SWAG OFF ROAD PRESS BRAKE GOOSENECK & HEMMING DIES DEMO

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น • 38

  • @jamesbarratt593
    @jamesbarratt593 5 ปีที่แล้ว +2

    I bought the 40 inch finger brake kit and the dies. Fantastic

  • @lucky15driver
    @lucky15driver 5 ปีที่แล้ว +3

    Great video, I recently purchased the ports and table and I'm getting ready to buy the heavy duty finger break.

  • @coolHandLuke5150
    @coolHandLuke5150 5 ปีที่แล้ว +3

    Must have for any DYI fabricator

  • @mikeeagle2653
    @mikeeagle2653 5 ปีที่แล้ว +1

    So the dies actually need to be under sized. To allow for material thickness. So if you need a 1” wide piece out to out and your bending
    1/8 material you would need a die 3/4 wide.

  • @sblack48
    @sblack48 5 ปีที่แล้ว +2

    How do you make a large radius bend, like 1/4"? Is the bottom die have a wide enough V?

    • @blacksheep9734
      @blacksheep9734 5 ปีที่แล้ว

      Rv4 Guy you can get all different sorts of dyes for different applications

    • @mitchdenner9743
      @mitchdenner9743 5 ปีที่แล้ว

      Radiused dies

    • @racinford1
      @racinford1 5 ปีที่แล้ว +1

      I have a large 45* die in the bottom and you can take a dowel pin and weld it on a punch to achieve the radius

  • @retireddriver16
    @retireddriver16 5 ปีที่แล้ว +1

    Sure hope to have that set up some day soon

  • @Texaslife365
    @Texaslife365 ปีที่แล้ว

    Can’t you just use a horizontal bandsaw to cut the solid die into fingers?

    • @Swagoffroad
      @Swagoffroad  ปีที่แล้ว +1

      I apologize, but I'm not quite sure what you mean. Are you saying cut a solid top die Press Brake into smaller segments in order to make it a finger brake? If so, you could but you would then need a clamping bar to hold the fingers.

  • @phillhuddleston9445
    @phillhuddleston9445 5 ปีที่แล้ว +4

    So what are the dies made of?

    • @Swagoffroad
      @Swagoffroad  5 ปีที่แล้ว

      The dies are made with 1/2" plate steel.

    • @tsmartin
      @tsmartin 4 ปีที่แล้ว

      @Archie Bunker They never said this was an industrial tool. It beats ... no pun intended ... trying to bend sheet metal in a bench vise with a block of wood and a hammer.

  • @johnsweeney6072
    @johnsweeney6072 5 ปีที่แล้ว +2

    As me dad said to me you don’t need a long neck to be a goose 👍🇦🇺 nice ideas 💡

  • @heurisvinaz8261
    @heurisvinaz8261 2 ปีที่แล้ว

    How did you guys get the bottle jack to be air operated?

    • @Swagoffroad
      @Swagoffroad  2 ปีที่แล้ว +2

      We replaced the manual bottle jack with a 20 Air Over Hydraulic Jack from Harbor Freight.

  • @TandD1w
    @TandD1w 5 ปีที่แล้ว

    For the press, can you guys develop a set of dies for bending solid round bar? I tried to put a 90 bend in some 1/2” round using the HD press and dented a die.

    • @garethanthonyclark4879
      @garethanthonyclark4879 4 ปีที่แล้ว +1

      Bending round bar is very tricky. I would estimate that in your case you would need a punch with atleast a 6mm radius and also a v of between 60 to 100mm due to the inner radius that it will automatically bend to. Moreover you might need a die with bearings on the shoulder of the die to minimize friction during bending.

  • @SuperKyle309
    @SuperKyle309 5 ปีที่แล้ว +4

    I run a 200 ton press so I find this interesting.

  • @racinford1
    @racinford1 5 ปีที่แล้ว +2

    You being the professional and , well the upper fingers are called PUNCHS the lower are called Die. Male= Punch Female = Die. Just saying.
    your hemming die sets are referred to as Acute angle die sets.
    Each die set will have material clearance to handle the different thickness. The lower die can brake if the material is too thick.

    • @OfficialNetDevil
      @OfficialNetDevil 5 ปีที่แล้ว

      racinford1 I appreciate this comment, I actually learned something neat from it. 🙂
      I didn’t know the punches/dies thing either.

  • @Raumfahrtblei
    @Raumfahrtblei 4 ปีที่แล้ว +1

    maybe... in a future far... far away... the finger press breake is available in Europe.. without 190$ of shipping and taxes..

  • @zps4173
    @zps4173 4 ปีที่แล้ว

    Funny looking goose neck. And that's not all they are for. Yours is cut custom for what ever reason. You should be able to brake a .75 lip 90 and then feed the piece in another 0.75 and brake 90. Up over and down. You can Fab shit like wrecker trucks and service beds and tool boxes and I have always cut my dies to width as needed. The it is referred to as a box break.

  • @OfficialNetDevil
    @OfficialNetDevil 5 ปีที่แล้ว

    Couldn’t I do shallow pans and boxes with the gooseneck set and not need the hemming at all?
    No sarcasm, I’m truly new to the bending world of metal brakes, I bought one from HF and wanna master it. 😊

    • @Swagoffroad
      @Swagoffroad  4 ปีที่แล้ว +1

      Sounds like you got it figured out! All you need for small boxes and pans is a finger brake and maybe some gooseneck dies depending on the size of what you're bending.

    • @JWB671
      @JWB671 4 ปีที่แล้ว

      Swagoffroad.... so how small a box can you bend with the standard finger brakes?

  • @dandannels8821
    @dandannels8821 5 ปีที่แล้ว

    Neet Ben a machinest for 48 years 👍👍👍🛠⚒🛠

  • @SmallPressBrake
    @SmallPressBrake 9 หลายเดือนก่อน

    good job

  • @ooa9123
    @ooa9123 5 ปีที่แล้ว

    Not sure what you're trying to sale a tool or do i have to work to make a tool

    • @Swagoffroad
      @Swagoffroad  5 ปีที่แล้ว

      What we offer are dies that are specifically designed to make certain bends and hems easier to do, that cannot be made with standard or conventional dies.

  • @youngmantiburon
    @youngmantiburon 4 ปีที่แล้ว +2

    I finally got to use my Swag brake press and I love it.

  • @ManjitSingh-wj1il
    @ManjitSingh-wj1il 5 ปีที่แล้ว +1

    Wary nice

  • @jamesbarratt593
    @jamesbarratt593 4 ปีที่แล้ว

    Camera to see your back and then struggle to see past you to the work you did, hmmmmm dude really.
    Also I have your gear here. So I pressed a nut against a finger die and found the nut dented the finger die. I thought those would have been made from tool steel rockwell hard hard. Guess not

  • @m34275
    @m34275 3 ปีที่แล้ว +2

    clickbait nobody died

    • @bpdp379
      @bpdp379 7 หลายเดือนก่อน

      Hemming is obviously the main character….