Поставить головку в два раза больше , гениально Поставить головку в два раза меньше это превосходно Открутить маленькими(совсем) толчками отбойным отвёрткой превосходно шедеврально
@@loktar3 Если ты присмотришься к самому началу видео, он уже сорвал грани, выставил на гайковерт самый мощный режим и свернул их (с дуру можно и х** сломать), хотя гайковертом так слизать грани - это надо уметь я первый раз такое вижу. Я импактом откручивал TORX винты у которых до этого практически полностью слизал грани, зацепа оставалось процентов 10 на самой глубине, 3 щелчка и с легкостью открутило.
Если его не взял ключ, то долго отвёртки сломается. Чтобы открутить надо сильно ударить по шляпке,сантехническим ключом или приварить сваркой гайку сверху
В этом случае чтобы открутить, нужно знать ицифры и думать логически. Если ключ на 10 маленький, а 12 большой, хм, надо взять и испортить болт вместо того чтобы взять ключ ина 11.
Если начнёшь что-то приваривать к шляпке болта то он скорее открутится из-за нагрева. Сам постоянно сталкиваюсь с прикипевшими болтами и никакие брызгалки под типу ВД40 или ВД60, жидкий ключ в жизнь не помогут. Только горелка и только сильный нагрев спасает.
если болт закис, то резаная головка лопнет, оставив тело болта в отверстии. Если же болт в принципе крутится, но грани слизаны - трубный ключ или спец головка.
Always tighten it a bit first to break the rust seal and it will spin out easy. Use the correct size socket, don’t use wrenches including adjustable wrenches or channel locks.
Love my impact tool. Saved me beaucoup headaches. Only problem is despite using it for yrs i always 4get which way to turn it for which direction I'm trying to go w it!
Pregunto..no probaste con la medida de tubo que lleva de acá se nota que es 16 la medida y probaste con un 17 que lo Rompio y el 15 que no entra pero ese plano yo lo tengo va como loco una masa la demostración saludos mi hermano la mejor
Impact driver is not going to do that unless that bolt is less than 30 -40 ft/lbs the bit will twist and distort or break. But it's a great video on how an impact driver works... just not for that job
Impact can definitely get this done. Most impacts can handle 90+ish lbs. unless you are using a cheap maker. Even most house brands will have no issue upwards of 80lbs. This guy using the wrong size socket and a chrome one at that
I've actually used one of these and they work pretty well if you're working on it and you pretty much need one but the pipe wrench was a pretty funding joke
Some heat, some penetrating lubricant and a single hex impact socket on a bar is more than enough. If it is stripped on the hex faces possibly a cold chisel applied at a tangent will work.
A lazy workman quarrels with his tools.. if you don't want to apply your brains... Every tool will be useless.. that show how unskilled this Man is.. 😂
So much easier to just use the right size socket so you don’t strip the bolt in the first place
Exactly
and some wd40 wouldn't hurt
Or have an excuse to pull out your new toy
Poor workmanship leads to headaches for the professional
It's a demonstration. FFS. Durr.
Поставить головку в два раза больше , гениально
Поставить головку в два раза меньше это превосходно
Открутить маленькими(совсем) толчками отбойным отвёрткой превосходно шедеврально
Актёр без оскара.
Ну бл, бывает что так срезает и головка по размеру либо ключом, а способ действенный если место есть подлезть
@@loktar3 Если ты присмотришься к самому началу видео, он уже сорвал грани, выставил на гайковерт самый мощный режим и свернул их (с дуру можно и х** сломать), хотя гайковертом так слизать грани - это надо уметь я первый раз такое вижу. Я импактом откручивал TORX винты у которых до этого практически полностью слизал грани, зацепа оставалось процентов 10 на самой глубине, 3 щелчка и с легкостью открутило.
А вначале стукнуть молотком по нему не судьба, также можно подточить противоположенные грани под рожковый ключ поменьше.
цель то в другом, продать надо как можно больше ударных отверток
а если изначально взять головку нужного диаметра?
да даже тем же книпекс коброй можно было спокойно открутить.
Просто реклама типо вот смотрите какая офигенная штука 🤣🤣🤣🤣
Сразу видно вопрос дилетанта. Ударной отверткой такой и крест в потай откручивали, не то что болты.
Или хотя-бы крутить против часовой с самого начала
Тогда видео не получится.
I'm sure that 17mm socket would have worked if it wasn't upside down
Кто-нибудь, отберите у них инструменты и спрячьте
Согласен! Гайковерт не смог открутить то что потом открутила ударная отвертка. Ну это пиздец!))
Есть такое
@@anatolyromanishen5832 да он просто головку на миллиметр больше взял и слизал грани
@@anatolyromanishen5832
@@anatolyromanishen5832 Если грани слизаны,то ничего удивительного.
А ты не пробовал брать "головку" соответствующую размеру болта? 🤣🤣🤣
Já usei esta chave de fenda de impacto para tirar fora a porta do Fusca. Fenomenal! 😊
Может стоило насадку найти по размеру?)
Just use the right tool for the job from the beginning and ya won't waste time.
Right…
Hello
Use the right size
Muat be difficult.. look at the corner of the screw...he made to be not be openes by wrench even kn the right size
For me this reel will comes under a category of: Satisfying video ☺️💞
Quick somebody call Funk FPV I've found another video for him to react to 🤣🤣🤣
Lol I was about to say that😂
Funks coming for you haha
For sure
Если его не взял ключ, то долго отвёртки сломается. Чтобы открутить надо сильно ударить по шляпке,сантехническим ключом или приварить сваркой гайку сверху
В этом случае чтобы открутить, нужно знать ицифры и думать логически. Если ключ на 10 маленький, а 12 большой, хм, надо взять и испортить болт вместо того чтобы взять ключ ина 11.
Если начнёшь что-то приваривать к шляпке болта то он скорее открутится из-за нагрева. Сам постоянно сталкиваюсь с прикипевшими болтами и никакие брызгалки под типу ВД40 или ВД60, жидкий ключ в жизнь не помогут. Только горелка и только сильный нагрев спасает.
this is garbage, you need to hit the bolt head with a hammer, then turn it with a plumbing wrench or weld a nut by welding
@@Andrey_Prozrachniy не везде применимо.
Эксцентриковые ключи ещё в 70ых появились как раз для таких случаев
I can assume from your vast tool set and hand cleanliness, you cook your food from scrap wood found on the job site.
Можно раскошелиться и купить головки для сорванных граней.
Ещё и правнукам останутся, так как используются крайне редко.
Есть у меня такая отвертка. Только я болт срезаю, рассвердиваю и выкручиваю обратнонаправленным сверлом. Удобнее и быстрее
Если Гансом не открутил, то отвёрткой точно не открутишь
у него давление убавлено.
а так вдшка в помощь.
Где-то в обморок упал доктор дью 😄
Ah yes , my boy funk is gonna make a video out of this.
Есть специальные головки для сорваных граней
Баба крутила крутила - не выкрутила, дед крутил - крутил, не выкрутил, мышка прибежала, хвостиком махнула...
let's see what our comment section geniuses said about this
Just use your long nail you have 💅🏽
The heat releases it also🤣🤣
Да он и не бы затянут,резьба как новая! Попробуй ржавый открутить этой пукалкой,и ещё для ударного гайковерта нужны специальные ударные головки.
Это ударная отвёртка, а не гайковёрт и к ней в комплекте и должны идти биты.
@@user-sl4sb3fg2x ты тупишь что ли?Я имел ввиду то что вначале видео он крутил гайковёртом с обычной головкой
Ну или хотя-бы головка по размеру.
если болт закис, то резаная головка лопнет, оставив тело болта в отверстии.
Если же болт в принципе крутится, но грани слизаны - трубный ключ или спец головка.
pipe wrench be like:was that a joke 😂
Always tighten it a bit first to break the rust seal and it will spin out easy. Use the correct size socket, don’t use wrenches including adjustable wrenches or channel locks.
why not adj wrenches? I’m do maintenance at industrial mills and use mine to little complaint often
Use correct size 6 point impact or chrome v. socket
The bolt was already broken loose, ain't no way some slappy spinny screwdriver is breaking loose a 1/2in bolt that properly rusted.
@@nickmonty2961 p l
Yes we all have a saw grinder laying at home.
Aap mere Hussain ko mante ho
@@Allah_ka_Banda72 Yes Hazart Hussain R.A
Ну не знаю,у нас у это не такая уж и редкость.россия
I mean, do you not? Why don't you?
What da'fuq is a saw grinder?
A proper sized socket or ring spanner would have opened it without a fuss, without damaging the bolt.
Я удивлен,как он умудрился не открутить болт газовым ключём,
Просто он очень сильно старался НЕ открутить - ему контент надо нарубить, а не болт выкрутить. 🤷♂️
По мне проскальзывал бы
Bruh we don't use the ship bolts in home💀
I love watching these kids discover a tool I had 75 years ago
You’re in your 90s?
That’s all fine and good when you have all that space to work with.
Love my impact tool. Saved me beaucoup headaches. Only problem is despite using it for yrs i always 4get which way to turn it for which direction I'm trying to go w it!
Allow me to help......
To tighten a bolt or screw turn it:
Clockwise in the US
Counter-clockwise in Europe
Если бы заранее болгаркой углы не сточил, открутились бы ключом
The music got me pumped.
Вот это открытие!! Вау!!!! Аж целую ударную отвёртку показали...
to bro aap cut karna ka baad normal screw driver sa open hojata😂😂
The threads on that bolt don't look rusty 🤣
Полез я в карман,и...,достал эту отвёртку,а потом УШМ машинку(болгарку),вообщем победил я этот болт👍
This tool has been around forever!
you used the wrong sized sockets to begin with divy
I’m sure he knew that , the video is about demonstrating the tool he used .
всё гораздо проще. прежде чем откручивать болт стукни пару раз ему по голове достаточно сильно и потом спокойно откручивай.
Vice grips always takes those bolts off. I did it a million times
Bhai 1 litre m to start bi na hotti hogi😂
Pregunto..no probaste con la medida de tubo que lleva de acá se nota que es 16 la medida y probaste con un 17 que lo Rompio y el 15 que no entra pero ese plano yo lo tengo va como loco una masa la demostración saludos mi hermano la mejor
It's broken in the jam, so how can I get it
Surprised the bolt screw actualy in good condition
Wrench🔧 be like:- To hm kisliye baithe hai be 😁
El tornillo se suelta por los.impactis internos entre los hilos de las roscas.
I love the failed attempt in the background
Stripped bolts happen. Even with proper socket size. D Bag.. an impact driver is an underrated but powerful tool.
I was just thinking what is he doing 😂
Do these work ?
Ну ударная отвертка хороший инструмент . а откручивать дрери на стареньких Жигули без нее почти не как .
Да, да конечно! Если головкой болт слизали, то отвёртка поможет, ага))) особенно в пропиле. Совсем за идиотов держат)
Well u have to use the socket the right way first
Есть специальные головки для откручивания слизаных болтов)))
I bought one of those impact drivers.....60 bucks, I used it once.
Name of this tool
You haven’t used the right size socket, misleading reels
From where i can get this ?
If striped. Just get the next size down,hammer it on and then loosen. (Using an impact socket)
You can clearly see new markings after grinder and before unscrewing the bolt.
They loosen it up beforehand LOL
Not even the same bolt ..look at the rust below
Impact driver is not going to do that unless that bolt is less than 30 -40 ft/lbs the bit will twist and distort or break. But it's a great video on how an impact driver works... just not for that job
Impact can definitely get this done. Most impacts can handle 90+ish lbs. unless you are using a cheap maker. Even most house brands will have no issue upwards of 80lbs. This guy using the wrong size socket and a chrome one at that
That adjustable wrench you had first would have done it if you weren't holding it with your finger tips
I've actually used one of these and they work pretty well if you're working on it and you pretty much need one but the pipe wrench was a pretty funding joke
So much easier to not run the socket clockwise when youre trying to loosen a bolt...
Now find the same bolt😂
첨 복스알을 12각이 아닌 6각을 사용해야지 그래야 마모가 안되고 풀리지
На заводе у нас такого не бы и не будет. Такие вещи начальство домой себе заберает, а мы как можем так и выкручиваемся
I have a great tool idea for the guy in this video: fingernail clippers😂
No PB Blaster? Where is the correct size socket?
this tool name is impact driver
I was looking for that one guy in the corner to tell me how he is doing it wrong.
How about just using an impact socket? Chrome plated sockets arent meant for torque. Some rust inhibitor also.
Just get the “Gator Grip” socket!😆
Some wd40 first with the right size socket or wrench genius
Yep that's how that tool works had one 30 years ago wish I can find it👍🏼🤠
No one gonna talk about how he had it on “tighten” mode for the first one????
This is the proof when humans makes it more complicated 😂😂
wd-40 gets it done
What is name of this tool??
А головку по размеру не вариант взять ?
Now you gotta get a new bolt and had to buy a fancy tool, but couldn’t gotten the right socket for the job
Went from lets take out this Bolt to lets take out this screw pretty fast
Price
Some heat, some penetrating lubricant and a single hex impact socket on a bar is more than enough. If it is stripped on the hex faces possibly a cold chisel applied at a tangent will work.
I wish they would show these tools on oil drain plugs that sometimes do strip with the right size socket.
I'm pretty sure everyone is having a grinder at home
Jeez best tools
Ever
Heat up with torch hit with compressed air get out of way comes out like a bullet!
They do make sockets just for that exact thing ya know.
Right tool for the right job.
Не работает ударная отвертка на таких диаметрах. Ломаются грани. Пробовал я так делать.
A lazy workman quarrels with his tools.. if you don't want to apply your brains... Every tool will be useless.. that show how unskilled this Man is.. 😂
Теперь бы мне покупать какую-то китайскую хре** вместо того чтобы побрызгать WD-шки или в крайнем случае нагреть
インパクトでしめてるように見える
ハンマードライバー👍😃🇯🇵