I have a dual band router 2.4 and 5 ghz , i have connected through a wire my home base first ,then i wanted to connect it through the wifi however it says that my wifi supports 5ghz (not true ) i even turned off 5gjz for the purpose of connection with my router and still nothing ! Another time i tried and it says that my eufy app and router may not be on the same wifi settings ? Have you experienced that ? Thx
It sounds like you could have a wifi router that uses the same name for 2.4 and 5ghz. Which could cause that "issue". As for not being on the same network, I have had that happen if I am on my guest network or still on cellular data and not my wifi.
@@Wanderer001_Reviews_Clips Interesting. I did initially hard wire to my router and set up the cameras, then disconnected hard wire and moved my Homebase across the house to the window closest to the camears. Then I looked on my software on my iphone, but did not see an option for wireless. I'm guessing I should have looked for this option while Homebase was still wired to the router?
My friend its me again 😅, all of a sudden the homebase has restarted on its own and nothing appears on the app . Now when i try to setup the system and add the homebase i get this message “unabel to add homebase3” even though I followed all the steps it fails at the last step “ press the SYNC/ALARM button untill it beeps “ and it does but then nothing happens! I even tried using the reset button still nothing happens! Thank you for your support.
That might be a little beyond what I can help. You hit the areas that I would have suggested looking into. At this point it might be time to contact eufy tech support.
Is there one in particular you were looking for. Right now it seems that the cameras that they said would be compatible with the Homebase 3 will not bet getting an update until mid 2023 now.
@@Wanderer001_Reviews_Clips I have the E210, S220 Indoor Cam, Solo IndoorCam C24,, & S230 SoloCam S40. I was under the impression these will be available to connect to Home Base by March
Hello my friend, I just bout the 3c system and i keep receiving notifications from camera because of the TV , how can i stop notifications coming because of TV
Hi Question, does that mean that when I installed the cam into the Homebase 3, I can use this camera to other locations like the homebase is at my home and the camera is at my office, as long as it is connected to the internet?
@@Wanderer001_Reviews_Clips another question, it can use wifi after setting up with using the ethernet cable connectes to the router? And then the cameras can be connected to the homebase within the same local network?
@@Wanderer001_Reviews_Clips Hi its me again, lets say we have 3 rooms with different routers, but the routers are like access points they still have the same default gateway, the cameras can still be connected to the homebase 3?
Hi. Do you know how can I check the signal strength after installing the camera? I want to look for the best placement with a high signal strength but I don't know how to see that option that appeared during the installation of the camera. Thank you
There is a little icon when you click into the settings for the camera next to the charging icon should look like a wifi signal icon. this shows you the strength of the connect. It is not as good as the one during setup but should give you a pretty good idea.
@@Wanderer001_Reviews_Clips Thank you. I saw that one but I thought that I could reach the one during the setting of the camera. Thank you for taking care!
I removed mine from the apo as it lost connection, the camera is a brick now, no beep in the sync button and cannot be connected again, the support from Eufy cannot get more stupid
Hi. remove camera from home base and now cant connect to home base. My camera not doing beep after i press sinc baton. Maybe can help someone? Because eufy support not helping to me. Because i buy camera not from eufy authorized store... thanks.
@@600lorinser Is the home base connected via eithernet? Could also try fulling charging the camera as well. I know I had issues with mine and had to hold it oddly to get it to pair up as seen here: th-cam.com/video/JgMxFxa7FPk/w-d-xo.htmlsi=S43FuxWfMJyrG-fW&t=175.
@@marcellafalzon9431 It could be that it is taxing your wifi connection too much. Depends on how many things you have connected over wifi as well as how good your wifi router is.
What brand/model router are you connecting hb3 to? Also what id the color of the led light at the back where you plug into Ethernet cable? My current router is Tp link a7 archer and hb3 is not able to connect to router via Ethernet cable. Other all devices are able to connect.
I was using the ASUS RT AX88U to connect to the HB3. The color of th light where I connected the HB3 to my Asus was flashing green and amber shwoing data passing.
What supposed you buy something solar but you needs plug the base to the electricity that's the more wrong deal I gonto return my camera because no works with my 5g wifi
The cameas are solar powered the base station needs to be powered some how. If it stays inside it really can't be solar powered. 5g wifi is what your cell phone uses, unless you mean 5ghz. In which case there are not a lot of cameras out there right now that use that spectrum.
@@cocolee8396 You can only use one of the two home bases. Eufy is currtly retoractivly making it so thier older cameras are compatable with the home base 3.
![ไข้ขึ้นเลย! เมื่อแฝดโดนจัดเต็มวัคซีนครบ2เดือน🤒 [cc] แดนแพทตี้ SS2 | EP.54 |](http://i.ytimg.com/vi/z2VHItnyyvY/mqdefault.jpg)
u did a great job : just what we needed, no expensive software nor time consuming editing on ur side, just the essentials thanks !
Thank you for the video. Does the home base have to stay connected via the Ethernet cable to the modem all the time?
After the setup processes the Home base can be set to operate over WiFi, letting you place it a little better then if it had to be connected to Ethernet.
I've seen a video where it's said that when the homebase is connected to WiFi, it won't record 24/7 feeds, just clips (like motion detected event etc.)
is it true ?
I am planning to buy eufy cam 3 4k. I want to install one outside and one inside the house. Will ot work the one inside the house ? Even there is no sunlight direct to the solar panel.
It would work but it would not keep the battery topped off if it does not have access to sun light.
I just received our new home base 3 we currently have a home base 2 with 3 cam2 cameras currently working. Do i have to take them all down and hold them near the new home base 3 and reinstall them again?
You may be able to leave them in place, I just happened to need to move these closer to get them to pair.
Hi i have a old eufywireless doorcam 2k after i changed broadband now my chime cannot sync to the doorbell cam. I want to ask if i buy the homebase 3 that i can connect that to my doorbell cam and then have my echo 8 as a chime
I know this might be making this very simple but when you changed broadband providers did they use the same wifi name and password you had setup before?
@@Wanderer001_Reviews_Clips No all the details of username and password was changed so I removed the doorbell and chime from the eufy app then when I tried to set it up again on the new broadband the doorbell does not syc to the chime anymore
@@Choco_kitty35Did you get a new wifi access point? Might need to try moving it closer to it durning setup. I know I have used a few things like that in the past that needed to almost be right on top of my old setup.
So I have a mesh network which covers the whole house and my outdoor patio. However, when I do the setup, it wants it to connect to the router Wi-Fi. After I do that, I cannot connect my additional cameras to the hub unless they are on the safe Wi-Fi signal. Any way around that?
Lo resolviste ? Tengo el mismo problema …. Ayuda
Question, dose the camera connect to the homebase directly or via the network? Means can i hide the homebase somewhere at the house where it’s connected to the network and the camera outside connected to the same network? Or the video feed going directly from the camera to the base without going to the home router? Other question do you know if it’s still not supported with iCloud+?
Thanks
The home base after setup does not need to be hardwired to your access point after set up. It can connect over wifi. The means you can place it where you like after the fact. Cameras connect over the homebase not your access points wifi. iColud is not supported as far as I know.
@@Wanderer001_Reviews_Clips so to be clear i have to plug it up to the router via ethernet but than after everything is setup, i can unplug the base from the router and still access cameras and recordings with the app? My router is full so i dont have another port to keep the base plugged in.
@@hybridmods4228 There is an option in the app that you will have to change first. But after that the home base can work over WiFi without taking up a port on your router.
I wish EUFY would get their stuff together because one of their experts told me that the cameras connect to Wifi and from there, they go to the homebase and the hard drive.
@@Wanderer001_Reviews_Clips
@@Wanderer001_Reviews_Clips
After the first wired setup, does it have to connect the same internet from the router if want to use WiFi? Or another internet connection from another router could be used?
I have a dual band router 2.4 and 5 ghz , i have connected through a wire my home base first ,then i wanted to connect it through the wifi however it says that my wifi supports 5ghz (not true ) i even turned off 5gjz for the purpose of connection with my router and still nothing ! Another time i tried and it says that my eufy app and router may not be on the same wifi settings ? Have you experienced that ? Thx
It sounds like you could have a wifi router that uses the same name for 2.4 and 5ghz. Which could cause that "issue". As for not being on the same network, I have had that happen if I am on my guest network or still on cellular data and not my wifi.
@@Wanderer001_Reviews_Clips great thank you
Hi, can you connect this to an external monitor as opposed to only being able to view the camera on your phone?
You can not. Eufy does have a web portal but you will need a actual computer to look at it.
How do you then connect Homebase to the router via wireless? I could not find a wireless option on my unit.
You need to set it up via hard-wired first. Then, you will get the option for wifi after you do a firmware update.
@@Wanderer001_Reviews_Clips Interesting. I did initially hard wire to my router and set up the cameras, then disconnected hard wire and moved my Homebase across the house to the window closest to the camears. Then I looked on my software on my iphone, but did not see an option for wireless. I'm guessing I should have looked for this option while Homebase was still wired to the router?
@@gilltim5711 Yes that is correct. It still needs to be wired to select the option to be wireless.
@@Wanderer001_Reviews_Clips Thanks! 😀
Can you plug the homebase to your existing router or does it require a special router box.
Yes you can. You do not need an extra device that it plugs it into.
Thankyou!
Does this device work with Apple HomeKit?
It does not.
My friend its me again 😅, all of a sudden the homebase has restarted on its own and nothing appears on the app . Now when i try to setup the system and add the homebase i get this message “unabel to add homebase3” even though I followed all the steps it fails at the last step “ press the SYNC/ALARM button untill it beeps “ and it does but then nothing happens! I even tried using the reset button still nothing happens!
Thank you for your support.
That might be a little beyond what I can help. You hit the areas that I would have suggested looking into. At this point it might be time to contact eufy tech support.
Hi please can I ask if the home base has a built in fan? Is it noisy?
No fans, just vents. Very silent. The most I hear is the hard drive spinning up in it from time to time.
how many meters can the camera can conect the home base i ean the distace between them
Very dependent on wall type it needs to go through but I have had it as far as 21.81 m when I was testing.
Can you do a video of how to add older eufy cameras to home base 3?
Is there one in particular you were looking for. Right now it seems that the cameras that they said would be compatible with the Homebase 3 will not bet getting an update until mid 2023 now.
@@Wanderer001_Reviews_Clips I have the E210, S220 Indoor Cam, Solo IndoorCam C24,, & S230 SoloCam S40. I was under the impression these will be available to connect to Home Base by March
@@kyoung3482 That was the orignal plan from eufy but seems that things have been pushed back.
Ah maybe this is my issue I have the newest flood.light cams and the 360
Hello my friend, I just bout the 3c system and i keep receiving notifications from camera because of the TV , how can i stop notifications coming because of TV
When you say you get notifications from your tv is that because the camera is pointed at the TV?
yes , the TV is in the living room and the camera detects the faces and motion in the TV and send me notifications
@@mhmdsulami If you set up a detection zone that avoids the area with the tv this will stop it from sending you notifications.
@@Wanderer001_Reviews_Clips thanks a lot it works great now 👍🏼
@@mhmdsulami Good to hear it is working for you now.
Hi Question, does that mean that when I installed the cam into the Homebase 3, I can use this camera to other locations like the homebase is at my home and the camera is at my office, as long as it is connected to the internet?
No, the camera and home base need to be on the same wifi network in order to work.
@@Wanderer001_Reviews_Clips thank you for the clarification
@@Wanderer001_Reviews_Clips another question, it can use wifi after setting up with using the ethernet cable connectes to the router? And then the cameras can be connected to the homebase within the same local network?
@@Khalixer97 Yes that is correct.
@@Wanderer001_Reviews_Clips Hi its me again, lets say we have 3 rooms with different routers, but the routers are like access points they still have the same default gateway, the cameras can still be connected to the homebase 3?
Hi.
Do you know how can I check the signal strength after installing the camera?
I want to look for the best placement with a high signal strength but I don't know how to see that option that appeared during the installation of the camera.
Thank you
There is a little icon when you click into the settings for the camera next to the charging icon should look like a wifi signal icon. this shows you the strength of the connect. It is not as good as the one during setup but should give you a pretty good idea.
@@Wanderer001_Reviews_Clips
Thank you. I saw that one but I thought that I could reach the one during the setting of the camera.
Thank you for taking care!
Is it eligible Apple HomeKit ?
It is not.
Hi
Thanks, can homebase 3 do continuous recording if extra storage is added eg CCTV
Thanks
It can not. Meant to just store clips from cameras attached to it.
I removed mine from the apo as it lost connection, the camera is a brick now, no beep in the sync button and cannot be connected again, the support from Eufy cannot get more stupid
Have you done a hard reset?
Hi. remove camera from home base and now cant connect to home base. My camera not doing beep after i press sinc baton. Maybe can help someone? Because eufy support not helping to me. Because i buy camera not from eufy authorized store... thanks.
You can try powering on and off the home base 3 then try paring the camera after that.
@Wanderer001_Reviews_Clips i try everything what i can... :)
@@600lorinser Is the home base connected via eithernet? Could also try fulling charging the camera as well. I know I had issues with mine and had to hold it oddly to get it to pair up as seen here: th-cam.com/video/JgMxFxa7FPk/w-d-xo.htmlsi=S43FuxWfMJyrG-fW&t=175.
Can homebase unit be connected on wifi rather then cable
After you first set it up you can select to use it over wifi in the app.
@@Wanderer001_Reviews_Clips I have done so but it keeps going and saying cameras off line I even bought deco mesh pods - is it because it’s on wifi
@@marcellafalzon9431 It could be that it is taxing your wifi connection too much. Depends on how many things you have connected over wifi as well as how good your wifi router is.
What brand/model router are you connecting hb3 to? Also what id the color of the led light at the back where you plug into Ethernet cable?
My current router is Tp link a7 archer and hb3 is not able to connect to router via Ethernet cable. Other all devices are able to connect.
I was using the ASUS RT AX88U to connect to the HB3. The color of th light where I connected the HB3 to my Asus was flashing green and amber shwoing data passing.
What supposed you buy something solar but you needs plug the base to the electricity that's the more wrong deal I gonto return my camera because no works with my 5g wifi
The cameas are solar powered the base station needs to be powered some how. If it stays inside it really can't be solar powered. 5g wifi is what your cell phone uses, unless you mean 5ghz. In which case there are not a lot of cameras out there right now that use that spectrum.
So you just buy a hard drive and install it. That's it? Nothing to download?
Nothing extra to download as you already would have the eufy app. The drive would then just need to be formatted then it is good to go.
I csnt my flood lights to pair with the home base....
Only a small set of cameras are compatible with the home base 3. Eufy is slowly making other cameras compatible but it will take time.
I have home base 2 and cam 2 pro can I add home base 3 and the cam 3 to it?
@@cocolee8396 You can only use one of the two home bases. Eufy is currtly retoractivly making it so thier older cameras are compatable with the home base 3.
@@Wanderer001_Reviews_Clips oic pls update us and make a video how to set up thank you very much
@@cocolee8396 How to set up which part?