5vdc Relay Module Connection and Working | single relay module connection | 5v relay connection

In this video....
I hope I have explained the 5vdc Relay modules connection and working...
To see more videos related to industrial electrical circuits So visit my channel and subscribe..
1 relay module connection
2 5vdc relay connection
3 single relay module connection
4 single relay module working
,,
My Other Videos links..
..
BEST TOOL for Electrical work/MULTI FUNCTIONAL TOOL for Wire Stripping & Crimping.
• Wire Cutter , Wire Str...
..
How to Convert HP to KW & KW to HP/Short method of conversion..
• How to Convert HP to K...
..
What is Smoke/GAS Sensor and How it works???
• What is Smoke/GAS Sens...
..
..
Temperature controller /PID controller with SSR and PT100 or thermocouple connection and working
• Temperature Controller...
..
Relay Holding Circuit ...
• VOLT METER USE IN CIRC...
..
Twin Timer or Double Timer Connection & Working
• Twin Timer connection/...
..
8 Pin Timer Connection and working.How to 220vac analog timer wiring.
• 8 Pin Timer Connection...
..
DOL Starter Hold Without Auxiliary point.How To Make A Circuit.
• DOL Starter Hold Witho...
..
#5vdcrelaymoduleconnection #relayconnection #module
#5vdrelaymoduleworking
#relayconnection
#relay
#5vdc8relaymodule
#onlineelectricwork #urdu #hindi #english
.
Thanks for watching....
16/09/2022

[@usamanawaz6101]

Nice Work

[@prateeksaxena3297]

Hi, i am using this relay in one of my project but its nor working upside down.

[@orph4nsx]

Do you have an example for a module for small sensors with 5v?
This module is really big

[@Vignesh-om5dh]

Thanks

[@arshadali4343]

good work

[@onlineelectricwork]

thanks

[@farooqprince4616]

Good

[@juanriofrio6872]

Hello, glad to see your video.... If I may, I would like to ask a question: you provide negative power to the pin IN. I always thought that a positive connection usually is applied to that pin, (I prefer to use the concept, better said the fact the current flow from negative to positive) I have been trying to use a radar little board called HLK-LD2420c, but without any luck. Your video call my attention cause the "output pin" in the radar board I assumed that is a positive pin, but no matter what I did I couldn't make it work. I want to control a light bulb and I am using a 5v relay board as the one you are using. Now that I see your video make me think I am doing something wrong here. Will be too much to ask if could explain is it always has to be a negative connection to the IN pin? Thank you before hand for any thoughts that could explain what am I doing wrong. Good day

[@onlineelectricwork]

at the IN pin we will connect only GND because the relay is getting positive supply internally so if we give it negative then the relay will turn on..
thanks for watching..

[@juanriofrio6872]

@@onlineelectricwork hello, thanks for your reply. I'm wondering how I can accomplish this, sending a negative signal to to IN pin on the relay board. Usually here in the USA when the talk about output the referred to a positive signal (the accept that current flow from positive to negative) . If the radar board is sending a positive signal, that will answer the problems I'm having with it. Could you recommend a way to accomplish this. The radar board it supposed to turn a light when it detect movement . How I can inject a negative signal and at the same time control the ligh? Terrible sorry for my inexperienced knowledge. Hope you can help.... Thank you

[@anitakhandelwal8594]

​@@juanriofrio6872 0:33

[@robertambalong8560]

See specifications of the Songle Relay module used in the circuit here:
* 10 A Relay
* Active Low (Pull to GND)
The relay is active when the control signal is pulled low. If control is left to float or at Vcc voltage, the relay is inactive.

[@gogreen929]

Supper

[@miadikim]

thx

[@videochel]

dat is not bistabiel

[@onlineelectricwork]

i don't understand

[@zacherievietzke4632]

𝘱𝘳𝘰𝘮𝘰𝘴𝘮 😑