Excelente trabajo! Es milagroso, que estas máquinas sometidas a un régimen de trabajo muy exigente y con demasiada suciedad de por medio, puedan gracias a gente como tu, seguir trabajando. Cada vez tengo más claro que el mantenimiento adecuado, aumenta la vida y el rendimiento de las mismas. Muchas gracias por mostrar lo que sabes!!
Thanks, I appreciate the crash course. Got to admit I thought you'd have a tough time with those rings, but you got her going, and no leftover parts either, lol
Great Video with manuel in Discription.I stuck that awnry spring on cylinder in a vise and bent the spring, tool went right in,screw came out easy.Thank You for this helpful video im just waiting on my Parts to arrive.
Agreed. Check for local estate sales/auctions in your area. That's where I usually find good deals. If you can get out to an auction thats 45-60 miles from a major city, I think you'll find some good deals
Hello , what do you suggest if the blade doesn’t spin after changing the piston,cylinder and and rings ? I notice a crack in one the springs on the clutch . Could that cause the blade to not spin when giving it throttle ?
Hi. My saw does idle and shut down after using for a few minutes. I replace the cylinder piston, spark plug, air filter, but no the carburetor. Whenever I cut into the block, it loses power. Notice that the cylinder started to feel hot. What is the reason for not idling and overheating?
When 🤔 you installed carberator did you make sure the bottom tab locked in on the cylinder,air leak will fry the piston.Carb screws vibrate loose sometimes,turn em clockwise all the way in,then its 1 1/2 turns counter clockwise each, should start right up and run good.Dont use Chinese parts.40:1 oil mix.
I would double check that you re-installed the pull starter correctly (make sure nothing is binding) - also are you pushing in the decompression button when trying to start it?
![โรงเรียนห้ามรัก โดนจับได้ตาย...!! [เอิร์นไดเม่]](http://i.ytimg.com/vi/4u02Sbr556Q/mqdefault.jpg)
![ตีสิบเดย์ [FULL] | เปิดใจ "อาจารย์ เบียร์ ฅนตื่นธรรม" นักสนทนาธรรมสายดุดัน!](http://i.ytimg.com/vi/vqaBI_mnoDk/mqdefault.jpg)
Excelente trabajo! Es milagroso, que estas máquinas sometidas a un régimen de trabajo muy exigente y con demasiada suciedad de por medio, puedan gracias a gente como tu, seguir trabajando. Cada vez tengo más claro que el mantenimiento adecuado, aumenta la vida y el rendimiento de las mismas. Muchas gracias por mostrar lo que sabes!!
Should be all set now. Good job!
Thanks, I appreciate the crash course. Got to admit I thought you'd have a tough time with those rings, but you got her going, and no leftover parts either, lol
A real video showing the real shit that happens. Great video. Thanks for the info.
Great Video with manuel in Discription.I stuck that awnry spring on cylinder in a vise and bent the spring, tool went right in,screw came out easy.Thank You for this helpful video im just waiting on my Parts to arrive.
Glad it helped
its the same kit for the k770¿
Thanks for sharing. Keeping my eye out for a cheap one, but people on ebay have cottoned on and are selling non runners for stupid money.
Agreed. Check for local estate sales/auctions in your area. That's where I usually find good deals. If you can get out to an auction thats 45-60 miles from a major city, I think you'll find some good deals
Thanks
Bom dia eu tenho uma e preciso de comprar o carburador e o filtro é a capa do filtro.........você pode me indicar um site pra mim comprar as peças
I know you said you "wouldn't go into it", but a clue as to how to get the vibration spring off would be real handy mate?
Put the spring on the cylinder in a vise,bend it ,,wall La,tool goes right in.
Cheers Scott, I worked it out a while back, but thanks for the reply.
Dave.
Hello , what do you suggest if the blade doesn’t spin after changing the piston,cylinder and and rings ? I notice a crack in one the springs on the clutch . Could that cause the blade to not spin when giving it throttle ?
Did you remember to put belt on,sounds like your bottom end is toast.
Hi. My saw does idle and shut down after using for a few minutes. I replace the cylinder piston, spark plug, air filter, but no the carburetor. Whenever I cut into the block, it loses power. Notice that the cylinder started to feel hot. What is the reason for not idling and overheating?
I would check for any air leaks between the air intake and the carb.
When 🤔 you installed carberator did you make sure the bottom tab locked in on the cylinder,air leak will fry the piston.Carb screws vibrate loose sometimes,turn em clockwise all the way in,then its 1 1/2 turns counter clockwise each, should start right up and run good.Dont use Chinese parts.40:1 oil mix.
I installed everything but when I pull the cord to start if stiff what can I do there?
I would double check that you re-installed the pull starter correctly (make sure nothing is binding) - also are you pushing in the decompression button when trying to start it?
@@DMIDoes ok thank you very much I will check thank you again
Can you please put a link for the piston kit you used?
This is the kit I used: www.amazon.com/dp/B01LYZZSGA/
I just picked on up for free because it was seized. What you just replace the engine?
You can replace just the piston and cylinder. Should be able to do that for about $60 and your time.
@@DMIDoes Sweet it's just a matter of getting it cylinder of the piston now hahaha. Cheers for the reply! 👍🏻
Just cut it off with the grinder hahaha 🤣
How long do you figured it took you?
I would estimate it took about 2 hours start to finish. It really wasn't too bad.
💯👍👍👍🤝🤝🤝
whats the part number
Here's a link to the piston kit I used: www.amazon.com/dp/B01LYZZSGA/