I bought a Rigger boat constructor, collected everything, the first experience. It does not drive well, does not develop speed, how to properly adjust the angle of the propeller? Thank you.
Nice one😊👍..I think you will get a real surprise how quick this will be,I've just tested my 3652 model rigger and really quick but with no turn fin the steering was insecure so I have a right turn fin ,will you add one? at the very back
I did run a turnfin.. I just ran mine today for the first time. I didn't like the way it ran with the fin I may take it off and use toe in/out for the ride adjustment. She was bouncing on the right sponson so i definitely need to fine tune or do away with fin all together. How did yours turn w/o fin?
@@IRONCLADRC Thanks for that..I added a turn fin as it was unstable steering would go off to the left real easy but at full power seemed great..I think try a fin on both sides 2 is meant to straighten it but I don't have 2 fins
@@IRONCLADRC I will put a vid up a bit later showing how it zipped to the left..Yes maybe you could benefit from toe in toe out but I'm asking others about fitting turn fin on right spontoon and they say yes
you need the turn fin it must be a known type and youll need a digital spirit level to set it .25 of a degree at a time and you need to back off your turn limits toe in about 2 mm on the LH sponson and the fin goes with it .
I've been using a shim between the turnfin and its mount, to try and dial the fin in it's helped a small amount.. Paul are you using 2 turn fins or just 1 on your rigger?
Hi. I have a little outrigger boat like you, i have no turn fins on it and the boat will not turn at any side when more than half throttle, i always had to stop an turn the boat slowly, once i tryed a turn fin on the left side, but that doesent worked, when i pushed the throttle the boat turned to one side 90 degrees to often? Do you have any idea or tip for me?
Normally the turn fin is mounted on the right side (starboard) the back of the turn fin should be inline with the center of Gravity. Try a curved turn fin it hooks better in a turn.
Sorry i mean the turn fin is on the right side and yes it is curved, but i did not check the cg. In this configuration the boat was not able to go straight forward, suddently id did a turn, now i am driving it without any fin but i can not turn like your boats.
Outside is best I don't have a problem with reception with it inside. I suggest using a submerged drive for this boat not a surface Drive line like you see in this video.
Hallo also i have a boat that i must made Till i don´t have any place to can try him Or you do it and they take your boat when they see you with a boat greetings
Well I for one know how you feel, when building airplanes ✈ they will say oh yeah man no problems... I built it in 30 minutes and I spend 2 hours on my servos 😃 I thank you for being honest! 🤩BB
Can’t wait to see it on the water!!
Awesome build bro. Very cool. Almost there.
Papawie Official } Full support you brother VERRY NICE boat
I bought a Rigger boat constructor, collected everything, the first experience. It does not drive well, does not develop speed, how to properly adjust the angle of the propeller? Thank you.
So the shark esc work well i got one never did anything with it
It did okay but the waterproofing on the speed control has a little to be desired.
Nice one😊👍..I think you will get a real surprise how quick this will be,I've just tested my 3652 model rigger and really quick but with no turn fin the steering was insecure so I have a right turn fin ,will you add one? at the very back
I did run a turnfin.. I just ran mine today for the first time. I didn't like the way it ran with the fin I may take it off and use toe in/out for the ride adjustment. She was bouncing on the right sponson so i definitely need to fine tune or do away with fin all together. How did yours turn w/o fin?
@@IRONCLADRC Thanks for that..I added a turn fin as it was unstable steering would go off to the left real easy but at full power seemed great..I think try a fin on both sides 2 is meant to straighten it but I don't have 2 fins
@@IRONCLADRC I will put a vid up a bit later showing how it zipped to the left..Yes maybe you could benefit from toe in toe out but I'm asking others about fitting turn fin on right spontoon and they say yes
you need the turn fin it must be a known type and youll need a digital spirit level to set it .25 of a degree at a time and you need to back off your turn limits toe in about 2 mm on the LH sponson and the fin goes with it .
I've been using a shim between the turnfin and its mount, to try and dial the fin in it's helped a small amount.. Paul are you using 2 turn fins or just 1 on your rigger?
Love mini riggers, small fast and fun. Don't forget to pack the servo with waterproof grease.
I used corrosionX for servo
@@IRONCLADRC Ok if it's grease but the liquid wears off over time. Packing with dielectric watwrproof grease is best. 😊
Nice thanks for the advice my dielectric grease grew legs and walked off. 😆
@@IRONCLADRC That will never last as long as grease or protect water intrusion. 😉
Did you not notice there is a grub a srew on top of rudder to change positions????
Yes sir lol after the fact
Only found out myself mate 🤣🤣🤙🤙
Question if I may rigger prop shaft angle any advice thanks
I'd run it out the bottom of the boat. Run a submerged drive like in this video link th-cam.com/video/zbrH-WIRlpw/w-d-xo.html
Thanks for vid link ya sent , I'm useing soiled prop shaft not flex but will use ya advice thanks mate
Hello, a link for the kit? Thank you very much for your kindly reply
www.ebay.com/itm/275684899891?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=rLHSfwXWQHy&sssrc=4429486&ssuid=yQkZS9FcQay&var=&widget_ver=artemis&media=COPY
Hi. I have a little outrigger boat like you, i have no turn fins on it and the boat will not turn at any side when more than half throttle, i always had to stop an turn the boat slowly, once i tryed a turn fin on the left side, but that doesent worked, when i pushed the throttle the boat turned to one side 90 degrees to often?
Do you have any idea or tip for me?
Normally the turn fin is mounted on the right side (starboard) the back of the turn fin should be inline with the center of Gravity. Try a curved turn fin it hooks better in a turn.
Sorry i mean the turn fin is on the right side and yes it is curved, but i did not check the cg.
In this configuration the boat was not able to go straight forward, suddently id did a turn, now i am driving it without any fin but i can not turn like your boats.
I need to build one of these look to fum
You should sell them as a kit with motor every rtr just add your own remote receiver
Does the receiver antenna just sit inside if the boat, or does it need to mounted to the outside to receive signal ?
Outside is best I don't have a problem with reception with it inside. I suggest using a submerged drive for this boat not a surface Drive line like you see in this video.
@@IRONCLADRC ....you mean tube thru bottom floor of boat ? What motor did you run on 3S ?
Look on top next to intake, grass inlet
hey iron! How long did it take you start to finsh?
Can you teach me how to calibration ztw shark
Hallo also i have a boat that i must made
Till i don´t have any place to can try him
Or you do it and they take your boat when they see you with a boat greetings
? What's the question I didn't understand?
Esc ???
What stick you put in that boat bro?
Venom fly 3s 2200mah 30c pack
Bro what size rudder for your boat plz tel me,???
75mm top of the rudder to the bottom
Cho tôi xin liên kết mua chiếc rigger đó❤
www.ebay.com/itm/275684899891?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=rLHSfwXWQHy&sssrc=4429486&ssuid=yQkZS9FcQay&var=&widget_ver=artemis&media=COPY
Why not bend your steering server rod L and then upside down L? Use slightly thicker wire to avoid flex ;)
Well I for one know how you feel, when building airplanes ✈ they will say oh yeah man no problems... I built it in 30 minutes and I spend 2 hours on my servos 😃 I thank you for being honest! 🤩BB
Waiting for water test bro
I'm finishing her up as we speak should have the video out in a couple days
Brass