KTM Duke 890r - Noisy engine fix! Tensioner issues resolved - Dirt Tricks instructions.

[@gilbertoalvarez29]

I love how Ktm transforms lots of people into a mechanic ❤brilliant

[@waltermessina5462]

It's true , unfortunately .... 😢🧡🧡🧡

[@zcryptxzz]

This was very informative, really appreciate you sharing this. My 2022 model is nice and quiet now. 👍

[@martinbrown9930]

Good video, and answered my question about needing to set the motor at TDC before changing the tensioner, some have commented on forums you need to, others not, so some confusion exists.
Mines not so noisy, but something to bear in mind for the future I feel.

[@viktorszabo7931]

Yes you should!

[@ajimenezamt]

Good info.BTW,Yoshimura will replace a revised mid pipe with a heel guard at no charge.I contacted them and replaced with no hassle.

[@vijayam1]

This is hydro-mechanical cam chain tensioner. The oil pressure is what loads up the piston inside the CCT and then maintains the pressure thereby making it maintenance free, basically like hydraulic tappet.

[@Dillonpickle]

Awesome thanks. Ordering now

[@nathanmiller5209]

i did this on my 2023 norden 901, got the tensioner from Rottweiler in California, ordered on a Monday it was in the bike on the Thursday afternoon, Im in the UK so was impressive. Just took old one out and put new one in as here, silent now.

[@paultaylorduke]

When you installed your's did you set your engine to TDC? I just ordered one from Rottweiler, so want to make sure i get full instruction before installing. Thx

[@nathanmiller5209]

i did the same as this video, no setting of timing,
@@paultaylorduke

[@Perfecttechs]

I didn't set it to TDC either @@paultaylorduke

[@icey5582]

@@paultaylorduke have u installed it on the bike, if so, how’s it holding up? I’d like to do this too but I use my bike as a daily commuter so don’t wanna risk anything 😂

[@paultaylorduke]

@@icey5582 yes, quick install and no issues.

[@simonemito90]

Hi great video..where can I buy that tensioner?? Thank you

[@theninja9896]

hi, could you send me the link where you can buy this component? Thank you

[@oargaoarga6018]

Any feedback about the KTM Duke 890 timing chain tensioner? is it worth it?

[@Turopites]

where you can buy this ?

[@PaoloCruz-o2m]

before removing the cam chain tensioner do you need to put it on TDC? thanks

[@prrsnikety]

Awesome, do more 890R vids as you run into them. My 890 Just went into the shop with a Pulser Coil, a radiator thermostat, and ignition cover gasket, problem, that all started with my battery dying. (according to ktm anyway) They're charging 6 hours of labor for it, which comes out to be about 260USD in labor.

[@TheMuseCoffeeco]

How did this last??????

[@TanqRStylE]

Hey Bryan,
was the noisy sound only at cold starts or does it even sound like this when its warmed up?

[@frankpusch4616]

Dirttricks chain tensioner

[@simonmcmaster8949]

How's the bike now, a good 9months since you posted the video, have you encountered any other issues, and how many Mike's have you done since you changed it.

[@swisscheese714]

I second this.
Would like to hear how this is holding up.
Tractor sounds galore right now 😁

[@jamessheppard990]

Interesting -- usually with CCT you need to rotate the engine to TDC before removing the tensioners...

[@sadeqalbana]

how can you tell that the piston is at TDC?

[@etruscanadv3296]

@@sadeqalbana There is a screw on the right side of the engine at the level of the oil window. You have to rotate counter-clockwise the engine manually until you see a notch.

[@viktorszabo7931]

Yes exactly

[@thatcammed3v880]

Is there a way I can send you a video of my 890? See if this is what I need

[@Mr.Winston]

Some people are saying you should have only done this at TDC but... ask yourself why.. does the engine only start up on TDC? This is a manual cam chain tensioner so I don't see a problem doing it like you did.. plus the fact we literally just watched you do it and it was fine

[@danwood4750]

If the hydraulic tensioner isnt doing the job its likely down to low oil pressure. Changing the tensioner is a short term fix, and I suspect the low oil pressure will cause your cams to wear prematurely as is the case on thousands of these bikes.

[@huugie025]

Not correct in all cases. Since it's hydraulic and designed to work well in operating temperatures, you first need to build the correct oil pressure which is not reached at a cold start. I read that the optimal pressure is at 6000rpm. My 890R is also noisy untill warm, or untill it reached somewhere around that rpm

[@bikenavbm1229]

why is that KTM and other manufactures are unable to make simple mechanical devices reliable that have been engineered for very many years and fit them to their machines, this is not cutting edge technology, KTM make very dynamic bikes no argument but their basic engineering choices sometimes really make me scratch my head WTF! also alas on occasion ride in aeroplanes in my bike kit whilst my bike rides on the back of a truck, just aint good enough for me anymore.

[@Misimi874]

is dangerous for the bike to ride with this sound?

[@xli64]

It depends, if the tensioner is too loose, it has a chance that the cam chain would slip 1-2 tooth while cold start, and damage values in combustion chamber.

[@MotoSjaak]

How is it holding up after the install?

[@Perfecttechs]

Several track days in and she sounds perfect.

[@17shinchan]

@Bryan Spears.. I may have lost it.. repeated the vid a couple of times.. where can i get the replacement tensioner?
Did he replace the whole tensioner and added a spring?

[@avrc9285]

its noisy cause its not electric 🤪

[@hollidick]

Wo kann man das kaufen?

[@frankpusch4616]

dirttricks kettenspanner