Sir, my uc 40 projector led bulb off after 1 hours, only audio work, and after 5-10 minute led display on but Again 5 minute display off what is reason please reply sir
U dont understand if u put a very bright led the picture will be washed out why do u thing with normal dlp or lcd projectors the higher the lumins the bigger and fatter the projector gets
For focusing light, it is very important to use a magnifying glass or two. Try one here: www.kaidomain.com/p/S020955.33_5mm-Optical-Glass-LED-Lamp-Lens-1pc
If u r going to use 10 watt to 30 watt LED with good heat sink then the LED stay cool because of excellent of ventilation design of Projector. But if u are going to use 50 watt to 100 watt led then u need big heatsink with fan which need to be fit in the Lamp compartment.
right but the side where the light shines is that cool to touch right . But the heatsink side is the hot side I know . But does the side where the light is outputing does it get hot ?
Hi. I know my reply is way but it might help someone still looking for solution. Find the set of wires (thin coloured wires) coming to mainboard from ballast (or power supply board integrated with ballast circuit) > then disconnect this set of wires from mainboard > then one by one, earth the connection (take a thin wire, attach one side to a screw on the mainboard and touch each coloured wire by the other end) and try to power it one. Good luck
Please explain connection with led driver with main board in detail and how to ignore 715w from power supply,you mentioned in this video
Sir will work for Panasonic PT-LC76E projector
Could you please tell me how many volts was the original lamp power board? You mentioned it rather quickly.
please, let me know correct cable pair in case of NEC LT260KP for lamp fooling.
bro I have epson EB 430. i tried but didn't worked. so can you guide. or make a good video for this one.
Sir, my uc 40 projector led bulb off after 1 hours, only audio work, and after 5-10 minute led display on but
Again 5 minute display off what is reason please reply sir
lamp and temperature indicator is still coming after bypass signal to board
Panasonic projector lamp and LED service line connection
Gracias men❤
why is everyone using weak leds? Surely a 100w led chip would work miles better.
They're pussies. 100watts led consume more amps.
Ryuuken24 it's only like 3-4 if you're running it at 30v it's not that hard to find a PSU that can supply the power
Exactly!
100W led does not work either. Because the light angle is wrong.
U dont understand if u put a very bright led the picture will be washed out why do u thing with normal dlp or lcd projectors the higher the lumins the bigger and fatter the projector gets
very well done!
why not use the bracket the old bulb was in?
hello sir kya ap mere projector ka lamp change karne mea mer help karge pls apke jo bhi charges hai wo mea pay kar duga ( pls help me )
For focusing light, it is very important to use a magnifying glass or two. Try one here: www.kaidomain.com/p/S020955.33_5mm-Optical-Glass-LED-Lamp-Lens-1pc
does thelight side stay cool ?
If u r going to use 10 watt to 30 watt LED with good heat sink then the LED stay cool because of excellent of ventilation design of Projector. But if u are going to use 50 watt to 100 watt led then u need big heatsink with fan which need to be fit in the Lamp compartment.
right but the side where the light shines is that cool to touch right . But the heatsink side is the hot side I know . But does the side where the light is outputing does it get hot ?
yes its get hot, but not to worry bcoz the window glass is too thick from where the light is reflecting inside the led. So, go on.....:)
hello aniket please make 100w 7000lm video soon.. as your bro teared all the parts of sony projector
How bypass lamp detector on mainnoard
Hi. I know my reply is way but it might help someone still looking for solution. Find the set of wires (thin coloured wires) coming to mainboard from ballast (or power supply board integrated with ballast circuit) > then disconnect this set of wires from mainboard > then one by one, earth the connection (take a thin wire, attach one side to a screw on the mainboard and touch each coloured wire by the other end) and try to power it one. Good luck
👍