This was really helpful - thankyou. I dropped the lid off the washer filler spout down behind the headlight and I couldn't figure out what the last holding point for the headlight was. Thanks again !!
Thank you very much. Most helpful. (FYI Bought some H7 Osram Nightbreakers but just found that that 2011 FL2 now uses H11 for dipped beam and H7 for main beam .. contrary to most bulb web sites. So, fitted them as replacement main beams and will buy some H11's for dipped. ) Appreciate all the work you put into this presentation. Made it easy to follow.
Thanks Chap!!!! The technicians here across the pond don't like helping out, so your video was excellent to help me remove the ridiculous hood switch sensor without having to remove the front bumper. Keep up the good work and keep making videos, will ya?
Thank you for this video - very useful as before watching your clip and seeing how easy it was I was balking at the task - I had a few issues getting the retaining rod back on as I was worried I would snap the plastic but got there in the end (applied some Fairy Liquid - other products are available) - cheers.
I have a bulb gone, was a little surprise did have to take the unit out to change a bulb, but then I remember removing wheel arch trims on a Renault, and the bumper for my BMW fog lights, so, a leather man, 2 clips and a lever isn't too much to complain about!
Thanks for this useful. I found the round connector turns a little - is this normal and it sits at a slight angle? I also found the little grey clips that secure the H11 headlight bulb power are brittle and one snapped away. Can the connector wire be replaced or should I not worry? (2011 H11 Projector)
Don't know how it's possible, but did this a while back and as a result the vehicle inspection officer said the headlights are pointing in every direction but the direction they should be pointing. IMO not noticable, but apparently is. Thanks for the video anyways, I thought everything went just as it should, but apparently not. Lesson learned: Don't listen to the vehicle inspection officer.
01:38 hi my sport has the same electrical connector. i can not get it back to the headlight after my work done. any suggestions on how to reconnect them? thanks every one
One reason we dont sell them is that there are so many types - LHD / RHD / Early / Late / HID etc ect. if you give me your chassis number i can get you a PN and price
The clip you are pointing to does not marry up with the 'plunger'. I just did this on my freely 2. In addition, you are supposed to pull up the 'plunger' in order to release the whole unit from the housing. Yours must be as shit as mine as I didn't need to do that either.
Hi, do you have some kind of advice for me, to clean the inner surface of the plastic glass? There's some dust in there. It seems you can remove the whole of it and wash it, but it's not..
![[Full] 4 ต่อ 4 Celebrity EP.920 | 3 พ.ย. 67 | one31](http://i.ytimg.com/vi/KwiW2M_kAg4/mqdefault.jpg)
This was really helpful - thankyou. I dropped the lid off the washer filler spout down behind the headlight and I couldn't figure out what the last holding point for the headlight was. Thanks again !!
Thank you very much. Most helpful. (FYI Bought some H7 Osram Nightbreakers but just found that that 2011 FL2 now uses H11 for dipped beam and H7 for main beam .. contrary to most bulb web sites. So, fitted them as replacement main beams and will buy some H11's for dipped. ) Appreciate all the work you put into this presentation. Made it easy to follow.
Mines the same so it seems that LR changed the spec from 2011
Thanks Chap!!!! The technicians here across the pond don't like helping out, so your video was excellent to help me remove the ridiculous hood switch sensor without having to remove the front bumper. Keep up the good work and keep making videos, will ya?
Brilliant so simple no taking bumper/ front end off!!
Outstanding instructions. Now have working dipped headlamps again.
Thanks, it worked for me (Australian Freelander 2). Saved me time, money, and probably saved me from breaking things too!
Thanks, great video. Saved me a trip to a mechanic for a simple job
Thank you for this video - very useful as before watching your clip and seeing how easy it was I was balking at the task - I had a few issues getting the retaining rod back on as I was worried I would snap the plastic but got there in the end (applied some Fairy Liquid - other products are available) - cheers.
I think it's very generous and helpful of you to make these videos for us. Thanks very much!
I have a bulb gone, was a little surprise did have to take the unit out to change a bulb, but then I remember removing wheel arch trims on a Renault, and the bumper for my BMW fog lights, so, a leather man, 2 clips and a lever isn't too much to complain about!
great video - enabled easy removal and reinstatement after bulb replacement
Thank you for your video. I managed to change out the light easily.
Thanks for this useful. I found the round connector turns a little - is this normal and it sits at a slight angle? I also found the little grey clips that secure the H11 headlight bulb power are brittle and one snapped away. Can the connector wire be replaced or should I not worry? (2011 H11 Projector)
From memory i think the connector is at a slight angle
I have looked at the parts catalogue and there are not many spares parts offered by Land Rover
Well that saved me asking Halfords to do it at £8 a pop! Great video and thanks!
Hi - the irony is Halfords do a series of radio adverts taking the mick out of youtube DIY videos !
Hi
,thanks for the great videos! and can you tell me is it possible to upgrade the 2008 lights to the 2012 led version headlights?
thats also what i whould like to know :)
Still waiting for an answer about this. lol
Superb video…thank you!
thanks
Don't know how it's possible, but did this a while back and as a result the vehicle inspection officer said the headlights are pointing in every direction but the direction they should be pointing. IMO not noticable, but apparently is.
Thanks for the video anyways, I thought everything went just as it should, but apparently not. Lesson learned: Don't listen to the vehicle inspection officer.
Hi brill video very helpful.
Could you tell me is it a sealed headlight.
Thanks matty
Hi
The headlight is not sealed - you can change the bulbs - i think i did another video how to do that but cant remember.
01:38 hi my sport has the same electrical connector. i can not get it back to the headlight after my work done. any suggestions on how to reconnect them? thanks every one
thank you for all the videos ! very helpful!!!
Thanks... you have a treat today as there is a new Freelander 2 headlight video coming !
@@L663 may i ask -- will you make a video how to install rear cam and multimedia on Freelander 2 ?
excuse me but whats the name of the tool so i can unscrew bolt on the top of the headlight ?
Yeah the Freelander 1 has a bolt under it what a nightmare glad they changed it
Hi, many thanks very clear and very helpful
would these headlights fit in a 2001 Freelander, or are they totally different?
Well done this was really helpful, thank you.
I can't find a website that sells new headlights I need the drivers side. I looked on ebay and they are all used.
One reason we dont sell them is that there are so many types - LHD / RHD / Early / Late / HID etc ect. if you give me your chassis number i can get you a PN and price
Great Video
A great help, cheers!
Como remover a lanterna do Freelander 2? Vc pode me ajudar ?
The clip you are pointing to does not marry up with the 'plunger'. I just did this on my freely 2. In addition, you are supposed to pull up the 'plunger' in order to release the whole unit from the housing. Yours must be as shit as mine as I didn't need to do that either.
very helpful thank you very much
can these lights fit a landrover freelander 1
Hi, do you have some kind of advice for me, to clean the inner surface of the plastic glass? There's some dust in there. It seems you can remove the whole of it and wash it, but it's not..
It worked for me. Many thanks. isn't the web a wonderful thing.. Haha landrover dealers!!!!.
Thanks to uploader
What about a 2001?
Totally different shape so cant fit the early model
Thank You :o)
👏🏼👏🏼
show thanks!