How to Replace Driver Side Axle 2008-16 Chrysler Town & Country
ฝัง
- เผยแพร่เมื่อ 15 ม.ค. 2020
- Buy Now!
New CV Axle Shaft from 1AAuto.com 1aau.to/ia/1AACV00314
A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications. This video shows you how to install a driver side axle in your 2008-16 Chrysler Town & Country.
• Check here for more videos on the 2008-16 Chrysler Town & Country • Chrysler Town & Countr...
This process should be similar on the following vehicles:
2008 Chrysler Town & Country
2009 Chrysler Town & Country
2010 Chrysler Town & Country
2011 Chrysler Town & Country
2012 Chrysler Town & Country
2013 Chrysler Town & Country
2014 Chrysler Town & Country
2015 Chrysler Town & Country
2016 Chrysler Town & Country
Tools you will need:
• Pry Bar 1aau.to/oa/1AXAA00020
• 21mm wrench
• 10mm Socket 1aau.to/oa/1AXAA00017
• 18mm Socket 1aau.to/oa/1AXAA00043
• 19mm Socket 1aau.to/oa/1AXAA00043
• 21mm Socket 1aau.to/oa/1AXAA00043
• 32mm Socket 1aau.to/oa/1AAST00003
• 3/8 Inch Air Impact Gun
• Ratchet 1aau.to/oa/1AXAA00016
• Torque Wrench 1aau.to/oa/1AXAA00044
• Bungee Cord
• Cloth Rags 1aau.to/oa/1AXSS00035
• Rust Penetrant
• Center Punch 1aau.to/oa/1AXAA00055
• Drain Pan 1aau.to/oa/1AXAA00320
• Hammer 1aau.to/oa/1AXAA00091
• Rubber Mallet 1aau.to/oa/1AXAA00413
Subscribe: / @trq
Check out our playlist:
Chrysler Town & Country 2008-16 5th Gen: • Chrysler Town & Countr...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - ยานยนต์และพาหนะ
![บุษบา - มอส รัศมี [COVER VERSION]](http://i.ytimg.com/vi/_n0yENSl8d8/mqdefault.jpg)
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
I love how direct and thorough this guy is! Excellent! That is how you make instructional videos! No life story, no big introduction, no fluff, all meat and potatoes!
Good instructions.
Reminder:
Before installing the new cv assembly, remember remove the old spacer on the outer shaft and install onto the new shaft
I just replaced the driver's cv axel in our 08 Grand Caravan and it was easy as 1,2, 4. If you follow the instructions in this video it will work out perfectly. My advice is to soak the nuts and bolts with penetrant the night before. That made it much easier to remove. Also, be careful not to bend the brake rotor splash guard like I did and have to bend it back. Also clean all mating surfaces well and apply anti-sieze or lubricant as needed.
Wow, you should teach a class. Extremely informative as well as efficient.
At 1:47 you pulled the axle spacer off of the old CV shaft, but you did not replace it on the new CV shaft. This is an important part of you don't want a small "knock" in the front end. I learned the hard way not knowing one goes there, because the person who changed it last also left it out. Knock ensued...
Thank you so much, I've used several of your videos, and no one makes it easier!
Great video, went by you instructions and it went on no trouble at all. Thanks for providing the video!!!!!!!
Robert Ewing Thank for watching!
Great vid. I see you removed the sway bar, but forgot to mention anything about it
I just found the hard way you have to remove the upper part of the sway bar, otherwise the old axle will never come out,
Hi,
When putting the new Axle in the hub, I didn't see the thin metal washer that installs between the hub and Axle, does the washer need to be there? I forgot to install mine. Your help is appreciated.
Great video!! Right to the point, very efficient! Thank you so much for helping the average joe!!!
Great video. completed mine today. Saved me a lot of money thanks.
Great video as always, thanks for putting your excellent content on TH-cam for us too learn from 😁
Excellent video! I was having trouble seating the drive shaft in the transaxle-thought I had to twist and push until it went all the way in. Didn’t realize you could “bonk”?it with a rubber hammer! Thanks for the help! PS Since fluid usually leaks out when you pull the drive shaft, why not change your transaxle fluid when you change a drive shaft? My first tranny lasted 200k miles with fluid change every 60k
Awesome video, you make it look so easy but I am not gonna try doing it myself. Will take my 2016 to a mechanic.
+GT Dude Thanks for watching our video! 1aau.to/m/Shop-TRQ
Awesome. Nice and easy to understand. Let's hope I am able to do as easily as he doing it
Wish my 2 Front Axle Replacement was going as smooth as this! Got both Axles coming today from 1A Auto.Mine is a 2008 Dodge Caravan,& is a little diff from this Video.First off,it has OVER 400,000 Miles on it! So the Bolts are Practically GROWN to the VEHICLE!.The Driver Side Axle Busted at Sleeve near wheel,Bearings Fell OUT! Finally got it all oose & Axle most was out.(Waiting for NEW ONE before proceeding).But the tie rod will NOT BUDGE! Tried method here,Penetrate Beating down with Block wood on top,etc.Growed together,siezed up!
Doing my 2013 caravan today. Going to go by your video here. The only thing I noticed is that in other videos, transmission fluid leaks out when you pull out the axles, none came out when you pulled the act salute. I’m assuming it’s because this transaxle was low on fluid? I’m hoping I don’t need to catch bucket.
Great video!
Nice job 👍
GREAT VID!!!
Excelente vídeo 👍🏆👑
Awesome video well done.
+scott hester Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ
Excellent video. When I installed a new axle, the inner boot got squeezed when tighten the nut on the hub. Could you please advice me how to fix that? Is it ok to leave it like that?
Any recommendations for a grinding noise coming from transmission when I accelerate hard
When reinstalling the cv axle, when you're bringing it through the back of the knuckle into the bearing, do the male splines of the axle come out flush with the front of the bearing?? I've replaced my cv axle joint soon to be five times this year alone. I've replaced the struts, control arm, bushings, ball joint, outer tie rod, sway bar bushings, end link, wheel hub & bearing, knuckle and now all the motor mounts!!! What is left?? I also dropped the trans pan (no shavings or fragments, magnet was clean) changed the fluid and the filter. I am still getting the clicking noise in reverse and sometimes when turning the wheel when in drive. ANY insight would be GREATLY APPRECIATED!!
It's all good if you are about to attempt this. He kinda leaves out how to get the two bolts back in under tension. Ya just gotta improvise I guess
What are the exact names for these parts because stores where im from dont seem to know anything about car parts. My car is leaking transmission fluid from the axle seal I believe
Do you have any recommendations for an axle that is totally stuck in the hub?
Is there an axle seal on the passenger side as well? I've watched both your videos on either side and you do not mention anything about an axle seal on the passenger side.
Hello, can you tell, if this operation is the same as in Pacifica 2016-2020?
Wow i always thought the axel was the the main piece avross the botton for both wheels
I had about half a quarter of transmission fluid come out when replacing axle. Was it over filled or do I need to add fluid.
I also had about 1/2 quart or so leak out, I just checked the fluid with engine running and in neutral and added more.
T happens if ace doesn't go in?
Does anyone know if this would be similar to a 2013 Chrysler 300?
So easy even my 12 year old can do it even when I dont have a 12 year old son.
Anyone else notice that at 3:40 in the video the strut was either replaced or painted shiny black within that 1 second time frame? lol. Thanks for the video. I may undertake replacing my leaking shaft seal, the only bummer after saving 100's in labor to install a $4 seal, I have to get a re-alignment?
Yes, very cool! Notice the printing on the tire is backwards, and the nuts appear to be left hand threads. :)
All good unless the axle is beyond seized to the mid axle
Replacing transmission and this is the only thing stopping me lol
2009 Dodge Grand Caravan CV axle is recessed into the transmission. You can't jusr pry it out. Do an instructional video on it.
What about the old washer that you did not reinstall. Dont i need that
Would this be the same on a grand caravan?
+Zach Hill This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ
What! No anti seize?
the torque should be 65 + 90 degree turn, i am sure u just forgot about it because i can tell u are good.
+zaydoon obaidat Thanks for the feedback! 1aau.to/m/Shop-TRQ
You do realize that you did not have to pull the bolts from the strut. It would have saved you an alignment. Time and money. What were you thinking?
Good jop
Mine has no place to place the pry bar or will come out and I'm pulling hard on it and wedging stuff anywhere to take it out and it won't. Love my stupid ass luck
2010 Volkswagen Routon, same process?
How come nobody shows the right side
Id like to see that too. It's a little different, the CV axle doesn't go directly into the transmission.
Pretty sure he shows the right side as well… at least I think it was him I saw it from.
You cant impact a fastener and then use a tq wrench. That negates the tq wrench.
No need to remove ball joint,beginner job
Love how you snuck a new strut in there and didn’t say anything LOL
I’m guessing that was from his strut replacing video. A lot of the footage was the same, but he replaced the strut. Both videos were good.
Great video, went by you instructions and it went on no trouble at all. Thanks for providing the video!!!!!!!