TAO 110cc ATV engine swap. This 4 wheeler had low low compression so we put a brand new engine in it
ฝัง
- เผยแพร่เมื่อ 5 ก.ย. 2024
- This little 110cc is dangerously fast for it's size. The engine comes with absolutely no instructions. I oiled it up with Amsoil 10w30 small engine oil. We put slime in three of the tires to get it to hold air. We also take a close look at the carburetor.
Amazon like to an engine like this:
amzn.to/3p5RjUi
![🎤 ไปกันต่อออ! จับฉลากร้องเพลง x P’ #XXSIVK [EP.2] (1/2) เพลงของใครจึ้งสุดน้าา 💓🎤 #MXFRUIT](http://i.ytimg.com/vi/mLI_K0sAS4o/mqdefault.jpg)
I bet your grandson is tickled to have his 4 wheeler back! Proud grandpa! You have inspired me to buy a 1971 mercury 7.5 hp outboard. It had no spark, good compression not getting gas, has sat for years. I replaced points and wires from point block to coil. Now have spark! Fun. But took me hours as a rocky with outboards. Will work on the gas situation soon as I get a chance. 😃
keep up the good work, I'm confident you will get there.
Nice thing to do for the grandson! Try to do the same for my 7 grandsons, that’s really great, your grandson is very blessed to have you around, enjoy your channel!
Nice new heart for the kiddo right on she runs like a top
I know this is very late but it fits you like a glove!!
It does, but I guess I will give it back to the grandkid
The carb looked like it had rusty water in it, that can also cause problems trying to rev it up. That tank needed draining. Where I live if you leave a tank half full, over the winter water accumulates, they recommend before storing to always fill the tank to keep humid air out that causes water.
I’m doing the same thing with my 110cc Tao Tao, but I’m doing an engine swap too. I’m putting a 4 stroke 125cc 4 speed on it. Well see how that goes. I’ve had the thing since I’ve been 5 and I’m now 16 so I thought I should put a bigger engine on it.
That will make it hall butt for sure.
Did it fit?
Nice video. Love the channel!
Much appreciated!
@@Michaelsbackyardmarina no problem. Check my channel out and sub if you like it. Newer videos are better, just got a new gopro
The valves were probably tight on the old engine. Happens all the time on these. Couldve fixed it for free
possibly
Definitely
that thing seems like it was geared quite high and still accelerated good 👍. although I gotta say that old engine wasn't running bad because of bad compression. that was 100% a fuel issue. also seeing as to how clean the engine looked... what might of happened is you may have used a compression tester with a one way valve at the gauge side instead of the spark plug threads side. long story short the dramatically lowers the compression and all cheap compression testers are built that way
Wrong on the compression tester. I have three and they are work well and the same, you can't put it together wrong on the ones I have. Thanks for watching
@@Michaelsbackyardmarina I didn't mean you put it together wrong though. They come from factory like that
Did you say "Spacely Sproket"! I love it.
I did, wondered how many people would pick up on the Jetsons reference
That thing sounds like 5 o'clock charlie!
Those motors will run forever the low compression was more than likely just a quick valve adjustment
she was smoking like a two stroke.
@@Michaelsbackyardmarina was the cylinder wall damaged? If not it was probably just a bad piston ring, also you could have bought a new cylinder for it for like half the price
i would of put in 15w40 rotella t4 oil for breaking in the engine
ok. much too late for that now. Has lot's of hours on it now.
Here is a challenge for you why not rebuild the engine for the 110cc motor you never know what it will come handy for in the future. I reckon it is only piston rings or something less complicated and I am sure with your knowledge you can do it.
Hilarious to watch you doing donuts...lol!!!
Hey what can I say....I like to have fun
waiting to see more progress on your tri hull
RMD Creations coming in about a week...,
4 strokes and 2 strokes are entirely different beasties, I think you fixed the ATV by cleaning the rusty water out of the fuel system. Usually if a 4 stroke runs smooth at idle, it will run smooth at high speed regardless of what the compression is.
true
infact if it runs at idle it will have even less trouble running at high speed because the faster the piston is moving the less time air has to leak out
How did you connect the old wires to the new wire on the new engine. There is a white and yellow wire on the old engine and two yellow wires on the new engine. Is there a certain way or should I just put them together?
he did a stator swap from old to new engine
correct
correct
Hi from Ohio. Do you go by Mike, Mich or Michael? Love your videos. My grand sons would love this. I think it is pronounce "cheap import crap, but that's not all bad. I also sent you a msg how to see pics of your Glasspar.
I agree with your translation, how did you message me? I haven't seen it yet. My home page has my email address.
@@Michaelsbackyardmarina I just sent to your email now.
I would guess it has a broken valve spring.
It may have been. I haven't pulled that motor down.
So my question would be. Do you know the bolt size for bolts that go through the frame and into the bottom of the motor.
sorry I do not.
Is it possible to replace my son's 60cc with the 110cc on the same frame?
I have no idea, thanks for watching
I have the same ATV. I just bought an engine as well. Does it matter what carburetor goes on it?
My bolting length seems to be a hair off. Was yours?
it's some cheap Chinese stuff, it may not always line up for sure.
How do I connect the life that goes on the side of the engine. It didn’t come with a connector. How did you do it?
Did you connect the two yellow wires, to the white and yellow wire? Thanks.
@@Michaelsbackyardmarina how do I connect the 2 yellow wires to the white and yellow wires on the new engine cover?
I have almost the same quad . Compression is around 70 psi (not good obviously) the quad has F N R but the new motor has no shiftable gears (just forward) is there a way to combine the new engine and keep the shifter or would it be a fowward only quad ?
I have no idea about that. Thanks for watching
Ya you can get a 125cc 4 speed for alibaba for 130.
Good to know, thanks for commenting and watching.
Hello, thanks for the video. Where did you buy this engine? I need to do this same thing. Thank you.
I just added a link in the description or you can follow this link amzn.to/3p5RjUi
Try adjusting the valve lash
Wonder if a Honda motor will fit or 125 or 150 Chinese
good question. Not sure. Thanks for watching.
I have a tao tao 125cc very relaible like honda clone lasted 7 years it recentley developed a rod knock cause i beat the crap outta it put a police siren on it everything buy one for $800 100 precent worth it
Cool, thanks for watching
What exhaust was that?
I have no idea, thanks for watching
Hey man. About how long did it take start to finish?
Swap out about an hour
Could I ask where you bought your motor from?
amazon
WHERE DID YOU ORDER THE ENGINE I NEED ONE
Amazon
Is this engine realible?
vibrates like hell but still running. It's not a well balanced chinese motor