Rate this Video.. Scooty pep plus carburetor cleaning 1: star(Phillips screwdriver) screw driver. 2: 10 mm spanner. 3: petrol or kerosene for cleaning. 4: WD-40 to clean jets. 3:
thank you faddy781..because I faced a such a big trouble today morning..our road coverd with 3ft of flood water..I drive my scooty pep+ throug it with out stoping,after little bit laater my bike slow down and stoped engin suddenly,,so i push it out of water and try to start..about 3hours I stugle with my bike's kik,,so i sqeez the air filter and reset it and checked spark plug,,then i try.so it get start but when i try to race it stops engine so..the error with karbulator..it fill with water...so this video helps me to reset my bikes karbutaror ,1st time my self
That's grt . my video helps others, which is good news for me.that i helped some one with my knowledge. ur air filter and carb got filled with water. cleaning them and dry out make ur pep run again.
Konsi company ka carburettor best hai Scooty pep ke liye! Aur ek sawal Ki kya Scooty pep and pep plus ka carburettor kya alag hota hai. Mere paas only pep Hai
Sir please Give me solution. I had Scooty Pep and It starts but turn off when Throttle is given. I had cleaned the carburettor but I had found a small yellow ring Which i don't know where it is placed and i had fit carburettor Without small yellow ring and The Scooty doesn't start Of we put Hand On air Filter side then it starts with full race and turn off automatically after 4-5 sec and petrol Came on Air filter side if we out hand on air filter side of carburettor. Please give me solution 🙏🙏
Close air screw. Clock wise. When it close fully then open it 1 ½ rotation. That is 360° full turn, from point of start and again half turn. It should work. If not then take to near bike mechanic.
There are 2 screw one with spring. That is idle screw. If you have disturbed that also then open it few truns and Star bike. If you feel your bike on higher rpm the close slowly for idle speed.
I am having problems with starting the scooty. The battery is dead, neither the self start is working nor kick start. Earlier mechanic said it was a battery problem, then after recharging the battery the problem recurred within 48hrs. Later he mentioned there's a problem with the oil seal, it needs to be replaced. I couldn't find the required new parts in my city. I am also doubtful that the mechanic is able to pin point the real problem. Do you have any idea what could be the issue? This problem has been recurring for the past 3 years.
Gadget U like name say "over flow" agar carburettor mai flot valve teek se kam nahi ker raha tho petrol jaada bher jaiga. Tab over flow se bahar nikal jaiga.
@@srikanthraju4261 did the problem get solved. I have the same problem. Scooty works well for 10 mins and after that starts suffocating. If i accelerate full throttle, it takes good pickup, but when at 30- 40 speed it kind of tries to stop or slow down even if i accelerate. I have changed the spark plug, put on the breather pipe which was damaged and also cleaned the air filter. But still the issue persists. Yet to clean the carburetor
this is bit a complex job in scooty.but we can do it. need mileage measuring can or u have to make one. mileage measuring can cost 80-120 rupees or so. u might have seen in mechanic shop. u have to fill 100ml petrol and measure reading in ur bike speedometer. connecting pipe to carb. its a bit big process u can understand only by video. i will make soon.
If you're Air fuel mixture screw was distributed then you have to correct it. You have to close screw in clockwise , when it stops, then turn anticlockwise direction to open. You have to turn (1 1/2) one and half turn. i.e one complete 360 degree turn and again half turn. You can open bit more. If you have distrub ideal screw then adjust that also. For ideling.hope you understand.
my scooty was kept ideal for nearly 9months.. i tried starting now.. battery is completely down.. tried kicking do many times, nearly morethan a hour and its got started. but when i release the accelerator, then the engine getting stopped.. getting a different odour from silencer. cleaned carburetor and air filter. that doesnt helped. any idea what will be the problem??
+Anish Vijayan : better clean spark plug once. and check the gap. i suggest you to change engine oil and transmission oil too. over ideal period oil absorb moisture from air and degrade its property. and get your battery charged.
+faddy781 i have saw your spark plug removal video, but didnt show what to do after removing the spark plug. how to check the gap and clean the spark plug. i have watched your engine oil change video, can you tell me how to insert the filter back, is it just a insert type and close the drain cap or anything tricky.. can you tell me how to change transmission fuild too :). thanks for your effort in making all this videos.. it was helpful.
+Anish Vijayan : to clean spark plug use metal brush or any old brake cable of bike. cut the cable n 4 or 5 strands and put in plug gap. then rinse with petrol. use ur ATM card or Credit card to check gap in plug. gap between center electrode and ground electrode will be card gap. oil filter is just insert type n close drain cap.
Relay is electronic choke hai. engine mai temperature sensor hai jo ki temp.. ko read ker ta hai. agar temp.. kam hai (cold condition) to phir relay ON hoga. or extra petrol bejega. to quick start the engine. normal gadi mai hum choke wire ko pull ker te hai jab gadi cold ho. like early morning in winter.. scooty mai automatic hai. hope you got answer.
hello tina. you have to adjust air fuel mixture screw. for scooty pep + its one and half turns. after full closed. that means when you turn air fuel mixture screw close completely, then again open that screw one and half turn (1 1/2) you can open+1 turn also extra. but for Zest may b same i guess. hope this will work for you.
cleaning silencer is not good idea for 4stroke engines. if u remove and clean with water, it get rust and may damage. for 2 stroke engine silencer get wet with engine oil and carbon. so need to burn time to time.
sir why the vehicle is making a double sound , u know in the starting when we purchase a new one it doesn't but in the video the silencer or something i making a double sound
thanks. Air filter can b clean every 2k km run. if u drive in dusty roads then early. carb cleaning is not regular. it's a last step. if u feel jets block then u have to clean.
Indeed great video thanks for it. would u please explain what amount of petrol drain is acceptable from overflow nozzle which was located above fuel inlet hose.. in my case the drain nozzle is always wet but not leaking drops, only thin layer of petrol on the nozzle. i changed float needle also, but not succeeded so far. Last week my pep hit lowest on mileage just about 24 kmpl from its best 53 kmpl. So i started to take care the carburetor closely and found ur video was very useful. after carburetor clean and change of needle it hit back 40 kmpl but not above. would u throw me some light on this drain nozzle and electric choke??
Thank you for appreciating. that would create kind a vaccum condition when giving throttle. it all ways littel bit wet. dont worry, its common in all bikes. the overflow tube is beneath the carb.. if that is overflowing while keeping bike in side stand or center stand, then replace needle in carb.. electic choke work when temperature is low. temperrature sensor is fitted in bike which reads oil temp... if temp.. is low ..like in winter or early morning, choke will operate.
Bro, whether carburettor has to be cleaned in regular intervals like every 10k or 20k kms? Or is it only needed when we feel drop in mileage or acceleration?
can you please tell me how to adjust the petrol flow because there're 2 screws to adjust. Which one is for petrol adjust and what is the function of other knob or screw or whatever it is.
+Tejinder Singh Swaraj : To adjust petrol flow for ideal running speed you have to turn the screw. which is in silver colour and having spring in it. To increase speed you have to turn in clock wise. Other screw which is in gold colour(Brass) is for air fuel adjustment screw. If you disturb that screw your scooter mileage will drop. it is factory adjusted to get optimum mileage.
+faddy781 thank you very much Sir. I'm facing another with the scooty. as the idle speed is properly set by the mechanic but now it sometimes increasing when scooty is in idle state. the mechanic checked everything and told the wire is good but problem is in its coils. is this true? can it be the problem, of increase in rpm/race, with the coils?? or is it just the carburettor, since the beginning we never cleaned up the carburettor because at the service centre they never mentioned and never did anything except cleaning the 'air filter' and washing it and refuelling the 'oil'. please reply Sir because I don't believe the people at the service centre anymore because I'm facing this weird problem since the last service.
+Tejinder Singh Swaraj ok. generally when you start engine in cold state and keep riding for 4 to 5 km's, engine get's warm and idle rpm will increase little bit. mechanic will adjust idle rpm only when engine is warm or hot. is your bike start normally in cold start ??... is your bike give jerk or miss fire like thing when you are driving at 40 or 50kmph?? if not then your coil is good. if above things are good, then your air fuel mixture screw (gold color Brass) is disturb in last service hopefully. that need to be adjusted. hope this tips will help you.
+faddy781 yes it give some jerks sometimes if I drive this above 55-60 kmph. so this means changing the coil will fix the problem. thank you for the valuable information. one more question - if the carburetor is dusty/not clean, what problems can I face then.
+Tejinder Singh Swaraj If carburetor is dirty, the jet's in carburetor (brass one Its having small holes in it) are blocked then you will not get petrol properly and may get jerk some times too. you have to clean those Jet's. if you have multi-meter then you can check your coil (HT coil) I dont have time to make video on it so i past link th-cam.com/video/rRQ45lT2d3c/w-d-xo.html you can check above link. its about checking HT coil. Its easy. If your coil shows similar reading then your coil is good.
buenos dias tengo una motocicleta marca scooty tvs 2013 y hace poco le hice cambio de anillos y piston pero quedo botando aceite por un respiradero del motor
Super practicals idea, we appriceat for your explanation also. Thanks a lot.
👍
good video - thanks - shows the internals quite nicely
Work over a metal tray on the floor so you can't lose small parts : ) Excellent helpful video.
True.
Nice video bro
thank you faddy781..because I faced a such a big trouble today morning..our road coverd with 3ft of flood water..I drive my scooty pep+ throug it with out stoping,after little bit laater my bike slow down and stoped engin suddenly,,so i push it out of water and try to start..about 3hours I stugle with my bike's kik,,so i sqeez the air filter and reset it and checked spark plug,,then i try.so it get start but when i try to race it stops engine so..the error with karbulator..it fill with water...so this video helps me to reset my bikes karbutaror ,1st time my self
That's grt . my video helps others, which is good news for me.that i helped some one with my knowledge. ur air filter and carb got filled with water. cleaning them and dry out make ur pep run again.
u can like my video
yes I LIKED that video....
Nice 👍
Konsi company ka carburettor best hai Scooty pep ke liye!
Aur ek sawal Ki kya Scooty pep and pep plus ka carburettor kya alag hota hai.
Mere paas only pep Hai
Go for company carburettor. Both are same for pep and pep+
@@faddy781 what about UCAL Carburettor
If they make for TVS scooty. Then ok
I cleaned my scooty carburetor like as shown in the video..now the vehicle is not starting.what to do?
😅😂🤣🤣😂😅
Found the solution?
thx brother....kp doing very informative. ..
+Arjun Kk thanku
Sir please Give me solution.
I had Scooty Pep and It starts but turn off when Throttle is given.
I had cleaned the carburettor but I had found a small yellow ring Which i don't know where it is placed and i had fit carburettor Without small yellow ring and The Scooty doesn't start Of we put Hand On air Filter side then it starts with full race and turn off automatically after 4-5 sec and petrol Came on Air filter side if we out hand on air filter side of carburettor.
Please give me solution 🙏🙏
Did you open air screw in carburettor? It's brass screw. Maybe you have changed the position of the screw.
@@faddy781 yes! i Had Opened
The ring is of metal And small
Close air screw. Clock wise. When it close fully then open it 1 ½ rotation. That is 360° full turn, from point of start and again half turn. It should work. If not then take to near bike mechanic.
There are 2 screw one with spring. That is idle screw. If you have disturbed that also then open it few truns and Star bike. If you feel your bike on higher rpm the close slowly for idle speed.
Very helpful. Thanks
My bike has got completely off in switch starter .... can you tell me the reason sir....
Can't understand your question
I am having problems with starting the scooty. The battery is dead, neither the self start is working nor kick start. Earlier mechanic said it was a battery problem, then after recharging the battery the problem recurred within 48hrs. Later he mentioned there's a problem with the oil seal, it needs to be replaced. I couldn't find the required new parts in my city. I am also doubtful that the mechanic is able to pin point the real problem. Do you have any idea what could be the issue? This problem has been recurring for the past 3 years.
Your battery seems to be dead as problem reoccurring in very short time. Clean your Spark plug or change it. Hopefully it solve.
@@faddy781 I have cleaned the Spark plug. The problem still persists.
@@faddy781 I have changed the battery twice already in two years.
@@Caffeined_Soul any major service done to your bike, like engine remove somthing like that . Bike plug is dry or wet like sticky oily.
@@faddy781 no Major servicing done yet except battery replacement. Never replaced Spark plug as well.
by cleaning carb gives u better ideal n pickup. if u have problem with jet block then u have to clean it other wise not necessary to open carb.
What is ideling, are you give me an idea?
Idling speed normally run on low speed without acceleration.
Yh isme upar Jo black pipe voh Mera ghom gya hai toh Kuch Hoga kya
Gadget U new pipe lelo. Spare part shop mai.
Overflow pipe kya krta hai
Gadget U like name say "over flow" agar carburettor mai flot valve teek se kam nahi ker raha tho petrol jaada bher jaiga. Tab over flow se bahar nikal jaiga.
Good
What is the size of the carburettor??
buddy by cleaning it what it will give???
hello sir my scooty pep clean carb today but scooty was not start please tell me what I do
Pls check spark plug. For spark coming or not. If possible clean plug.
Did you adjust air screw??
Does this have engine same as Victor engine with shorter stroke?
really helpful to me today... thank you
Thank u, you can give thumbs up for video
Neatly explained and video graphed.
My TVS scooty streak carburator is cleaned because when applying accelerator on engine it stops at sometimes what can I do at this time
Clean jets and air filter
Very helpfull sirThank you
please tell me mine can hit only 50 kmph it cant go above it
My scooty pep+ is starting well but when I accelerate engine is stopping.pls help me
Clean air filter.
@@frk380 done air cleaner also but same problem repeating after few kilometres like 15-20 km
@@srikanthraju4261 clean carb jets. It will solve mostly.
@@srikanthraju4261 did the problem get solved. I have the same problem. Scooty works well for 10 mins and after that starts suffocating. If i accelerate full throttle, it takes good pickup, but when at 30- 40 speed it kind of tries to stop or slow down even if i accelerate. I have changed the spark plug, put on the breather pipe which was damaged and also cleaned the air filter. But still the issue persists. Yet to clean the carburetor
Yesterday I done carb jet's cleaning in TVs show room,but problem repeated to day please help me
helpful ,
could you please describe a little bit more about how to tube the carb , i am getting a low gas millage .
this is bit a complex job in scooty.but we can do it. need mileage measuring
can or u have to make one. mileage measuring can cost 80-120 rupees or so.
u might have seen in mechanic shop. u have to fill 100ml petrol and measure
reading in ur bike speedometer. connecting pipe to carb. its a bit big process
u can understand only by video. i will make soon.
connect the green wire or carburetor
Rs kay h karbetar ki
My scooty streak does not starting becuse of fault tunning in the carburetor.. how can start it....?
If you're Air fuel mixture screw was distributed then you have to correct it. You have to close screw in clockwise , when it stops, then turn anticlockwise direction to open. You have to turn (1 1/2) one and half turn. i.e one complete 360 degree turn and again half turn. You can open bit more. If you have distrub ideal screw then adjust that also. For ideling.hope you understand.
How to connect break wire
Sir yeska price kiya hay
Thank you
+harish s : you can give thumbs up for video
ha ha...did that too..
plz upload more video in pep itself
thanks buddy
my scooty was kept ideal for nearly 9months.. i tried starting now.. battery is completely down.. tried kicking do many times, nearly morethan a hour and its got started. but when i release the accelerator, then the engine getting stopped.. getting a different odour from silencer. cleaned carburetor and air filter. that doesnt helped. any idea what will be the problem??
+Anish Vijayan : better clean spark plug once. and check the gap. i suggest you to change engine oil and transmission oil too. over ideal period oil absorb moisture from air and degrade its property. and get your battery charged.
+faddy781 i have saw your spark plug removal video, but didnt show what to do after removing the spark plug. how to check the gap and clean the spark plug. i have watched your engine oil change video, can you tell me how to insert the filter back, is it just a insert type and close the drain cap or anything tricky.. can you tell me how to change transmission fuild too :). thanks for your effort in making all this videos.. it was helpful.
+Anish Vijayan : to clean spark plug use metal brush or any old brake cable of bike. cut the cable n 4 or 5 strands and put in plug gap. then rinse with petrol. use ur ATM card or Credit card to check gap in plug. gap between center electrode and ground electrode will be card gap. oil filter is just insert type n close drain cap.
+Anish Vijayan : check this link
th-cam.com/video/XQWQ5k1zYyM/w-d-xo.html
i made for you. give me thumbs up if u like
+faddy781 thank you.. will apply all the tips you suggested and let you know the result.. thanks
Sir carburettor main relay kya kaam karta hai
Relay is electronic choke hai. engine mai temperature sensor hai jo ki temp.. ko read ker ta hai. agar temp.. kam hai (cold condition) to phir relay ON hoga. or extra petrol bejega. to quick start the engine. normal gadi mai hum choke wire ko pull ker te hai jab gadi cold ho. like early morning in winter.. scooty mai automatic hai. hope you got answer.
Are u from Tamil Nadu
I have a Scooty Zest 1 yr old giving a mileage of 33-35km even after tuning.Can you please tell me how to rectify the issue
hello tina. you have to adjust air fuel mixture screw. for scooty pep + its one and half turns. after full closed. that means when you turn air fuel mixture screw close completely, then again open that screw one and half turn (1 1/2)
you can open+1 turn also extra. but for Zest may b same i guess. hope this will work for you.
faddy781 I think that was done at the service centre.Because I find lot of vibration at low speeds as if the engine is struggling
ok. i think your engine is starving for air. adjust ideal screw, if it's not better then clean air filter.
wht is in bottle shampoo water or petrol?
kerosene, u can use petrol also.. plz don't use water or shampoo..
faddy781 thnk u sir
Bhai mere scooty pep me carburetor se petrol leak ho raha hai har jagah se please help
Change gasket kit in carburettor
Naa banddiki petrol thondharaga ipothundhi endhukani
Check for any leaks. If not then ask good mechanic to adjust mileage screw
super
Super
can you make a video of engine removal
how to change spark plug in tvs scooty pep
thank you
Amal Francis
Kindly add how to clean scooty pep plus silencer.
cleaning silencer is not good idea for 4stroke engines. if u remove and clean with water, it get rust and may damage. for 2 stroke engine silencer get wet with engine oil and carbon. so need to burn time to time.
OK. thank you
Can we soak it for few minutes or not?
Kamesh Neymar yes you can
thank uuu sir (things are going good)
and how to repair selfstart
what problem u are facing with selfstart
sir why the vehicle is making a double sound , u know in the starting when we purchase a new one it doesn't but in the video the silencer or something i making a double sound
i did not get you
sir , i did this today but my vehicle is not starting as soon i accelerate it goes off
clean your carb jets properly, and air filter also. adjust idle speed.hope this will solve your problem.
sir every 5 se 6 din ke andar mera pep ka plug bar bar short ho raha he..uska reason kya he?pls bataiye..
jab ki uska piston thic he.
is your plug get wet with oil?? and carbon ??
faddy781 no sir.
+Debasish das . if ur plug get fill with carbon n oily. that means there is oil coming in ur cylinder. and need to check.
if ur plug dry n filled with carbon deposit. then fuel is not burning properly. need to adjust air screw.
faddy781 thank you sir
I have a problem with my tvs scooty problem is that the engine is not starting and by the kick also not start
open spark plug and clean it. check gap. connect plug to connector and kick it. if ur getting spark then fix it. n start again.
Faddy my scooty's ignition switch and bulbget kaput (out of order) in every 2 month is there any solution thank
thanks. Air filter can b clean every 2k km run. if u drive in dusty roads then early. carb cleaning is not regular. it's a last step. if u feel jets block then u have to clean.
may b water get into it and making poor contact.
Sir my Scooty pep is giving very low milage, means about 35-40 kmpl. What's the cause?
could b a multiple causes. dirty air filter. bad tuned carb. maintain recommended air pressure in tyer.
Ok thanks
Bro plz do video for how to clean silencer ty
cleaning silencer is bad idea for 4 stroke engine. for 2 stroke engine silencer is wet with oil n need to burn out oil n carbon time to time.
+Shaik Farookh thkz bro
Indeed great video thanks for it. would u please explain what amount of petrol drain is acceptable from overflow nozzle which was located above fuel inlet hose.. in my case the drain nozzle is always wet but not leaking drops, only thin layer of petrol on the nozzle. i changed float needle also, but not succeeded so far. Last week my pep hit lowest on mileage just about 24 kmpl from its best 53 kmpl. So i started to take care the carburetor closely and found ur video was very useful. after carburetor clean and change of needle it hit back 40 kmpl but not above. would u throw me some light on this drain nozzle and electric choke??
Thank you for appreciating. that would create kind a vaccum condition when giving throttle. it all ways littel bit wet. dont worry, its common in all bikes. the overflow tube is beneath the carb.. if that is overflowing while keeping bike in side stand or center stand, then replace needle in carb.. electic choke work when temperature is low. temperrature sensor is fitted in bike which reads oil temp... if temp.. is low ..like in winter or early morning, choke will operate.
Mu sccoty not starting. Battery is new. I see petro leak in carpurater some saym replace carpurater. Cleaning carpurater can solve the problem.
Take your bike to mechanic
What is the mileage of this scooty?
it very between 47-55
faddy781 okay, thank you
Bro, whether carburettor has to be cleaned in regular intervals like every 10k or 20k kms? Or is it only needed when we feel drop in mileage or acceleration?
No need to clean in regular. If you feel no proper response from carb then u clean.
@@faddy781 ok bro
can you please tell me how to adjust the petrol flow because there're 2 screws to adjust. Which one is for petrol adjust and what is the function of other knob or screw or whatever it is.
+Tejinder Singh Swaraj : To adjust petrol flow for ideal running speed you have to turn the screw. which is in silver colour and having spring in it. To increase speed you have to turn in clock wise. Other screw which is in gold colour(Brass) is for air fuel adjustment screw. If you disturb that screw your scooter mileage will drop. it is factory adjusted to get optimum mileage.
+faddy781 thank you very much Sir.
I'm facing another with the scooty. as the idle speed is properly set by the mechanic but now it sometimes increasing when scooty is in idle state. the mechanic checked everything and told the wire is good but problem is in its coils. is this true? can it be the problem, of increase in rpm/race, with the coils??
or is it just the carburettor, since the beginning we never cleaned up the carburettor because at the service centre they never mentioned and never did anything except cleaning the 'air filter' and washing it and refuelling the 'oil'.
please reply Sir because I don't believe the people at the service centre anymore because I'm facing this weird problem since the last service.
+Tejinder Singh Swaraj ok. generally when you start engine in cold state and keep riding for 4 to 5 km's, engine get's warm and idle rpm will increase little bit. mechanic will adjust idle rpm only when engine is warm or hot. is your bike start normally in cold start ??... is your bike give jerk or miss fire like thing when you are driving at 40 or 50kmph?? if not then your coil is good.
if above things are good, then your air fuel mixture screw (gold color Brass) is disturb in last service hopefully.
that need to be adjusted. hope this tips will help you.
+faddy781 yes it give some jerks sometimes if I drive this above 55-60 kmph. so this means changing the coil will fix the problem.
thank you for the valuable information.
one more question - if the carburetor is dusty/not clean, what problems can I face then.
+Tejinder Singh Swaraj If carburetor is dirty, the jet's in carburetor (brass one Its having small holes in it) are blocked then you will not get petrol properly and may get jerk some times too. you have to clean those Jet's. if you have multi-meter then you can check your coil (HT coil) I dont have time to make video on it so i past link th-cam.com/video/rRQ45lT2d3c/w-d-xo.html
you can check above link. its about checking HT coil. Its easy. If your coil shows similar reading then your coil is good.
engine removel or engine oil removel
Sar Hindi mein batate to Jyada Achcha rahata hai Taki Sabko Samajh Mein Aaye
Self is workink but not starting
suriya clean spark plug
hi drop by drop petrol leaking in my scooty pep carburetor
check ur fule pipe. if old replace with new one.
check carburetor gasket if old replace.
Meri scooty pept bar bar ruk jarhi
My scooty not giving milage
Bhushan Engg please take it to good mechanic or service centre and explain. Coz they check air filter condition and adjust carb settings.
buenos dias tengo una motocicleta marca scooty tvs 2013 y hace poco le hice cambio de anillos y piston pero quedo botando aceite por un respiradero del motor
cant understand u. can u tell me in english
Super
sir , i did this today but my vehicle is not starting as soon i accelerate it goes off
Super