Toyota Landcruiser 100 series 1998-2002 key fob programming
ฝัง
- เผยแพร่เมื่อ 4 ต.ค. 2024
- Program the key fob to unlock and lock doors. This is done on a 1999 Toyota landcruiser 100 series. Thanks to details from ih8mud.com member Lowbudgetlc100 for the instructions.
forum.ih8mud.co...
o my locks were weak after the 3rd lock/unlock. i did it manually on the driver door.
this is how i did it.
close all doors and open the driver door.
using power door lock on driver side lock all door then manually unlock the driver door
put the remote key in and pull out
lock and unlock the driver door 5 cycle with you hand
close the door and open the door
lock and unlock the driver door 5 cycle with you hand
put the key in turn it "on" position then off and remove
the car should cycle a lock and unlock
press lock and unlock at the same time for 1 second. when releasing press lock again and hold it for 2 seconds.
close driver door and test the remote.
![[UNCUT] “บอสณวัฒน์” ลากไส้!! ใครหนุนหลัง "แม่ตั๊ก ป๋าเบียร์" I คนดังนั่งเคลียร์ I 30 ก.ย. 67](http://i.ytimg.com/vi/QlD7mU2KKRk/mqdefault.jpg)
Thank you this video helped us to programme the keys for the automatic locks for the doors, however we had to do another routine to code to the immobiliser, which was just as easy to follow but from a different video.
I am so happy because between the 2 videos we have managed to save our selfs over £200 for 5 mins work/effort on what the Toyota dealer wanted to charge for a new key and coding.
Thank you again for your help
We have a 2001 Toyota Landcruiser Amazon
Linda Wilkinson what video for the immobilizer did you watch?
you are a HERO! I could not get my 01 4runner into the pairing mode to accept the fob. Using this manual cycle idea made it go in to the pairing mode and my fob paired perfectly. worked first try!
Your halfway door close at 1:34 had ruined my first attempt :D. But it works after 3rd tries. Thanks for your video
Thank you so much! Worked perfectly on my 2000 LC. This was the only method (manually actuating the lock) that would program my key.
2002 Sequoia. Have your master Toyota key at hand (black key)
1. Insert black programmed key into ignition.
2. Press and release accelerator pedal 5 times within 15 seconds of inserting key into ignition.
3. Press and release brake pedal 6 times within 20 seconds of step 2.
4. Remove black key from ignition switch.
5. Insert new unprogrammed key into ignition within 10 seconds of step 4.
6. Press and release accelerator pedal once within 10 seconds of step 5.
7. Once these steps are performed properly you will see the immobilizer warning lamp begin to flash and after one
minute the lamp will stop flashing. Once the immobilizer warning lamp stops flashing you will have ten seconds to insert an additional key to be programmed.
8. Within ten seconds of inserting key into ignition press and release accelerator pedal once.
9. Immobilizer warning lamp will flash and after one minute the lamp will shut off.
Worked like a charm for me....can't believe they try to charge so much for so little! 2002 LC
Man you are the real MVP this worked. Thank you!!!
Saved me $65 at the stealership. Thanks!
It worked great on a 05/2002 land cruiser. Thank you
So just a clarification. When done pressing the lock button on the new fob immediately close and open the door or it doesnt take the programming. At least that's what I spent 15 minutes figuring out. Thanks
Thanks a lot. it worked for a Prado Colorado 2000
It worked the first time thank you very much
Thank you for your video, it did help me to program the key fob for my 2001 LC
Good news!
Worked for me. Thanks for posting
Good video bro, it works in my 99 LC
Well done and thank you so much for posting, very helpful
Thank you...it worked for my 1999 4Runner as well....The other way that the dealer says does not work...
Thank you!
Gabby! This guy is ridiculous!!!!!
Thank you so much I had the key fob for years and try taking it to a locksmith and didn't work until now with your help once again thank you God bless you 🙏🏽
Thanks. its work
Good work
Why did you get a new key fob and where did you get it? My factory key fobs wont lock the door but will unlock them sometimes, the signal seems non existent for the lock button but suspect the buttons are old. I’ve seen some on Amazon but I’m not sure what’s needed to make an Amazon key work after cutting is
Thanks!
Thanks a lot
You left out the last step. After holding lock for two seconds, the last step is to shut the door, then you can test to see if it worked. Do it any sooner and you fail to link the fob.
Thank You for the video.
Sure thing! Hope it helped...
hello does it work with the original key to start the sequence then push the button of the new key fob ?
thanks
I can’t seem to get it. My truck gives me the “lock / unlock” to show its ready… but when I press the buttons on my remote I get no response. Tried over 50 times now ahhhh
same with me..any luck afterwards? did you get it going?
Did you need the master key to program the key?
Yes you will need a master key.
Hell yeah, man!
It works with my 98 Cruiser , now I need to program to turn on the engine, do you have a video for that?
I don't, but you can try www.ih8mud.com, under the 100 series section. There are directions.
more land cruiser tutorials please
Everything works and my car locks and unlocks automatically but nothing happens when i press the keys on the fob. literally nothing. Might be a faulty fob ? I changed the batteries recently the red light comes on but idk why it doesn’t work
Same here. Did you get it to work?
Nope I gave up; I read somewhere that not all models will program even if u get the steps and the car responds to it. Probably gonna need a mechanic to program it but I've lost my key fob since.
Mine is a GXR 6 cylinder petrol for reference
Thanks for the Video! I programmed the key to open the doors but it still does not start the car. It just cranks. Any idea what's going on?
Sounds like that key isn't recognized by the ECU? tlcfaq.com/main/2013/02/key-programming/
Yes, this covers only lock programming and not key to ECU programming, see other comment for directions or search on ih8mud.com in the 100 series help.
hobbes874 this totally worked on my 2000 LC to program the key to start the car. Amazing!
Have you ever done a Toyota Passo?
Is this a cheap Chinese key or does it only work on keys from TOYOTA.
any help appreciated PS nice work
Someone knows if it works to program an imobilizer code in a new key for toyota corolla CE110 ?
Thanks a lot
is it working on 2007 toyota land cruser?
Please tell how to 2003 to 2006 Land cruiser remote programming
හිතුවක් කාරයා try www.ih8mud.com, under the 100 series section. There are directions.
is it working on 2006 toyota land cruser? many thanks
ISLAM rwnaky zhyanma you can, try www.ih8mud.com, under the 100 series section. There are directions.
You can, try www.ih8mud.com, under the 100 series section. There are directions.
can it start car after programing
This is just to program unlock and lock. See other comments on starting vehicle programming or visit ih8mud.com and search 100 series forum.
Sir these key is chang
How did you change the center console to an after market stereo in? Can you help me out with a link or the part number for the Air control unit at the bottom? Mine is at the top above the NAV system. LX 470 2002.
do you know why the key wasnt accepted ?
I was using the unlock/ lock switch. The actuators are slow and this caused enough delay for locks too not allow programming to work. Manually moving the lock fixed this. Hope it helped.
thanks man but i think i found what the problem is
the car key is from a later version of the car and it transmits in different frequency. The transmitter inside the car probably detects it but i rejects it due to that
Thats a key, not a fob
What were you doing wrong initially that did'nt work?
Joseph Linville I was using the unlock/ lock switch. The actuators are slow and this caused enough delay for locks too not allow programming to work. Hope it helped.
I was using the unlock/ lock switch. The actuators are slow and this caused enough delay for locks too not allow programming to work. Hope it helped.
لا يله الى الله
لااله الا الله
🤗
You really talked too much in this one