How to thread a Pfaff 1245-706 Sewing Machine - Car Upholstery
ฝัง
- เผยแพร่เมื่อ 11 ก.ย. 2024
- ✅Any donation to support the channel will be much appreciated!
Paypal : cechaflo@gmail.com
✅Get our courses at: www.cechaflo.com
---------------------------------------------------------------------------------
This video shows according to Pfaff manual how to thread a Pfaff 1245/706.
As we can see, at the beginning of the video this machine uses needles from 110 (European measure) =18(American measure) to 180=24
For this demonstration I have used a 120 needle, and standard upholstery polyester thread 92.
I hope you find it useful!
Cesar
Thank you!! You are the only one that shows the details and goes slow enough for me to thread my machine. 👍
Thank you for your inspiring videos. i am an upholsterer for thirthy years in germany and still learning. so i am very glad that i discovered your channel. anyway, as i see you a are threading in an different way than we do. the most people do it your way, which needs to hold the thread at the beginning so you dont get a mess on the downside of the material. so as i see on 2:27 you dont go over the little pin on the first spring where you ajust the tension. so there is a reason for the pin. just go over the pin and the to the next thing in the front and you will never have to hold the thread anymore at the beginning. it makes everything alot mor easy. for you all the best cheers from germany
I also used to thread passing the thread over the little pin . Perhaps this is a good way to threading. th-cam.com/video/YDiyffeXleg/w-d-xo.htmlsi=l6ItBvrMIEq5gBby&t=507
But I changed my mind since I read the 1245 Pfaff manual.
Chapter 9.06, Page 32
www.manuales.mx/pfaff/1245/manual?p=32
My best wishes! Greetings from Mexico!
Big Big industrial Thank you. Great job in showing how to thread the machine. I am a little slow, but by slowing down the video i could go step by step, seeing your demo and my running to my machine and then back again, then seeing then running back. I do little industrial sewing. Sp, I forget. Now I got this.
I am grateful for your videos, at a time today my phaff 1245 machine was deregulated immediately I remembered your videos I solved the problem many thanks
THANK YOU! I have been fighting thread issues for months with my 1245 and have asked a bunch of questions on a bunch of forums but never got an answer that fixed my problems. This video showed me two slight threading mistakes, that no one else mentioned, that appear to have been causing the issues.
Welcome to this channel anytime!
Please, feel free to ask if any doubt. It would be interesting if you tell us about the two mistakes that probably were causing some issues.
@@Cechaflo I wasn't running the thread through both of the eye holes on the L shaped bracket on the front of the machine. My manual is for a double needle machine and it just shows the thread passing through one hole for each thread so that was how I did it on my single needle machine. Second I was looping the thread behind the pin that aligns the thread tensioners.
Hello Ian, Thanks for telling us what happened. In fact, Pfaff enginners designed every and each hole where thread should pass through. This avoids fraying of thread. As for the thread behind the pin it does not affect not at all. Some machines are threaded behind this small pin.
Have you already seen bobbin winders related video? th-cam.com/video/TCskDG9Ieh4/w-d-xo.html
In a next video, I will show how to adjust tensions, then about how to choose right needles, and so forth.
@@Cechaflo I have watched the bobbin video and look forward to the others as they are very helpful. You had already helped me with a needle issue with this machine previously. I really appreciate the time you take to help others out. Thanks again.
@@iangibbons7942 You are welcome!
GOOD MORNING SIR. BY seeing ur vedio CLIP WE CAN learn A LOT. THANK YOU SIR PLEASE UP LOAD MANY MORE. ĢOD BLESS YOU. 🙏🙏🙏🙏👌👌👌
Dear friend, more related videos are coming over!
Thanks for watching!
Thanks!!
СПАСИБО !
Hello sir, i just got a 1245-706, i’m little lost for the moment. But you already helped me a lot. I’m having problem with the thread , i do everything like you but the thread above get stuk, it’s really hard to pull it, what can i do? Thx.
The issue is the upper thread does not freely run downwards.
Check out one by one, all the holes and slots where the thread passes through.
Perhaps the problem is in the tension disks.
The disk surface should be soft to let the thread slide.
th-cam.com/video/t-0xatZVfVw/w-d-xo.html
Thank you, i’ll try. I’m having issues with this machine, i’ve never used an industriel machine before and i’m sometimes about to give up.
Nice and slow but would be 1000% better if you added some spoken description following your actions. Just a thought
تستحق الاشتؤاك
The video quality was exceptional. What video camera was used here.
Thanks so much for appreciating this video!
The video camera is a Canon VIXIA HF R42 53X ADVANCED ZOOM
My pfaff is identical to yours. I have always used GB needles of the 135 X 17 class. I am sure I remembered reading somewhere this was correct for 1245. Now I am surprised to see in your video you are using 134 X 35. Am I completely wrong? What do you suggest?
Dear Joe, TBH, I have not put attention to needle systems. The needles I am using work out good for my 1245 machine. My machine needles are 43 mm long.
I cannot say with precision if you are wrong or correct.
Please, read these forum posts. It seems some useful information inside:
leatherworker.net/forum/topic/49596-what-exactly-needle-should-i-get-for-pfaff-1245/
Hope it helps.
The 135x17 is 44mm which moves the hook slightly lower in the scarf when I use your size. Both work fine but I'll stick with mine as I dont see a difference in performance. My bigger problem is I need to replace my presser foot bar. I found 2 sources in China but the part they swear is correct is too short and has very little hollow for the center spring. I ruined the screw thread so my presser foot is unstable. I have been getting by with it but It really becomes a problem with piping tunnel feet. Any suggestions on a source that I can actually contact?
@@joefish1498 Dear Joe, I have not not clearly understood the issue. Which screw thread are you referring? Is the little bolt for presser foot (big rear foot) adjustment? If so, I have a solution without buying a new bar.
www.ebay.com/itm/1SET-PRESSER-FOOT-BAR-SCREW-FIT-FOR-PFAFF-1245-706-1246-706-1247-706-/264294915488
www.ebay.com/itm/1SET-PRESSER-FOOT-BAR-SCREW-FOR-PFAFF-1245-706-1246-706-1247-706-/273261191589
It's the shoulder screw that actually holds the rear foot to the bar. I over tightened it and stripped the threads in the bar.
@@joefish1498 It seems I had the same issue when I bought my used machine. The threaded hole (millimetric) housed in the bar was stripped. I bought a flute tap one millimiter thicker approx. and made new thread. To give rounds to the tap I used a pair of pressure pliers. A small lever to hold taps would work out much better. Anyways no much thread to make in that bar hole.
I hope it helps.
hi, at 2:30 the thread isn't supposed to go around the tension wheel up to the little metal pin, resting on it then going down to the second wheel with the spring ?
I use a pfaff 145 and i thread it as I describe above, does I'm doing it wrong ?
Because of, I had another machine trade marks in the past and used to pass the thread around the little steel pin I did the same on my Pfaff 1245 (min Twenty six:45 of this video th-cam.com/video/lGhoOsr91rk/w-d-xo.html)
After reading the 1245 manual I changed my mind and followed the Pfaff rules.
In fact, it does not affect anything and in my particular opinion the thread is guided much better to avoid fraying. It could be thought thread could cut the little pin, but it is a hard steel.
The Pfaff 145 is similar to 1245 and the manual section 8 shows the thread do not pass around the little pin.
www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/pfaff_145-manual-EN.PDF
@@Cechaflo thanks for your answer 🙂
Why aren't you clicking the thread over the pin at the discs ?
It can be with no problem. It seems much better if goes around that pin. I did it before with another machine and with this Pfaff too.
Now, I am following what the Pfaff manual shows: (Please, check number 32 - 9.06)
www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/pfaff_1245_1246-manual-EN.PDF
Hello how are you. I mean, even if we change the box of the thread for the first, it is suitable for it according to what I saw. The box does not match what I used to see. Thank you.
Thanks for watching the video!
Qual tamanho do parafuso da agulha
Ud. pregunta por el tornillo milimétrico que presiona la aguja.
th-cam.com/video/H4sOyVIYHt0/w-d-xo.html De ser asi el grosor Ø es de 2 mm
How much please
This is a used machine and costs approx. 1000 USD
اللايك🌷🌺🌸🌹🥀💮🌻🌼
Thanks for kind remarks!
This is wrong!
I have followed the Pfaff 1245 instruction manual the Pfaff engineers wrote down: chapter 9.05 Threading the needle thread (page 31) file:///C:/Users/Cesar/Downloads/BA_1245_1246_10-15_EN%20(4).pdf
It also works out this other way, without any problem:
th-cam.com/video/lGhoOsr91rk/w-d-xo.htmlsi=o9A6XnlsG07qBtqe&t=1605
See how to make a thread on this link. ://th-cam.com/video/35zxtSRFXwQ/w-d-xo.html
I have already seen it. As mentioned before, I was used to do it that way for a very long time. But after watching the original manual I changed my mind and go according to original Pfaff manual the factory engineers designed for some reason.
Anyways, it does not affect anything, both ways are good.