Pretty cool ring roller. The toll could be scaled up for larger work too. The only suggestion I would make is to put the rollers in double shear to eliminate any deflection. I really like simple tools like that that can be made from project scrap. This is a good tool to teach fabrication skills to a newbie.
Thanks for sharing, but I have a welding machine, drilling as much many people, and an angle grinder. You do have much much more tools. Simple things with the simple tools are much more easy for us.
Hope this one is better than the one I just sent back. The shaft was so loose in the bushing that the drive gear would not stay in place against the cutter wheel. (ugly grinding noises and gear locking up!) Not sure how you tell the quality before you buy online. This did not post where I intended. It should have gone with the sheet metal shear drill attachment. It's still good FYI.
100%. Plus don't drill on short pieces of metal while holding it by hand and putting your fingers down in a pipe and creating a pinch point to act as a powered shear. Was totally cringing.
Он был бы простым, если бы для его изготовления не потребовался токарный станок, это раз. Он нужен если гнуть такие заготовки в больших количествах, это два. А десяток таких колец из полосы, тем более такой толщины на раз два в тисах на трубе с упором.
Muy confiado para perforar en el taladro de árbol, yo me ayudo con la herramienta hombresolo, para evitar un posible accidente. Las manos son lo más que hay que cuidar.
not a good idea to wear gloves around a drill press , a buddy of mine did , that the metal shaving caught his glove and tore his finger right of the bone
An Bohrmaschinen arbeitet man niemals mit Handschuhen schnell sind da ein Finger weg. Tu das nie wieder! ansonsten sehr gutes Video und ein gutes Werkzeug
A break is primarily for sheet metal. Rolls (or roller) are also for sheet metal use unless they are grooved, then they will do rod as well. This tool is neither and is adequately named. Duh!
Aside from the fact that I don't own or have access to a lathe, the cost of bearings and stock metal would be more than I could justify for a tool that I might use once a year. MIGHT. But if you're into making wooden buckets and need bands to bind them, this'll put you right in business.👍
Don't waste watching video every step time killing such as cutting grinding drilling tapping welding all operations slowly make fast edit man Otherwise irritation and skip your videos
Pretty cool ring roller. The toll could be scaled up for larger work too. The only suggestion I would make is to put the rollers in double shear to eliminate any deflection. I really like simple tools like that that can be made from project scrap. This is a good tool to teach fabrication skills to a newbie.
🙏🙏
Посмотрел до конца
И понял что такой девайс мне не нужен .
Но мастеру лайк , было приятно смотреть.
🙏🙏
Ну хоть подшипники варить перестал, это радует.
Gran trabajo amigo saludos desde Uruguay 🇺🇾🇺🇾🇺🇾
🙏🙏🇮🇩
Kolay gelsin ustam elinize emeğinize yüreğinize sağlık değerli bilgiler için çok teşekkür ederiz iyiki varsınız 🇹🇷🤷👍👏
🙏🙏🇮🇩💐
Thanks great work but gloves not allowed on drilling machine
🙏🙏
Very few people have a lathe sitting in their back pocket cool video!!!😂
🙏🙏
Thanks for sharing, but I have a welding machine, drilling as much many people, and an angle grinder. You do have much much more tools. Simple things with the simple tools are much more easy for us.
🙏🙏🙏
The simplest metal bender is a log and a big hammer. But I may be showing my blacksmith bias.
Excelente idea, muchas gracias
🙏🙏💐
I love it. I do wish I had a lathe. What is the heaviest metal this would shape ??
🙏
Bravo 👍👍👍👍👍
🙏🙏
Хороший инструмент для гаража супер 💪👍👍
🙏🙏
Looking to loose some fingers holding items like that when drilling
🙏
Muy bueno 👌😸
🙏
Not all of us are great engineer's. We just love getting down and dirty with metal, do a bit of welding and bit of bending. It's my recreation
🙏
Well tell me is not a simple pleasure when it may not be your day job
This is very good video 😀😃😄
🙏
Hope this one is better than the one I just sent back. The shaft was so loose in the bushing that the drive gear would not stay in place against the cutter wheel. (ugly grinding noises and gear locking up!) Not sure how you tell the quality before you buy online. This did not post where I intended. It should have gone with the sheet metal shear drill attachment. It's still good FYI.
🙏🙏
Very Cool. Nice work
🙏🙏💐
Маладэс ! 👍
Мне такой же сделай.😉😁
🙏
Never wear gloves when working with rotating machinery.
🙏
100%. Plus don't drill on short pieces of metal while holding it by hand and putting your fingers down in a pipe and creating a pinch point to act as a powered shear. Was totally cringing.
Am watching all videos
🙏
Very Nice tool
🙏🙏
Что же Вы метчик не жалеете?
Смазку любую применяйте, хотя бы, воду!
🙏🙏
Он был бы простым, если бы для его изготовления не потребовался токарный станок, это раз. Он нужен если гнуть такие заготовки в больших количествах, это два. А десяток таких колец из полосы, тем более такой толщины на раз два в тисах на трубе с упором.
👍👍🙏
Интересный вы народ. Не надо вам, посмотрели? И молча ушли.
સરસ
🙏
Sos un genio!!!!!
🙏🙏
Охренеть! Затратить столько ресурса и материала,чтобы в результате получить никому ненужную хрень!
🙏
Восток - дело тонкое......😉
И сверло спалить ( 3:30)
Вы за себя говорите. Не надо от моего имени. Я вам доверенность не отписывал.
Genial! aunque ,no para cualquiera...
🙏
Good advice.. Don't use gloves while drilling in metal..Metal debri can pull of a finger !!😮
🙏
Good job
🙏🙏🎉
Beautiful
🙏💐
Muy confiado para perforar en el taladro de árbol, yo me ayudo con la herramienta hombresolo, para evitar un posible accidente. Las manos son lo más que hay que cuidar.
🙏
Ottimo👍
🙏🙏
Ok,if you have alot of rolling, otherwise by a small hand roller save time and energy
🙏
Muy bueno! Gracias!
🙏🙏
not a good idea to wear gloves around a drill press , a buddy of mine did , that the metal shaving caught his glove and tore his finger right of the bone
👍🙏
Agree don't wear gloves
Bonne. Réalisation bravo
🙏
احسنت أداة جميلة جداً
🙏🙏🎉
You tell me that, what can i do when i have not a lathe machin ? 🤨
Bom demais Parabens
🙏🙏
Mantap bos ku
🙏🙏
У меня нет товарного станка, поэтому не смогу.А так очень хороший станок!
🙏
Realy good.
🙏🙏
Where can I purchase the bearings u used thanks in advance
🙏🙏
@@asiawelder so where is it I can purchase these bearings
Muy buena Sencilla y efectiva Muy bien Asia welder
🙏🙏🎉
Lanjut kawan...
Siap 🙏
show ideia muito top
🙏🙏
No doubt if you have a metal turning lathe, that you would also have a metal saw! So much quicker and safer on your project.
🙏
Why wouldn’t you put a couple drops of cutting oil BEFORE you thread those holes ?? Just saying
🙏
è un ottimo congegno ma chi non ha possibilità di un tornio?
👍🙏
What is the name of the music in the background?
🙏
Muantaaaap ...❤
🙏🙏♥️
Talvez sejam poucas pessoas saibam fazer porque não é tão simples quando entre em cena um torno mecânico.
🙏
Merci beaucoup
👍🙏
Зря время потерял напросмотр
🙏
Нам об этом зачем знать?
Устройство из серии "машинки для стрижки тараканов"...
🙏
What's up with these 5 thou cuts on the lathe? And 12 and a half minutes of that song is about 12 minutes too much.
🙏
Iva bn hasta q saco una maquina industrial q la verdad nadie tiene en la casa asi q deje de ver el video😒
🙏
Станок токарный осталось купить...
🙏
Ага...😂😂😂
Сверло заточки требует.
👍🙏🙏
No oil for bits, gloves on near machinery. Are you all trying to piss people off with dull bits or just hurt them?
🙏
Wow, wirklich schön anzusehen deine Handwerkskunst. Gibt es dafür einen zeichnungsplan den Sie bereitstellen würden? Vielen Dank fürs hochladen
🙏
Respekt pdr gjithcka
Уважаемые изготовители и заказчики, как же вы не можете понять? Урны должны быть круглыми!😮😮😮😮😮😮
🙏
Porque no les hace falta....tienes un torno, aparato de soldar y haces estas tonterías ?
🙏
В мире существуют отрезные резцы для токарного станка....
Резцы существуют в магазинах а вот под рукой не оказалось еще они имеют свойство ломаться скалывается напайка вот
🙏
nice slide guitar music
🙏🙏
😊5@@asiawelder
you doing will
we love you.
🙏🙏♥️
Нихрена себе простой😂😂😂. Да делают из подручных средств намного проще....
🙏🙏
Look at this simple tool that I made using a $10.000 machine
🙏🙏
An Bohrmaschinen arbeitet man niemals mit Handschuhen schnell sind da ein Finger weg. Tu das nie wieder! ansonsten sehr gutes Video und ein gutes Werkzeug
👍🙏🙏
Супер👍
🙏🙏
Cool
🙏
Для такой фигни,сварка,дрель,такарный,а результат ,обыкновенный трубогиб; рычаг,два- три болта и одна опора.Не нужно городить огород.
🙏
Too long video
🙏
У корте процессы резки шлифовка сверления и пр. Что возможно
👍🙏
Mit der Ständerbohrmaschine bohren und Werkstück nicht einspannen, echt ? :(
🙏
No. Me convence más es la música q ponen y no explica ni michi
🙏
можно сделать в 100 раз проще !
🙏
Akinek van ennyi gépe, az tudja is. Akinek meg nincs az vesz egyet, mert külömben többe kerülne a leves, mint a hús!😂
👍🙏
un pò di olio quando usi il maschio per filettare ed danche per forare non guasta
👍👍🙏
👍👍👍👍👍
👍👍👍🙏🙏
Semplice strumento.....??
🙏
а ниче что подшипник приварен!!!???
🙏
Простой инструмент это когда смастерил без проблем. А не токарить, сотню подшипников ставить и т.д...
🙏👍
Дешевле будет готовый купить😅
🙏
ما اسم الموسيقا
🙏
Pero no muestran La parte del eje para girarlo con el taladro les falló
🙏
Mejor lo compro echo me sale más barato que ponerme en todo ése trabajo toca tener un taller completo
🙏
Сплошное нарушение техники безопасности😢
🙏🙏
Хорошее приспособление, но можно это ускорить. Зачем показывать от и до. Пожалейте время.
🙏🙏
That is not a metal bending tool! METAL BENDERS ARE CALLED a BREAK.
IT'S called s set of ROLLERS. Duh!
🙏
A break is primarily for sheet metal. Rolls (or roller) are also for sheet metal use unless they are grooved, then they will do rod as well. This tool is neither and is adequately named. Duh!
Aside from the fact that I don't own or have access to a lathe, the cost of bearings and stock metal would be more than I could justify for a tool that I might use once a year. MIGHT. But if you're into making wooden buckets and need bands to bind them, this'll put you right in business.👍
🙏🙏
And again he's making a high-end beautiful tool just use bushings for some grease on and be done make that same tool in 10 minutes
And it won't cost an arm and a leg and make it out of scrap plumbing from the backyard
Thanks sir
생각보다 만들기 너무 어려운데요.. 저 장비들 구해서 놓을곳도 없음.. ㅋㅋㅋ
🙏
Oil !!
🙏
bisogna specifica le misure dei materiali impiegati
🙏🙏
Na realidade isso é um laminador
🙏
Простой..куча подшипников, токарный станок...делов-то.
🙏
😂😂😂проще некуда
а салом смазать метчик?
🙏
Don't waste watching video every step time killing such as cutting grinding drilling tapping welding all operations slowly make fast edit man
Otherwise irritation and skip your videos
👍
прикольно
🙏
Классс
🙏🙏♥️💐