Just to add some a thing for DIY to make it easier - the fit of the sleeve inside the vanos body with the bearings and shims is loose enough to allow you just to undo the big 18mm nut on the vanos piston and leave the gear bolt that is reverse thread ... just tap the vanos piston on a clean table after you have the nut out and the sleeve will come out ... this way you can start grinding the sleeve and then check the fitment
In my car that vanos piston bearing has about same clearance but it doesn’t rattle at all, I guess it’s because of that springloaded washer upgrade, my car came upgraded from factory it’s -96 e39
Nice DIY guys. I did the Vanos washer upgrade and the Beisan anti-rattle kit ( Jan. 2011)on my M50B25 vert, make 10-'93, at 190k km's. But after 2 years I read on a BMW forum the Beisan o-rings is as bad as the BMW OEM ones. I can't tell because I'm now on only 213k km's, because I drive my vert only about 3000 km a year, hahahaha. Maybe the Amazon ones are a different better brand. BTW I tightened the washer nuts at 9 Nm instead of the recommended 10 Nm, because it would move even more smoothly( read it on a forum). After the washer upgrade and anti-rattle kit, I had a completely "new" car!! Dutch regards, Nico.
I have never used beisan o-ring , so can't tell . Actually the recommended torque spec is 8 nm to the reverse thread bolt . So in that rate after 20 years you will have +60k km above that ... nobody will believe you hah
@@crank3646 the reverse one yes. Sorry, but I ment the nuts on the 3 new struts. And yes I got the car in March 2004 at 136k km, and 17 years later it is on 213k km😅🤣🙈. First it was my daily. Regards Nico.
Silicone is best for rubber and plastic. I would suggest a moly grease for this. Also, I hope the cap nut was installed and torqued before checking for free play. I didn't see him say or do that. I would also suggest you follow all factor torque specs. They are not decided randomly. Increasing or decreasing this value will eventually cause regret.
Thanks for the video! It is by far one of the best vanos rebuild walkthroughs online! I am attempting to resolve a rattling issue on my s52. I was wondering if I should order the dr vanos kit or do it myself.
Do yo need to block the camchaft and flyweel? I watched a video about the double vanos from nathans diy and he said if you do not move any thing you dont...
Why do all the accented youtubers seem to be more knowledgeable? I came here trying to understand how vanos work and the assembly process makes it all clear.
My problem is rattling. I don't know if it's the vanos or not. But when It idles then rattles. Coming between the engine intake. Somewhere there. When I accelerate u can't hear it anymore.
Здравей да попитам след като съм с м54 всмукателен и м50 без ванос пак всмукателен вал lock-ването как става пак ли като при теб само единия или филма е друг? Благодаря предварително. Поздрави🎉
Благодаря за полезния клип! Чакам да ми дойдат уплътненията и го започвам! Има малко луфт, но не трака. Да го разглобявам ли да го шлайфам или може да сменя само уплътненията? Поздрави!
Поздрави за страхотния канал и полезните клипове ! Също така имам един въпрос, когато се повреди ваноса това води ли до ниско налягане на маслото и влошено мазане на разпределителните валове.
Мерси ! На теория да , ако изтърват о-пръстените би трябвало да намали налягането , но чесно казано не съм срещал такъв случай с единичен ванос . Обикновенно е при двойните ваноси . При ниско налягане на маслото всичко ще почне да се износва не само разп. валове .
Витоновия и тефлонов пръстен какви ползвахте? Че на пазара в момента има няколко (полски немски английски)? Ще ми се наложи и моя ванос да обслужа за това питам.
Just to add some a thing for DIY to make it easier -
the fit of the sleeve inside the vanos body with the bearings and shims is loose enough to allow you just to undo the big 18mm nut on the vanos piston and leave the gear bolt that is reverse thread ... just tap the vanos piston on a clean table after you have the nut out and the sleeve will come out ... this way you can start grinding the sleeve and then check the fitment
How do you prevent the cam from rotating did the timing go off timing in the intake cam shaft?
In my car that vanos piston bearing has about same clearance but it doesn’t rattle at all, I guess it’s because of that springloaded washer upgrade, my car came upgraded from factory it’s -96 e39
Nice DIY guys. I did the Vanos washer upgrade and the Beisan anti-rattle kit ( Jan. 2011)on my M50B25 vert, make 10-'93, at 190k km's. But after 2 years I read on a BMW forum the Beisan o-rings is as bad as the BMW OEM ones. I can't tell because I'm now on only 213k km's, because I drive my vert only about 3000 km a year, hahahaha. Maybe the Amazon ones are a different better brand.
BTW I tightened the washer nuts at 9 Nm instead of the recommended 10 Nm, because it would move even more smoothly( read it on a forum). After the washer upgrade and anti-rattle kit, I had a completely "new" car!! Dutch regards, Nico.
I have never used beisan o-ring , so can't tell . Actually the recommended torque spec is 8 nm to the reverse thread bolt .
So in that rate after 20 years you will have +60k km above that ... nobody will believe you hah
@@crank3646 the reverse one yes. Sorry, but I ment the nuts on the 3 new struts. And yes I got the car in March 2004 at 136k km, and 17 years later it is on 213k km😅🤣🙈. First it was my daily. Regards Nico.
@@crank3646 where did you get the o-rings from and what size they are? Thank you
Dimitar Dzhongozov link in description
@@kenbash6213 no link I'm description for the rings
Silicone is best for rubber and plastic. I would suggest a moly grease for this. Also, I hope the cap nut was installed and torqued before checking for free play. I didn't see him say or do that. I would also suggest you follow all factor torque specs. They are not decided randomly. Increasing or decreasing this value will eventually cause regret.
is it safe for engine to drive with broken vanos, even tho its making sounds?
Thanks for the video! It is by far one of the best vanos rebuild walkthroughs online! I am attempting to resolve a rattling issue on my s52. I was wondering if I should order the dr vanos kit or do it myself.
Thanks Daripalli !
Depends how patient you are with the sleeve , i guess :D
Where or whom did you get the Intake Gear replacement washers, spring, and longer bolts from
Do yo need to block the camchaft and flyweel? I watched a video about the double vanos from nathans diy and he said if you do not move any thing you dont...
Need help please. I cant tell if it's the vanos or something else. My disa valve was lose and broken. I fixed That but still noise coming.
Why do all the accented youtubers seem to be more knowledgeable? I came here trying to understand how vanos work and the assembly process makes it all clear.
My problem is rattling. I don't know if it's the vanos or not. But when It idles then rattles. Coming between the engine intake. Somewhere there. When I accelerate u can't hear it anymore.
Hi do you use flywheel lock pin?
Здравей да попитам след като съм с м54 всмукателен и м50 без ванос пак всмукателен вал lock-ването как става пак ли като при теб само единия или филма е друг? Благодаря предварително.
Поздрави🎉
Благодаря за полезния клип! Чакам да ми дойдат уплътненията и го започвам! Има малко луфт, но не трака. Да го разглобявам ли да го шлайфам или може да сменя само уплътненията?
Поздрави!
Is this only an issue for single Vanos M52s? Was it fixed for the double vanos M52TU?
Nope double Vanos has the same issue
thanks for the video
nice job as always
Thanks D G !
Поздрави за страхотния канал и полезните клипове ! Също така имам един въпрос, когато се повреди ваноса това води ли до ниско налягане на маслото и влошено мазане на разпределителните валове.
Мерси ! На теория да , ако изтърват о-пръстените би трябвало да намали налягането , но чесно казано не съм срещал такъв случай с единичен ванос . Обикновенно е при двойните ваноси . При ниско налягане на маслото всичко ще почне да се износва не само разп. валове .
Витоновия и тефлонов пръстен какви ползвахте? Че на пазара в момента има няколко (полски немски английски)? Ще ми се наложи и моя ванос да обслужа за това питам.
Или Beisan или от X8R от ebay ако не ти се чака от щатите
Good job!
I will do mine soon, is rattling but not as bad as yours so I can postpone few more weeks 😂👍
or years :D
a trick: watch series on kaldroStream. Me and my gf have been using it for watching all kinds of movies lately.
@Bennett Dylan Yea, I have been watching on flixzone} for months myself =)
👍😎
Пичове къде ви се намира сервиза ? :) Поздрави от фен!
PS: Намерих ви ;)
Намираме се в Бургас
Wow thats loud!!!
Защо не запали от първия път? Приятел има същия проблем с м50б25, мерси.
Защото бях спрял горивото към мотора
the sandpaper its P320 not 470 ;)
I was waiting , someone to notice it :D
Това е дизелов м50 :D майтап си права.
Аз ще вкарвам мойта че ми тракат хидравличните повдигачи та да видим кви змии и гущери ще излязат
Успех с начинанието :)