"locking chuck" = a key "this piece right here" (the two green things that hold the neoprene coupling) = coupling hub (probably a lovejoy s-flex) "this little notch here" = keyway "locking screw" = setscrew (sometimes called a grub screw)
Great video!! If you want to up your game take "as found" measurements with the old motor prior to being pulled,. Measurements would be current draw, alignment numbers, vibration numbers, and temperature numbers. After the new motor is in repeat those measurements so you know how good the install really is. If the vibration sig is 0.1in/sec in any direction attention is required. If any of the measurements are higher than the previous pump motor then that can lead to a fruitful investigation. This is precision maintenance, when many measurements are made and compared to insure the new install is as good or better than the last install. I suggest using the RD Align app or the RD Align Pro app a laser will get to only 0.001" or 0.025mm those sound like small measurements but operating clearance of bearings are measured in micrometers or 0.001 mm, or about 0.000039 inch.
Unfortunately I was taken off this job before I could make a video on it🤷♂️ Thanks for watching! Stay safe out there & stay tuned for new videos every week🔧
As a millwright of considerable years I have to tell you you need the proper names for key ways and hubs and key stock. You would be more professional if you did,
"locking chuck" = a key
"this piece right here" (the two green things that hold the neoprene coupling) = coupling hub (probably a lovejoy s-flex)
"this little notch here" = keyway
"locking screw" = setscrew (sometimes called a grub screw)
Soooooo glad y'all guys did a actual alignment and not just eye balling it.
For sure! This motor is too large to eyeball👀🤣 Thank you for watching!🙏Stay safe out there & stay tuned for new videos every week🔧
Excellent interesting and useful video. Great presentation. Thank you JMT for another amazing video. ⭐️⭐️⭐️⭐️⭐️
Thank you very much! Glad you found this video useful. Glad you enjoyed 🙂👍Stay safe out there & stay tuned for new videos every week🔧
Millwright work at its finest
It is also not a bad idea to use a little never-cease on the shaft when putting the coupling hub on.
Pretty dope content, never see the things happening behind the scenes
Thank you! A lot goes on behind the scenes. Appreciate you watching🙏Stay safe out there & stay tuned for new videos every week🔧
Great video!! If you want to up your game take "as found" measurements with the old motor prior to being pulled,. Measurements would be current draw, alignment numbers, vibration numbers, and temperature numbers. After the new motor is in repeat those measurements so you know how good the install really is. If the vibration sig is 0.1in/sec in any direction attention is required. If any of the measurements are higher than the previous pump motor then that can lead to a fruitful investigation. This is precision maintenance, when many measurements are made and compared to insure the new install is as good or better than the last install. I suggest using the RD Align app or the RD Align Pro app a laser will get to only 0.001" or 0.025mm those sound like small measurements but operating clearance of bearings are measured in micrometers or 0.001 mm, or about 0.000039 inch.
Great video. Seeing this laser alignment tool first time.Hope to see u do a video on the finner details of the same.
Very nice well explained visual video.
Thank you! Appreciate that✌🔧Stay safe out there & stay tuned for new videos every week🔧
nice material! I use antiseize on anything. 👍
Thank you very much Marlon! Nicee//That's a good product right there. Stay safe out there & stay tuned for new videos every week🔧
good stuff man, first time I saw it
Thank you! First time for everything👍🙂✌ Stay tuned for more!
Woodruff key and grub screw are the names your looking for.👍
very good video. any more video about repairing pump ? I like it.
Great video. But can you show how to do a line up with out the lasers
@0:26 that guy got caught slippin
Lmao facts🤣💀
Thank You!!!
Good work
Thank you very much! Appreciate that. Stay safe out there & stay tuned for new videos every week🔧
great video
You use go pro. What is that laser alignement tool and or software?
How do you know when the valud is defectuve?
Grate video can you tell me the name of the tool you used to balance the motor I need to buy one for my job...
Nice. You gonna do any videos on your laser alignment setup?
Unfortunately I was taken off this job before I could make a video on it🤷♂️ Thanks for watching! Stay safe out there & stay tuned for new videos every week🔧
No.64 👍
My brotha💪💪💪
nice piece of tool laser!
For sure!!! Crazy tool👀🔧
I don’t wanna know the price on that alignment tool lol
🤙🤙🤙
✌✌✌
As a millwright of considerable years I have to tell you you need the proper names for key ways and hubs and key stock. You would be more professional if you did,
True, true👍👍👍Appreciate the feedback. Stay safe out there & stay tuned for new videos every week🔧