Great video - did the trick for me on the rear door trim. Just have to remember to leave the inside rubber seal dangling untill the trim is in place and then hold glass and squeeze the rubber down between window and new trim. Thanks Vlad!
I had a bent pillar and top moulding in the rear window of my 2010 VW Jetta caused by an accident with the previous owner. The bent pillar allowed air to whistle through at high speeds. While it has performed as a good commuter car, it really wasn't worth it to put a lot of money into it. With the help of your video, I was able to remove the pillar and trim and found that the steel flange holding the trim at the top of the door was bent. This caused the trim piece to bend downwards and create the open hole. All I needed to do was straighten out the top flange with a few taps of a hammer, then reshape the pillar and put everything back together again following your instructions. It cost me nothing! I wouldn't have attempted it had I not seen your video! You have saved me time and money! Thank you, Vlad!
Merci pour ta vidéo grâce à j'ai pu faire le nécessaire pour les plaquettes de frein de ma voiture et éviter de sortir les sous sous 😅. Si jamais tu as d'autres vidéo ! Je prends 😊
I was unable to get the side wheather stripping back in and had to cut the lower portion off to get the window closed. Now I need to take it to a shop and have them replace the seal.
On my mkv Jetta had to remove the inside front door panel and the window inside sweep moulding. I have a picture but don't know how to share it on here?
Mk5 Jetta is similar, rear door panel is easy, but front panel is a bear to get the rubber back in there. Have to take the inside door panel off. Is there a easier way?
Leave the bottom trim off and insert the rubber on an angle to miss the window regulator mechanism below. Don’t be fooled thinking the window up/down will help. Or, using any type of lubricant.
Great video - did the trick for me on the rear door trim. Just have to remember to leave the inside rubber seal dangling untill the trim is in place and then hold glass and squeeze the rubber down between window and new trim. Thanks Vlad!
You welcome Robin! Appreciate it! ^_^
I had a bent pillar and top moulding in the rear window of my 2010 VW Jetta caused by an accident with the previous owner. The bent pillar allowed air to whistle through at high speeds. While it has performed as a good commuter car, it really wasn't worth it to put a lot of money into it. With the help of your video, I was able to remove the pillar and trim and found that the steel flange holding the trim at the top of the door was bent. This caused the trim piece to bend downwards and create the open hole. All I needed to do was straighten out the top flange with a few taps of a hammer, then reshape the pillar and put everything back together again following your instructions. It cost me nothing! I wouldn't have attempted it had I not seen your video! You have saved me time and money! Thank you, Vlad!
used similar tactics for 2004 Beetle, spot on 🤙
Merci pour ta vidéo grâce à j'ai pu faire le nécessaire pour les plaquettes de frein de ma voiture et éviter de sortir les sous sous 😅.
Si jamais tu as d'autres vidéo ! Je prends 😊
Haven't seen a detailed video on this topic so I decide to make my own one! Hope it will be helpful!
Have you got one putting it back?
3 years on and it’s helped me immensely👌😎
Excellent, great video demonstration.
Great video! sliding the glass channel rubber back is a bit of a fiddle, when you come to put everything back!
saved me so much time ! i thought they where stuck on !
As clear as it gets - thanks for posting!
Thanks for uploading! I've been looking for this everywhere! 🙂
Great video. Thanks for taking the time to show this.
Do you have a video of you putting it back together again?
Muchísimas gracias tu video me sirvió un montón.
I was unable to get the side wheather stripping back in and had to cut the lower portion off to get the window closed. Now I need to take it to a shop and have them replace the seal.
You Fkin legend thank you.
You welcome dude! )))
Thanks 👍
Off to but some new trim to replace rusty existing. Ta very much for methodology
man you saved me some money :)
Can we have a video on how to put a new one in after removing the old one please? Anyone know where to buy a replacement? Cheers!
On my mkv Jetta had to remove the inside front door panel and the window inside sweep moulding. I have a picture but don't know how to share it on here?
Thank you soooo much
You made my day! thanks :)
You welcome :)
now how you put it back lol
Thanks. Is it the same on the MK5 3 door?
Mk5 Jetta is similar, rear door panel is easy, but front panel is a bear to get the rubber back in there. Have to take the inside door panel off. Is there a easier way?
Any idea where I can find this piece for a Tiguan 5N from 2015?
Thanks, but I can't get the rubber bands back in... Now what?
Leave the bottom trim off and insert the rubber on an angle to miss the window regulator mechanism below. Don’t be fooled thinking the window up/down will help. Or, using any type of lubricant.
Just try to guide them with a thin metal stick (the way I have done it).
How in the heck were the screws that easy for you?! I stripped 2 then gave up for the day
Did you try WD-40?
Jessica H I think I might have to use it once u put everything together
can someone please tell me how to build the seal back ? i can't haha
Same for 2007 Vw Jetta????
Where i can buy that piece??
multam
Cu placere :)
Au ceva cod pe ele :D sau stii codul lor?
Thanks!