Great restoration video! The detailed explanations and clear steps made it easy to follow. Thanks for sharing such informative content. Looking forward to more videos like this!
I found this fascinating. I cannot believe how all the parts were cleaned up and the machine reassembled and worked. My brain would have forgotten where some things went!!
That was not an easy restoration so well done. You surprised me with getting that motor going again, I thought it was beyond repair. Cheers mate, Stuart.
You should not put grease where the bearing sits on the plastic, it should be dry so the bearing outer race stays stationary, only the inner race spins, Grease should be on the gear teeth only.
Its not that the motor is crappy, the previous owner did not maintain it and store it in the proper conditions. Makita stuff from that time was amazing quality..
@@hbrestoration Ключове слово, у вашій відповіді - "не думаю". Для того щоб задуматись, дайте відповідь на питання - з якої причини виготовляють замки, до дужки яких не можливо дотягнутися, ніяким інструментом.
One of the reasons is that batteries like this will have to come with a charger that uses a different voltage in our country. If you need to charge it, you will need an additional power adapter for it, which is quite troublesome. The simple solution is to use a charger adapter that uses a common power source
Step 1. NEVER allow the rusted or corroded mechanism to soak in hot penetrating oils! Breaking off screws and bolts and forcing pieces apart with brute force is much more fun.
@@hbrestorationUltimate bolt removal challenge. A 1946 Willy jeep that had spent about 20 years on beaches. All four brake bleeder fittings were rusted to the point it could have been possible to break them off with our fingers. All four assemblies spent a week immersed in a drum of used motor oil heated with a hot plate. Then each bleeder was heated to almost red and sewing machine oil applied. About 20-40 heat and cool cycles. The challenge: remove all four bleeders with an extra deep socket, no ratchet but only by twisted by hand. No problem at all. One didn't even need the socket - came loose on it's own. Chemically, iron oxide and steel are very different and iron oxides can be broken down to the molecular level, unattached to the steel.
"an extra deep socket" I don't quite understand this. But it seems that method is very useful, perhaps next time I will try it with important details that need to be kept or cannot be replaced.
@@hbrestorationSocket. Just one long enough to get a good grip on with your hand and twist it back and forth. Lots of gentle cautious persuasion. One the part starts to turn just the slightest keep dripping the oil in while lightly heating it. The oil washes away the loosened oxides.
Just a thought try using PB Blaster works amazingly on stubborn and rusted bolts.. Oh and try using a cut up bicycle tube for extra grip on your Vice or add on grips for a vice
@@hbrestoration спасибо за доброе пожелание. Взимно. Сейчас такое время, что время мастеров стоит дорого. Такая реставрация у меня займет примерно 12-18 часов. За это время на основной работе зарабатываю в три раза больше, чем стоит такой инструмент. Я понимаю, что вы это делали для своей души. Для личного удовольствия. Это как самому помыть свою машину. Это как вместо ресторана, самому приготовить барбекю. Всех вам благ от такого же мастера как вы. У вас есть чувство любви, это очень прекрасно.
One of the reasons is that batteries like this will have to come with a charger that uses a different voltage in our country. If you need to charge it, you will need an additional power adapter for it, which is quite troublesome. The simple solution is to use a charger adapter that uses a common power source
@@hbrestoration With 1 GB per second download speeds, I can download an entire blu-ray movie in under 30 seconds. Streaming 4K should be a breeze, sorry , you don't seem to understand internet speeds.
I managed to translate that without looking, one hundred percent correct and I don’t know much Spanish , i am guessing it was a left out in the rain and forgotten. . All the best from England.
It is one of the best restorations I have ever encountered on TH-cam Channel. It is so amazingly done with the original parts of this little tool. I have just subscribed to your channel; I am seeing your channel for the first time, and I can tell you that you're full of originality. Thank you so very much for a restoration well done. ❤
Too slow because you cut battery power in half it seems like if I had to use this one I would just use my muscles and a hammer and get more done sorry but at least you made it work
Судя по началу, это ролик об утилизации. в конце алюминиевые части бросят в печку, обмотку двигателя в цветмет приемку. как из случайно подобранного получить стакан и закуску.
Не дай вам Бог попасть на ТАКОГО "реставратора"!! Любой, кто знаком со слесарным делом, будет в ужасе от той дичи, что творит этот чел!! Так как он относится к механизму -- ЭТО ПРЕСТУПЛЕНИЕ!!!
This kind of thing makes my day because not many people appreciate quality anymore! Nice work
Thank you for appreciating this work ^^ have a nice day
nobody can afford quality anymore..on going to hobo freight.
Great restoration video! The detailed explanations and clear steps made it easy to follow. Thanks for sharing such informative content. Looking forward to more videos like this!
@@diytoptricks thank you ^^
I never thought that motor would work again. Fantastic job.
i think too, Luckily it still works😅
❤❤❤❤❤😂
²q2q2q²q2q2q ah@@hbrestoration
Love no talk no music videos
❤️❤️❤️ have a nice day
I found this fascinating. I cannot believe how all the parts were cleaned up and the machine reassembled and worked.
My brain would have forgotten where some things went!!
Many thanks. have a nice day ^^
When I saw that motor, I was like, "just chuck that in the bin"
me too, but it still seems to work fine 😊
Simplemente admiro tu capacidad tanto en lo mecánico como en lo eléctrico.
Muchas gracias por el vídeo.
thank you ❤️
Fantastic how you restored that rebar cutter to working order. It looks much better and it works like a charm too. Excellent work.
thank you very much ❤️❤️❤️
amazin work, with the way that motor looked, did u find it in a pond lol
thank you 🥰🥰🥰
That was not an easy restoration so well done. You surprised me with getting that motor going again, I thought it was beyond repair.
Cheers mate, Stuart.
I tried, it doesn't seem to be smooth, maybe I should still replace them
@@hbrestorationthe brushes in the motor have probably been damaged in some way :(
I am impressed. This tool looked like it was beyond repair.
Many thank ^^ have a nice day
You should not put grease where the bearing sits on the plastic, it should be dry so the bearing outer race stays stationary, only the inner race spins, Grease should be on the gear teeth only.
Really, I've always done that. Can you specify at what time in the video?
@@hbrestoration Right before you sit the bearings on the plastic housing.
@@Capturing-Memories Thank you
I've never heard of a rebar cutter, but man could I use one.
🥰🥰🥰
An angle grinder is quicker.
machine has 1 unique advantage
HYDRAULICS ARE AWESOME SOO MUCH POWER WITH THIS CRAPPY MOTOR GREAT WORK 😊😊😊😊😊😊😊
thanks ❤️❤️❤️❤️ have a nice day
Its not that the motor is crappy, the previous owner did not maintain it and store it in the proper conditions. Makita stuff from that time was amazing quality..
Почему от такой ржавый? Вы его специально таким сделали? Подобный инструмент используется и хранится под крышей.Как он смог так заржаветь?
I bought it at a used yard, it seemed to be soaked in water from being outdoors and I didn't mean to do that.
Excelente trabajo realizado
🥰🥰🥰 thanks
THANKIOUPR❤❤❤❤❤❤❤❤❤❤❤❤❤❤
❤️❤️❤️
You are very talented. Well done!
thanks ❤️❤️❤️❤️
Наразі я побачив причину, через яку роблять висячі замки, з дужками які ховаються у корпусах таких замків.
What do you mean?🙄
@@hbrestoration Я кажу, що цей інструмент ідеально підходить для руйнування висячих замків, до дужки яких, є доступ.
@@clockmakerify 🤣I don't think anyone will use it to break locks
@@hbrestoration Ключове слово, у вашій відповіді - "не думаю". Для того щоб задуматись, дайте відповідь на питання - з якої причини виготовляють замки, до дужки яких не можливо дотягнутися, ніяким інструментом.
So many parts. Restauration job well done 👍👍👍
thanks 🥰🥰🥰
Wait... YOU CAN REBUILD THOSE BATTERIES!
yeppp
Nice job.
What are the two magnets doing?
It has one use: to suck up metal filings in the oil when the pump is operating
Tous simplement bravo❤🇩🇿
thank you very much ^^
Temizlemede kullandığın kimyasalların isimleri neden belirtmedin?
You can turn on the sub to see the chemical names
should have blue'd motor casing as it will rust again
I applied a layer of anti-slag oil
You put engine oil into a hydraulic system. This can ruin the rubber seals.
Thanks, I'll do better next time
muy buen trabajo ,eso de la bateria me ha gutado muchisimo.
One of the reasons is that batteries like this will have to come with a charger that uses a different voltage in our country. If you need to charge it, you will need an additional power adapter for it, which is quite troublesome. The simple solution is to use a charger adapter that uses a common power source
10/10 buen video 🎉🎉
❤️❤️❤️ thank you
Step 1. NEVER allow the rusted or corroded mechanism to soak in hot penetrating oils! Breaking off screws and bolts and forcing pieces apart with brute force is much more fun.
That screw was subjected to quite a lot of force when cutting, so it was affected
@@hbrestorationUltimate bolt removal challenge. A 1946 Willy jeep that had spent about 20 years on beaches. All four brake bleeder fittings were rusted to the point it could have been possible to break them off with our fingers.
All four assemblies spent a week immersed in a drum of used motor oil heated with a hot plate. Then each bleeder was heated to almost red and sewing machine oil applied. About 20-40 heat and cool cycles.
The challenge: remove all four bleeders with an extra deep socket, no ratchet but only by twisted by hand.
No problem at all. One didn't even need the socket - came loose on it's own.
Chemically, iron oxide and steel are very different and iron oxides can be broken down to the molecular level, unattached to the steel.
"an extra deep socket" I don't quite understand this. But it seems that method is very useful, perhaps next time I will try it with important details that need to be kept or cannot be replaced.
@@hbrestorationSocket. Just one long enough to get a good grip on with your hand and twist it back and forth. Lots of gentle cautious persuasion. One the part starts to turn just the slightest keep dripping the oil in while lightly heating it. The oil washes away the loosened oxides.
Nice job
thanks ❤️❤️❤️
I'd have tossed it in the wheelie bin as soon as I saw that motor. Never been a fan of using WD-40 as a lubricant, since it's a degreaser
I don't use wd 40 for lubrication
Excellent.
Many thanks!
Всё супер. И не знал что есть такая штуковина (((
Особенно впечатлил аппарат для точечной сварки аккумуляторных батарей.
Thank you, hope you will watch more videos on my channel and leave comments like this
те же мысли)
@@vitalik_aka_777 ☺
на пластилине надо было проверять, ну или максимум на сосисках...
good job
thanks ^^
Is that engine oil?😅 Put some hydraulic oil instead.
Temporary use 😂 not available at home
Great, my friend. I think it could still work very well
Thank my friend 🥰🥰🥰 have a nice day
Just a thought try using PB Blaster works amazingly on stubborn and rusted bolts.. Oh and try using a cut up bicycle tube for extra grip on your Vice or add on grips for a vice
What is PB Blaster? thank you for giving me the suggestion, I will try it
Сделано хорошо.
thanks ❤️❤️❤️
A chave de acionamento provavelmente é nova.
you mean the switch
Отличная реставрационная работа. Вместе с тем всегда под рукой есть аккумуляторный каменный диск, но от неё летят искры. Спасибо за видео❤
many thank ❤️❤️❤️ have a nice day
@@hbrestoration спасибо за доброе пожелание. Взимно. Сейчас такое время, что время мастеров стоит дорого. Такая реставрация у меня займет примерно 12-18 часов. За это время на основной работе зарабатываю в три раза больше, чем стоит такой инструмент. Я понимаю, что вы это делали для своей души. Для личного удовольствия. Это как самому помыть свою машину. Это как вместо ресторана, самому приготовить барбекю. Всех вам благ от такого же мастера как вы. У вас есть чувство любви, это очень прекрасно.
@@Vperedsmotryashii
You're great, thank you. Wishing you always be passionate about your work and complete it well
porque lo de la bateria? ,no encontrabas pilas originales? o no tenias cargador ? es una curiosidad nada mas.
One of the reasons is that batteries like this will have to come with a charger that uses a different voltage in our country. If you need to charge it, you will need an additional power adapter for it, which is quite troublesome. The simple solution is to use a charger adapter that uses a common power source
Az elem miatt volt kidobva. LiIon akku sokkal jobban birja mint a NiCd
Người việt nam phục hồi cũng giỏi đó he.nhưng cảm giác hoi yếu tí
thank youuu ^^
TH-cam! STOP FREEZING MY 4k STREAM! I have 500Mbit download speed.
You can change the video quality in settings
@@hbrestoration That's not the point, I have 1 GB internet service and youtube freezes all the time. Even at QHD and 1080p at times.
You should limit your viewing device to 720p 🥹
@@hbrestoration With 1 GB per second download speeds, I can download an entire blu-ray movie in under 30 seconds. Streaming 4K should be a breeze, sorry , you don't seem to understand internet speeds.
@@freedomearthmoon1 yep, sorry I read it wrong. Your internet speed is terrible, can almost do everything with that speed
nice job 😎
🥰🥰🥰 thanks
@@hbrestoration most welcome😎😎
@@ROADKILL4147 🥰
Sensacional amigo.
❤️❤️❤️
I managed to translate that without looking, one hundred percent correct and I don’t know much Spanish , i am guessing it was a left out in the rain and forgotten. . All the best from England.
Beautiful restoration
Thank you ^^
Якби то Я розбирав, то розламав би, і корпус, і двигун, і кнопку, нічого б не вижило
I think it's not that bad 😅
Awesome job restoring that rebar cutter ! 👍👍
🥰🥰🥰 Thank you
Двигатель мёртвый 😢. После прочистки и сборки слышно как он клинит...
Yepp, there's still a noise because it's too rusty, I should replace it with a new one
Cắt được sắt phi 12😂
😅
It is one of the best restorations I have ever encountered on TH-cam Channel.
It is so amazingly done with the original parts of this little tool.
I have just subscribed to your channel; I am seeing your channel for the first time, and I can tell you that you're full of originality.
Thank you so very much for a restoration well done.
❤
I'm so happy to read your comment, it gives me a lot of motivation to make the video. Thank you very much
As good as new excellent job
🥰🥰🥰 Many thank
Wow
thank you❤️❤️😂
you went from 6 batteries to 3 ??
nice restoration though
The battery case only fits 3 cells
@@hbrestoration you should put them vertically
@@krozdo5an809 I've tried, but I can't do it. I also want to insert 6 cells
Perfeito 🇧🇷
many thanks
Terrific!
What happened?
Et si le moteur avait été grillé ?
I will re-wrap it or replace it. I chose to replace it because it was quite cheap
Great restoration!
Many Thank ^^🥰
Bạn làm thật tốt.Cho mình hỏi lọ nano lau cho bóng nhựa đấy là gì đc không
đó là một loại hoá chất phục hồi nhựa
Estaría bueno que expliques que productos utilizas. Muy buen video.
🥰🥰 many thank
Kompliment gute Arbeit
🥰🥰🥰 many thank
Excellent, superb work, very educational and neat restoration 👍👍👍
Thank you ^^
🥃👏👍🥃👏👍🥃👏👍🥃👏👍🥃👏👍🥃👏👍🥃👏👍
Another quality Chinesium product!👏 🎉😊
❤️❤️❤️ thanks
THINK I'M CALLING BULLSHIT ON FIXING THAT MOTOR!!!
😅
Well I was thinking "None of that looks too bad." Then you opened up the motor section.
thank you for cmt ❤️❤️❤️ have a nice day
21:20 где третий круглый магнит?
There are only 2 magnets
🥰🥰🥰
Nice😊
🥰🥰🥰🥰❤️❤️❤️
Great video what is price of Nano coating bottle at 09:45
only 2$☺
Restaurado cortador de vergalhão sem fio 🔌🚫😉
thank you ^^
2:06 wieso drei mal schlagen
einmal schlagen und gleichzeitig drehen
4:48 immer drei mal schlagen
These tight screws must be tapped many times
a great job
❤️❤️🥰🥰
Many thank❤️
Show!
🥰🥰🥰
Ха. Вспомнилось. Как американский разведыватльный самолëт, сбили, потом разобрали. А хозяев послали НАХУЙ.)
🥲
Этот инструмент забыт за правду, восстановление его доказало.😊
🥰🥰🥰
Резак арматурный, но автор видео в конце решил разрезать сраный 4-го класса прочности болт! Ну зачем же так?
The truth is that at that time I looked around and only found that bolt which was the biggest
Primero
❤️❤️❤️
As soon as the chrome spray paint comes out 👎🏻
It's not that it's leaking, it's the oil
Agree
🤦♂️
👏👏👏👏👏👏💯💯💯💯👍👌🇧🇷🇧🇷
❤️❤️❤️❤️
sloppiest restoration i ever saw
🥲
Too slow because you cut battery power in half it seems like if I had to use this one I would just use my muscles and a hammer and get more done sorry but at least you made it work
thank you for cmt
Get your vice anchored.
🥰 yep, thank you
Оно того не стоило.
🥲
Beautiful restoration, but please use gloves and a mask for your health !
thank you 🥰🥰🥰
Судя по началу, это ролик об утилизации. в конце алюминиевые части бросят в печку, обмотку двигателя в цветмет приемку. как из случайно подобранного получить стакан и закуску.
I will try to do better in the next videos :(
@@hbrestoration это шутка! ролик вполне интересный.
@@dmitriypolynin7273 I know I need to improve a lot, I hope you still watch and support me
Great work, but it would been so much better with a commentary..
I will try to do better
Ну и какая это реставрация? Просто глубокая очистка! А из деталей новые, только два подшипника и один болт...
I will try to do better in the next videos :(
Не дай вам Бог попасть на ТАКОГО "реставратора"!! Любой, кто знаком со слесарным делом, будет в ужасе от той дичи, что творит этот чел!! Так как он относится к механизму -- ЭТО ПРЕСТУПЛЕНИЕ!!!
what happened to you???🙃
@@hbrestoration разве это со мной случилось?? Это ж не я такую дичь творю! кто его вообще пустил к слесарному делу??
Le batterie al Ni/Cd sono più potenti delle Litio e tre batterie sono per pochi minuti di lavoro.
Not sure if they are more powerful, but they charge faster. It may take a few batteries
Ножовка по металлу .......!
what do you mean?
Тут был злой комментарий полный критики, но я решил его удалить. Единственное не могу молчать о переделке акума, скажу просто - ты потерял в мощности.
I used google translate and didn't fully understand what you said but it seemed like a bad experience. I will try to do better in the next videos
@@hbrestoration he spoke about battery, that you lost big part of power when replace battery units
🥲