Jeep Dana 30 Ball Joint and Knuckle Installation
ฝัง
- เผยแพร่เมื่อ 30 ก.ย. 2024
- In this video I have the housing and all associated parts sandblasted and in epoxy primer. Today I am going to go over the correct way to install ball joints and then install the knuckle to the housing.
![[Live] ศึกมหึมันส์มวยไทยสังเวียนเดือด เวทีมวยชั่วคราวสวนสยาม | จันทร์ 30 กันยายน 2567](http://i.ytimg.com/vi/pM1k6f7JXUc/mqdefault.jpg)
Hello, sorry, do you have the ball joint moogs codes?
I have bought Moog parts that were made in China and the quality was pathetic. Be careful when buying Moog they aren’t what they used to be.
Most Moog parts are still made in the USA, like these ball joints in the video. there has been and still are counterfeit moog parts out there, so be careful what you are buying.
I'm looking for the ball joint tool kit that includes the tapered cup to install the upper ball joint. Can you share a kit part number? I would greatly appreciate it. I have a 1979 CJ5 with the Dana 30.
Great video and very informative. I am in the process of rebuilding my Dana 30. I purchased the Moog ball joints and pressed them into the knuckle following your instructions. When I try to tighten down the bottom ball joint nut the ball joint spins. Did you run into this problem?
Thanks,
Mike
Busy in the shop today!! Great video!! Also looking forward to seeing the snow blower doors put back together!!
Do you happen to know if the part number for the uppers were K8194T?
Thank you so much. You saved me so much time effort and I really learned a lot Thank you.
What brand torque wrench do you like best ?
I know this video is old but it is an excellent tutorial. Where can I get the offset ball joint installer for the upper ball joint?
any good tool retailer that sells OTC tools will have the ball joint kit. You can check ebay or amazon, or any tool company that comes up with an internet search.
Nice . From Rossia)
What is the socket you used to set the sleeve on the upper ball joint.?
It is a standard ball joint socket. You can get them from Snap On, OTC and many other retailers.
Thanks Brian
Man I love these vids please don't stop ! Gonna rebuild my transfer case soon
Mayor Fuglycool
lots of videos on the way. Follow along with my transfer case video and you should be fine. A bit more involved than rebuilding a T-90 so take your time when doing the transfer case.
Brian
TC18 looks like a fun project, now that I have some time to work on it, I can get it ready for overdrive as well. Wanted new bearings and seals cause they were shot bad, had oil leaking all over the place after I replaced it with fresh oil. Old oil looked like sand LOL
Yeah the T90 is going to be fun as well, got it stripped out and rdy for the seals. Herm helped me our with all of the seals and what not, going to be putting 90% NOS back into it, as my T90 had really bad pitts on the input shaft.
Mayor Fuglycool
Kalashbash 2020,Texas?
@@arnmjeepcj5416 I was not at Kalash 2020, but will be there for 2021
Mayor Fuglycool
Excellent video Brian. Appreciate you sharing.
thanks for watching, glad you enjoyed the video. Should have this unit finished up in the next video so keep watching.
Brian
I've been looking for 1980s CJ7 parts. Which axles did the 1983 CJ7 have? 33, 35 or 44? and I think it was a 3.07 I also heard about the AMC 20.
the 1983 CJ7 came with a dana 30 front end and an AMC 20 rear end. Switched to a 5 bolt hub in 1981 on the Dana 30. This unit has 3.07 gears in it but others were available.
Are the u-joints on the axle shaft, the same as on the drive shafts?....Hal
no, they are different.
This is a informative video to me a first time jeep owner. the 15 inch pinion load and the ball joint specs would that be the same on 80's cj?
Yes
@@metalshaperJeep Thanks a lot for Answering I do appreciate it!
Great video man 👍