ATF & acetone. Ball hone. Patience. I'm in love😍 I was so immersed, when I read "Stay Tuned For Part 2" I said NOOOOO😭 This is so excellent, great job.
I'm glad you enjoyed the video! I thought about making it all one video, but it would have been 2 hours long, and I wasn't sure if that would do well or not... I decided to cut the initial video into 2... Part 2 will be up tomorrow, so you won't have to wait long!!
Gasoline and ATF work better then acetone and ATF. The problem with acetone and ATF is that they do not mix and as soon as you put it in the cylinder it separates into a layer of acetone and ATF. Gasoline and ATF will mix and keep creeping into frozen parts better then the separated acetone and ATF.
@@jimthode THAT sounds way better, actually. Anything that will be a Carrier for the anti-corrosion properties of the ATF. Acetone is a go-to ingredient because of it's hygroscopic properties, whereas gasoline will not mix with water. Isopropyl alcohol is actually better for moisture control, but it's not lightly corrosive like acetone, busting up rust. Aromatic hydrocarbons are key for capillary action. The carrier can be changed, but the chief component (ATF) should stay the same.
When the torch shone into the spark plug holes and you could see all that debris in there, I’d have given up at that point. Well done for the perseverance and the skill to revive that basket case of an engine.
Thank you my friend! I always think that if I solve enough problems, at some point i'll have an awesome machine that's better than most I can buy today!
What those 2 goofy looking flat parts with the small slots? One on each side. Those are what you're talking about? Not being sarcastic, I really not sure.
Read more comments and figured it out that it's those flat pieces with the slots. You got my curiosity peaked and set me looking for the correct answer though. 👍
@@williambryant5946 Yes. Or, and I typically do this myself use the side like a hammer. When you're dealing with thousandths it doesn't take much to move that tang.
Mary Shelly would be proud, bringing back the dead No Abby normal brain, just good old know how. This is why I watch you, Desal Creek and Marty T. I am in awe watching you guys bring life back to these perished mechanism
This engine revival was like watching Mustie1 times six. =) Propane dos not need a carburetor cause it always a gas when leave the tank, so it do not need a float chamber, needle, all the jets and small parts. It works with a pressure regulator after the cylinder and a way simple venturi in the intake (it can even be made of plastic). It is so simple that you can keep the carb to have booth combustible system and they will not "see" each other. Thank you for the video!
Hell yeah!!!!! It started!!! You did a GREAT job in the field, cleaning that head, piston sleeves, etc! Your "can do" attitude is pretty strong! I can't wait for part 2.
I wonder how many machine have gone for scrap due to a locked up engine. Your videos and those of others on TH-cam show that with a little dedication and patience it's possible to recover them. I cry for all the lovely machines that have ended their lives as scrap when they could have been saved. Carry on the good work as we all admire your efforts.
It's sofa king amazing you brought that back to life. You ought to be the poster child of hard work and perseverance. You got a bit lucky that that the valves still seal but you don't know unless you try and you did it. I hope you paid a ridiculously cheap price for it. Congratulations.
Open spark plug hole, I gave up. Can't turn engine, I gave up. Broken Distributor, I gave up. Badly rusted cylinders, I gave up. But I'm glad you stayed in there, very entertaining. You lucked out on distributor. Good to have friends with parts.
A lot of you tubers ask things like “I’m thinking of converting this to propane (or doing some other thing), if you want to see that let me know”. For me, the answer has ALWAYS been a resounding yes!! Pretty much anything that is difficult or expensive or of questionable value...I wanna see someone ELSE do it every time!! Thanks for your content. Very enjoyable.😊👍👍
Your field mechanic skills are impressive. I learn every time I see you work. What I really like is how you think, and explain what you do. You are a thinking man, for sure. And I can get a glimpse of your character in these videos. You don't quit, even if you should sometimes. I like your way of doing things.
You my man have the patience of Job, once that motor didn't turn free I would've pushed it back in to the hedgerow..good job and persistence pays dividends
They're only for spreading the gap open. You try to use it to close the gap and you run the risk of breaking the plug center. I was taught to just tap the hook closed on something solid not beat the plug with a hammer. Really plugs usually come new gapped. That's why they have those protective rings on them in the boxes.
This is by far your best video! Thanks for taking the time to give life back to this wonderful piece of machinary! And for taking the time to recording your work!!
I know you are busy other than salvage etc. plus home life, as good and thorough and pickey as you do things you could do any automotive work for hire and do well. Well maybe because of your time involved. You are great I hate it when your videos end. Keep it up and stay safe...thank you
Another dead machine brought back to life - your videos are both entertaining and informative because of the way you explain everything. - Thank You for your videos!!!
That is skilled craftmanship, right there. Both tape and hammer used. After many years exposed to weather and this machine is in pretty good shape. Imagine modern forklift full of electronic left outside for several years like that.
I often think that when we take something that was basically thrown out and left to rot, then somebody like this guy puts love and sweat and gets them working again. These machines are smiling. It just me.
I like your attitude, never give or gave up even toward case like this, at first in my point of view, there was no chance what so ever to bring the life back to the engine like that but to my surprise you did it perfectly, excellent job, you are good.
These continental flathead 4 cylinder and 6 cylinders will literally run forever. Had a 1960s Hyster 5000 pound truck, sat for years upon years. Jumped the battery, still runs better than any of the new hysters.
Had one exactly identical that fork lift , Great fork lift . One foot pedal is the brake and the other disconnects the drive so you can rev the engine to increase hydraulics to the lift mast . As long as you stay on hard ground you can get around very well . get it stuck or unload one drive wheel and you'll have to crib it or pull it back on hard ground to get traction . Enjoy your vintage fork lift .
This might be your best revival video so far, my jaw dropped at the end when this engine started and ran, this simply cant run considering how it looked when you started :)
That was cool glad you got it running been Awesome if we could see you driving it some . But anyway great job on cleaning it up getting it to run . Stay Awesome my friend.
Man!... you are either a hero or a glutton for punishment. Probably a bit of both in my opinion. I would have walked away after seeing the missing spark plugs. This is almost as good as the Old Red project. Can't wait for the next episode.
Please do not stop making these videos, i would do this kind of stuff my self but i have no where to store a forklift or a need for one so i just like watching someone else do this
When you announced it was gas powered, my first thought was 'so where is the LPG bottle mounted?'. Then I realised, 'yes,of course, it's what we call a petrol engine here in the UK'.
Which I always thought was retarded since petrol is short for petroleum and kerosene, diesel, gasoline etc etc all comes from it but you insist on calling only gasoline engines "patrol". Idiocy.
Keep up the great work! Hyster forklifts are tough! Once you get used to the pedal...think it's called monotrol...you'll love it. Great size machine that will be very usefull for the restorations that you do. Better than a new machine, no computer to not work.
@salvage Workshop im a forklift mechanic and all your going to need is an lp converter, a water line coming in and out, and solenoid to shut the fuel off, and a regulator. your biggest obstacle will be if it ever backfires if blow the diaphragm out in the lp converter/ diffuser.. It shouldnt be a problem to do what you want to do. the modern stuff like hyster and toyota are still run just like this only they have more sensors.
I have one of those spark plug gauges. As far as I know, the notches in the metal tabs are meant to be used to grab the bit of metal on the plug and bend it. A most enjoyable video.
my wife is laughing at me as i watch this. i have a 1944 3000lb Clark forklift, with solid, slick warehouse tires, and a gravel lot. i've spent more than a few hours and four letter words dragging it out with the truck...and i have found that having my forklift run on gasoline is way more conveinient than propane. no cylinder to fill/exchange, i can get fuel anytime and i can put it as much or as little as i want.
Do like your videos they're such a relief I thought those kind of things only happened to me the original task turns into at least two others great work keep it up
I've been binge watching your uploads, and I gotta tell you that your content is SOOO good, and so much better than when you first started without any narration. As I watched stuff like the coal fired forge or the arbor press, I seriously wished you were explaining a bit more about the machines and how they worked and what your plan was to deal with and fix all the issues. Thank you for sticking to this and for all that you are doing.
SIR, I have known mechanics twice your age who have less all around skill in diagnosing a problem and figuring out how to solve it without going out for some super expensive part (Distributor as an example) WELL DONE
Incredible in-depth teardown & cleaning - great work. Amazed that you pulled the water pump and head to get where you needed to reach. Naturally, we assume you change the oil before a starting attempt, knowing not only is the oil high from floating on top if rainwater but you'd added more than a bit of ATF past the rings to the crankcase. Thanks for sharing your hard work and are able to hint at the old girl coming to life ahead!
Thanks for watching Brian! I really WANTED this machine to work, so i was totally up for the elbow greaseit needed to come back to life!! Part 2 is up if you haven't seen it yet!
Just redid the top end on one of these engines last year. Take off the vavlecase cover and check that none of the springs are broken. These motors tend to collect moisture and rust out the springs until they break. We had at least half broken this way, and one bent valve. Some parts are still available for these motors, others are VERY hard to find or expensive. If you have to replace a valve, do yourself a favor and get a flathead-style (L-head) valvespring compressor. It makes the job that much easier.
spark plug gap adjustment. Those flat tabs with notches on your gap tool are for gripping the ground tab and opening or closing the gap. No need for a hammer and putty knife....
Absolutely love all your videos man! Especially these old machine “restorations”! I’m a young guy from Michigan going to school to work on heavy equipment! I learn a lot from your videos as well. Keep it up 👍🏻
Don't throw that broken distributor housing away it's definitely fixable it's very easy. Fine rescue you have there it will serve you well for many years to come
Great video! The second Hercules/Continental redo I have watched this week. They are fantastic engines. Combines, Jeeps, generators, tractors, and now fork lifts. You do an excellent video presentation. Anxious to see how old red is coming.
Hahaha!! This is why I don't gamble...I would have bet the farm that you couldn't get those pistons freed-up without ruining the rings and cylinder walls. I'm not gonna spoil the ending, which blew my mind. Those continental engines are tanks.
Thank you for NOT adding stupid background music, Thank you for NOT filming your dogs or cats, Thank you for NOT filming your children. Craftsmanskills only... Brilliant video
I work at a scrap yard. We have three forklifts. All of them were left there as scrap but with some effort they were put into service. Anyway, the scrap yard saved them so "heading to the scrap yard" was the best end to live the rest of their arduous life. And they like it, I mean, with all the abuse of being overloaded and run with low oil and water while on pothole filled asphalt is better than engine up at the business end of a furnace.
Propane is a good idea you just have to buy a kit to change over. About a 90 min job at most. That's a good lift I had one 20 years always did me good.
Congratulations on getting her running! I have a Tow Motor slightly smaller than that but pneumatic front drive tires and solid rear and I get stuck a lot with it, but the best thing is to have a load on the front forks to help you get traction because of all the counter weight in the back.
I used a forklift in a scrap yard very much like this here one but we had dual wheels on it and never had any problems moving around but then the steelyard had very hard ground with a lot of metal being thrown on it and being buried!
ATF & acetone. Ball hone. Patience. I'm in love😍
I was so immersed, when I read "Stay Tuned For Part 2" I said NOOOOO😭
This is so excellent, great job.
I'm glad you enjoyed the video! I thought about making it all one video, but it would have been 2 hours long, and I wasn't sure if that would do well or not... I decided to cut the initial video into 2... Part 2 will be up tomorrow, so you won't have to wait long!!
Gasoline and ATF work better then acetone and ATF. The problem with acetone and ATF is that they do not mix and as soon as you put it in the cylinder it separates into a layer of acetone and ATF. Gasoline and ATF will mix and keep creeping into frozen parts better then the separated acetone and ATF.
@@jimthode THAT sounds way better, actually. Anything that will be a Carrier for the anti-corrosion properties of the ATF. Acetone is a go-to ingredient because of it's hygroscopic properties, whereas gasoline will not mix with water. Isopropyl alcohol is actually better for moisture control, but it's not lightly corrosive like acetone, busting up rust. Aromatic hydrocarbons are key for capillary action. The carrier can be changed, but the chief component (ATF) should stay the same.
@@SalvageWorkshop it happened 10 hours ago... so it's ok, lets make some coffee to wait for another 14...
When the torch shone into the spark plug holes and you could see all that debris in there, I’d have given up at that point. Well done for the perseverance and the skill to revive that basket case of an engine.
Man, I have never seen perseverance like this. You gave 1000%
Thank you my friend! I always think that if I solve enough problems, at some point i'll have an awesome machine that's better than most I can buy today!
When you were using a hammer to tap the spark plug gap and said there probably a better tool, it’s right on the gap gauge itself.
Well go figure! Of course they already thought of that! lol!
What those 2 goofy looking flat parts with the small slots? One on each side. Those are what you're talking about? Not being sarcastic, I really not sure.
Read more comments and figured it out that it's those flat pieces with the slots. You got my curiosity peaked and set me looking for the correct answer though. 👍
@@williambryant5946 Yes. Or, and I typically do this myself use the side like a hammer. When you're dealing with thousandths it doesn't take much to move that tang.
That tool only opens them up. You still tap the hook closed. But you can just tap the hook on something solid.
Those old motors Are indestructible....Good job on saving her...Great Video..
OMG...just watched and I can't believe at the end you show that thing running. Awesome work...
I know!! Crazy right! Tune in tomorrow and you'll see it drive home too!
Don't let him lie to you. His buddy swapped the motor off camera.
Am I the only one who yelled "YEAH!!!" when it started to move? Awesome job!
Lightning whirler, make-it-happener. Have you been watching vice grip garage!
Of course i have! Derek is AWESOME!
Hell yeah
#1
....good one, always nice to try to bring life back into old iron,,,stay safe..
Mary Shelly would be proud, bringing back the dead No Abby normal brain, just good old know how. This is why I watch you, Desal Creek and Marty T. I am in awe watching you guys bring life back to these perished mechanism
I think you are the right person to save this fork lift. GOD bless.
Thank you my friend!
LOOOOOOVE these nice long videos! Thank you sir!
Yes- I commented and haven't even watched yet. That's how confident I am that I will love the video.
Same here
This engine revival was like watching Mustie1 times six. =)
Propane dos not need a carburetor cause it always a gas when leave the tank, so it do not need a float chamber, needle, all the jets and small parts. It works with a pressure regulator after the cylinder and a way simple venturi in the intake (it can even be made of plastic). It is so simple that you can keep the carb to have booth combustible system and they will not "see" each other. Thank you for the video!
Hell yeah!!!!! It started!!!
You did a GREAT job in the field, cleaning that head, piston sleeves, etc! Your "can do" attitude is pretty strong! I can't wait for part 2.
I wonder how many machine have gone for scrap due to a locked up engine. Your videos and those of others on TH-cam show that with a little dedication and patience it's possible to recover them. I cry for all the lovely machines that have ended their lives as scrap when they could have been saved. Carry on the good work as we all admire your efforts.
It's sofa king amazing you brought that back to life. You ought to be the poster child of hard work and perseverance. You got a bit lucky that that the valves still seal but you don't know unless you try and you did it. I hope you paid a ridiculously cheap price for it. Congratulations.
Open spark plug hole, I gave up. Can't turn engine, I gave up. Broken Distributor, I gave up. Badly rusted cylinders, I gave up. But I'm glad you stayed in there, very entertaining. You lucked out on distributor. Good to have friends with parts.
A lot of you tubers ask things like “I’m thinking of converting this to propane (or doing some other thing), if you want to see that let me know”. For me, the answer has ALWAYS been a resounding yes!! Pretty much anything that is difficult or expensive or of questionable value...I wanna see someone ELSE do it every time!! Thanks for your content. Very enjoyable.😊👍👍
Your field mechanic skills are impressive. I learn every time I see you work. What I really like is how you think, and explain what you do. You are a thinking man, for sure. And I can get a glimpse of your character in these videos. You don't quit, even if you should sometimes. I like your way of doing things.
I appreciate that! Thank you my friend!
I have no idea why this channel fascinates me. But it does 😂.
I so look forward to your uploads.💙
my life is meaningless without news of Old Red T-T Hurry for a new videos!
Wow, I have this same model, These things are tanks. No brakes however, maybe you will take on that task. Great video!
You my man have the patience of Job, once that motor didn't turn free I would've pushed it back in to the hedgerow..good job and persistence pays dividends
The small notches on the side of the wire plug gage are for bending (rather than hammering) the side electrode to adjust the gap...
Beat me to it 😀
They're only for spreading the gap open. You try to use it to close the gap and you run the risk of breaking the plug center. I was taught to just tap the hook closed on something solid not beat the plug with a hammer. Really plugs usually come new gapped. That's why they have those protective rings on them in the boxes.
This is by far your best video! Thanks for taking the time to give life back to this wonderful piece of machinary! And for taking the time to recording your work!!
I know you are busy other than salvage etc. plus home life, as good and thorough and pickey as you do things you could do any automotive work for hire and do well. Well maybe because of your time involved. You are great I hate it when your videos end. Keep it up and stay safe...thank you
GREAT STUFF, dont keep us waiting to long for the next installment
Another dead machine brought back to life - your videos are both entertaining and informative because of the way you explain everything. - Thank You for your videos!!!
"We're gonna smack it, just once!" *Proceeds to smack it 1200 times*
Math be hard.
No
@@jamesbrumfield8181 the powerless and weak say no. It takes an individual of means and courage to say yes.
That is skilled craftmanship, right there. Both tape and hammer used. After many years exposed to weather and this machine is in pretty good shape. Imagine modern forklift full of electronic left outside for several years like that.
CAN i use that fle hone for my toilet?
I often think that when we take something that was basically thrown out and left to rot, then somebody like this guy puts love and sweat and gets them working again. These machines are smiling. It just me.
I like your attitude, never give or gave up even toward case like this, at first in my point of view, there was no chance what so ever to bring the life back to the engine like that but to my surprise you did it perfectly, excellent job, you are good.
That was awesome. I cant wait for part 2. Hope its soon! Hi from county Cork in Ireland.
Awesome! Glad you enjoyed it! Part 2 will be posted tomorrow!
@@SalvageWorkshop Yay thats great news. Thanks
Love the sound of those continental 6 cyl lumps fond memories of them in 70s and 80s
These continental flathead 4 cylinder and 6 cylinders will literally run forever. Had a 1960s Hyster 5000 pound truck, sat for years upon years. Jumped the battery, still runs better than any of the new hysters.
It is so satisfying to see a machine brought back from certain death!
I'm pretty sure the "half axel" is some sort of figure skating move where the "half axle" is a forklift part.. 😁
Thoroughly enjoyable. You have a lot of patience and always amazed at your cleaning and rebuilding skills. Looking forward to part 2.
So nice to see repair not just replace.
Had one exactly identical that fork lift , Great fork lift . One foot pedal is the brake and the other disconnects the drive so you can rev the engine to increase hydraulics to the lift mast . As long as you stay on hard ground you can get around very well . get it stuck or unload one drive wheel and you'll have to crib it or pull it back on hard ground to get traction . Enjoy your vintage fork lift .
This might be your best revival video so far, my jaw dropped at the end when this engine started and ran, this simply cant run considering how it looked when you started :)
Thank you my friend! Go check out part 2 for the rest of the story!
That was cool glad you got it running been Awesome if we could see you driving it some . But anyway great job on cleaning it up getting it to run . Stay Awesome my friend.
Man!... you are either a hero or a glutton for punishment. Probably a bit of both in my opinion. I would have walked away after seeing the missing spark plugs. This is almost as good as the Old Red project. Can't wait for the next episode.
Really enjoyed your video. Please start protecting your hands from the chemicals and solvents
Please do not stop making these videos, i would do this kind of stuff my self but i have no where to store a forklift or a need for one so i just like watching someone else do this
Glad you are enjoying the videos!
Nothing like someone with skills making old gold work again
You got to give this guy credit.
Thank you. Love your mechanican. Congrats on the fix. Trusting the Traxcavator is well and mended or on the mend. Ron
When you announced it was gas powered, my first thought was 'so where is the LPG bottle mounted?'.
Then I realised, 'yes,of course, it's what we call a petrol engine here in the UK'.
@@garymallard4699 I think you'll find petrol is your gasoline.
@@garymallard4699 I wasn't being facetious. You actually have it right - gasoline is the real name. Petrol is a trade name.
Which I always thought was retarded since petrol is short for petroleum and kerosene, diesel, gasoline etc etc all comes from it but you insist on calling only gasoline engines "patrol". Idiocy.
Thanks for posting and sharing. You make it all seem doable! I was NOT expecting what you showed at the conclusion!!!
When it comes to breaking the pistons free. I find using a 50 foot pole on the end of a wrench works best.
Keep up the great work! Hyster forklifts are tough! Once you get used to the pedal...think it's called monotrol...you'll love it. Great size machine that will be very usefull for the restorations that you do. Better than a new machine, no computer to not work.
On video your bench always looks like you're working outside in the snow! Thanks, great, love it!
Some hard work bringing back some life out of a good forklift. Nice job.
Excellent !! I love it and I am off to part 2 for the finish !! Great work !!
@salvage Workshop im a forklift mechanic and all your going to need is an lp converter, a water line coming in and out, and solenoid to shut the fuel off, and a regulator. your biggest obstacle will be if it ever backfires if blow the diaphragm out in the lp converter/ diffuser.. It shouldnt be a problem to do what you want to do. the modern stuff like hyster and toyota are still run just like this only they have more sensors.
NICE video! Excellent lighting, clarity, and focus! That engine looks beautiful and I'm sure will run like a champ. Great job!
I have one of those spark plug gauges. As far as I know, the notches in the metal tabs are meant to be used to grab the bit of metal on the plug and bend it. A most enjoyable video.
You did a great job cleaning that engine up. That was a lot of man hours. And a lot of Brake Cleaner.
Ain't nothing you can't do in an afternoon while tying one on.
my wife is laughing at me as i watch this. i have a 1944 3000lb Clark forklift, with solid, slick warehouse tires, and a gravel lot. i've spent more than a few hours and four letter words dragging it out with the truck...and i have found that having my forklift run on gasoline is way more conveinient than propane. no cylinder to fill/exchange, i can get fuel anytime and i can put it as much or as little as i want.
Do like your videos they're such a relief I thought those kind of things only happened to me the original task turns into at least two others great work keep it up
Excellent work👍👍👍. Thanks for sharing
Great work. 🔨🔧🔩
Thanks so much for sharing. 😎👌🏼
You have so many projects going and I am happy to watch what ever you are working on.
I've been binge watching your uploads, and I gotta tell you that your content is SOOO good, and so much better than when you first started without any narration. As I watched stuff like the coal fired forge or the arbor press, I seriously wished you were explaining a bit more about the machines and how they worked and what your plan was to deal with and fix all the issues. Thank you for sticking to this and for all that you are doing.
SIR, I have known mechanics twice your age who have less all around skill in diagnosing a problem and figuring out how to solve it without going out for some super expensive part (Distributor as an example) WELL DONE
Incredible in-depth teardown & cleaning - great work. Amazed that you pulled the water pump and head to get where you needed to reach. Naturally, we assume you change the oil before a starting attempt, knowing not only is the oil high from floating on top if rainwater but you'd added more than a bit of ATF past the rings to the crankcase. Thanks for sharing your hard work and are able to hint at the old girl coming to life ahead!
Thanks for watching Brian! I really WANTED this machine to work, so i was totally up for the elbow greaseit needed to come back to life!! Part 2 is up if you haven't seen it yet!
The little flat blade with the slots is for opening and closing the gap on the spark plugs
love the "distributor removal face"!
Loved the video. If anyone has earned a PhD in wire wheel and brush, it’s you!
Lol... oh i earned that YEARS ago!! If only i had a barrel of all the old used up rotary wire brushes ive finishwd off ! It would be crazy!
The one and only lightning whirler 😂
Watching you clean stuff is great for my OCD.
Really good video and now waiting impatiently for part 2. Thanks for an awesome video.
Watching your videos makes me feel young again, I used to love the challenge of doing things
Just redid the top end on one of these engines last year.
Take off the vavlecase cover and check that none of the springs are broken. These motors tend to collect moisture and rust out the springs until they break. We had at least half broken this way, and one bent valve. Some parts are still available for these motors, others are VERY hard to find or expensive.
If you have to replace a valve, do yourself a favor and get a flathead-style (L-head) valvespring compressor. It makes the job that much easier.
Good video and well done, you took you're time and no shortcuts, cleaned well, explained well and thank you for sharing! :)
That will clear itself up those motors are beasts....
Excellent work. First time viewer here; I subscribed 20 mins. in.
spark plug gap adjustment. Those flat tabs with notches on your gap tool are for gripping the ground tab and opening or closing the gap. No need for a hammer and putty knife....
Those Continental flatheads are some really nice engines i must say
Absolutely love all your videos man! Especially these old machine “restorations”! I’m a young guy from Michigan going to school to work on heavy equipment! I learn a lot from your videos as well. Keep it up 👍🏻
The flathead contenintal is a beast of an engine! I suggest running it on the rich side if you can to prevent valve issues
Nice work Matt! Thanks for the episode
Yeahh. That Hyster Rocks everywhere. Great machine. I don't understand why should somebody scrap it 🙍🙍🙍. Please go on 💪💪💪
Don't throw that broken distributor housing away it's definitely fixable it's very easy. Fine rescue you have there it will serve you well for many years to come
Great video! The second Hercules/Continental redo I have watched this week. They are fantastic engines. Combines, Jeeps, generators, tractors, and now fork lifts. You do an excellent video presentation. Anxious to see how old red is coming.
Hahaha!! This is why I don't gamble...I would have bet the farm that you couldn't get those pistons freed-up without ruining the rings and cylinder walls. I'm not gonna spoil the ending, which blew my mind. Those continental engines are tanks.
Great rescue 👍👍👍cheers Steve🍺🍺🍺
Thank you for NOT adding stupid background music, Thank you for NOT filming your dogs or cats, Thank you for NOT filming your children. Craftsmanskills only... Brilliant video
Brilliant work, well done, looking forward to Part 2, thank you 👍😊
thank your time making awesome videos for us
Oh well i thought the engine would not be saveable so good job😄👍
I work at a scrap yard. We have three forklifts. All of them were left there as scrap but with some effort they were put into service. Anyway, the scrap yard saved them so "heading to the scrap yard" was the best end to live the rest of their arduous life.
And they like it, I mean, with all the abuse of being overloaded and run with low oil and water while on pothole filled asphalt is better than engine up at the business end of a furnace.
Great job very interesting look forward to the next video 🦘🇦🇺👍
As other TH-camrs have said about fork lifts- "If it's not leaking, there's nothing left to leak!"
Well all the old ones I've owned definetly seem to leak!
Thats funny lol
Been driving Hysters since 1999. Worth keeping them going.
You've done a good job on that Machine mate 👍
Propane is a good idea you just have to buy a kit to change over. About a 90 min job at most. That's a good lift I had one 20 years always did me good.
Congratulations on getting her running! I have a Tow Motor slightly smaller than that but pneumatic front drive tires and solid rear and I get stuck a lot with it, but the best thing is to have a load on the front forks to help you get traction because of all the counter weight in the back.
I used a forklift in a scrap yard very much like this here one but we had dual wheels on it and never had any problems moving around but then the steelyard had very hard ground with a lot of metal being thrown on it and being buried!
great lift truck have had two of them, not real cheap to fix but can be done on a budget.
Hi buddy. Always love watching you fixing things as you’ve a really good way of explaining what going on 👍🏻 Excellent video. 🏴
I have to say i'm pumped for this series 😀