NP231 Rebuild DIY Part 2 TJ LS Swap

Get a NP231 Rebuild kit here amzn.to/2WFpI2h
In Canada get a NP231 Rebuild kit here amzn.to/2JYE0Fc
this is part 2 of the very Detailed NP231 rebuild that i'm doing for my LS Swap Project. Rebuilding the transfer case for your jeep is actually a easy project if you have some basic mechanical skills.

[@ddesilva61]

Informative...however something tells me there is a torque spec for the yolk nuts...

[@TestDontguess]

There is a torque spec for every fastener, feel free to use them as you wish

[@francisbrackney2061]

Front yolk is 125ftlbs, I'm not sure about the rear one for a SYE, it would best to check with a company that makes SYE kits.

[@TheRl30]

what parts did you end up using from the 231C?

[@WTF007WTF007]

Hi, want to ask how do I know the chain is not good anymore? Thank you

[@mariodesmo]

Nice video. Reminded me of when I installed a SYE on my t-case years ago.
Yea, that oil pump in the t-case was as bitch to get in just right, as I remember.
Looking forward to the rest of the swap videos!

[@colewebb4643]

HI BSK garage I injoyed the video 👍👍👍 on you're last video I told you I had mechanic question that I would text on you're next video this one ok I have 94 Ford 150 302 5.0 litter and the engine light is not on so no trouble code I've all ready did a full tune up new fuel and air filter and replaced all four relays it had bad fuel pump relay etc now just before this work it started to have problem ok here's what happening it will crank over fine warm or cold it won't start but if I put some gas in the intake it starts right up runs great will drive fine it just won't start on it's own with out putting a little gas in the intake and yes I put gas in the back gas tank no difference front or back gas tank it still does the same thing do you a have any ideals what caused this to start happening it use to start fine does any body out there have any ideals on what I can check ??? well thank you good night ⛺ C😎😎L

[@TestDontguess]

It’s a sign that it’s time to take it to the crusher

[@colewebb4643]

@@TestDontguess hi the crushers noooo LOL ah you mean you have no ideal LOL 😂😂😂😆 yah I thought of taking to a wrecking yard I played 300 hundred dollars for it and drive it for four year's with out any trouble till about a couple of months ago it still runs great it's in good shape in and out still nice but I do have three other car's so well thank you any ways and you have good night 🌇🌆⛼🌃 guy i'm looking forward to you're next video 👍👍👍 C😎😎L

[@slant6guy]

No more 7-main-bearing AMC 4.0L? Good motor! That new LS v8 ought to make things "somewhat" exciting!
Good video sir as I'm gonna do a SYE here on the 2003 TJ...lots here to see and learn about=thumbs up.
May as well to a TeraFlex 2WD low + 6 gear planetary unit in the NP231J as I wanna be done with it & done right.
Thanx for having this vid here, Jerry. -G'

[@CaudillPat]

I know this is a little older but I have a question. I am using your vid as a play by play for the rebuild of my NP231. My question, the gears that slide onto the rear output shaft. There are two sets of needle bearings and a synchro ring. Do you replace those?

[@roncameron7461]

Thanks so much for your knowledge and video's... also thanks for not swearing so much! It sure makes it easier to watch your videos with my family 🙂

[@joshuadeanb]

Jerry, I didn’t do a SYE-just a regular rebuild. Should there be any forwards to backwards play in the shaft once it is completed?

[@francisbrackney2061]

Great video, thank you. Although personally I think I would have replaced those pads on the front shift fork.
What kind of blind hole bearing puller set is that that you are using? That one looks like it works excellent!.

[@your2nd]

What is the part number for the front output shaft using the 1 1/4" chain and a yoke.

[@fishsticksmlg]

If you buy a small pick kit from HF you can easily seat that pipe if it wants to come loose again when assembling, its the biggest pita when rebuilding it.
Great series man, been awhile since I last watched your chanel. Nice to see you still goin!

[@dirksampson8535]

At 12 minutes i just noticed the biggest snap ring on the bench...

[@roberthayes5037]

Absolutely fantastic, very detailed! Thanks 👍👍

[@lowbornfabrication]

Great Videos!! Wealth of information easily understood and your “common sense” tips are on point!!

[@jordanodom4439]

Where did you get the blind hole puller

[@TestDontguess]

Should be a link in the description

[@leonlathrom4323]

I put gear oil in mine how bad did I mess up

[@titaniumman_22]

Awesome, thanks BSK!

[@roryfruhling9100]

You do good work

[@danhambrick6331]

Thanks Jerry,I feel like I can do that on mine now...

[@TestDontguess]

Yes you certainly will be able too