Hi There , I Need help creating this same Arm but controlled by a 3.2 TFT display . I want to have a simple menu system on the TFT , when you select a specific number the servos should rotate to that specific direction.
Sir, can you tell me how many servo motors and potentiometers you have used in this robotic arm record and play? Can you tell me about the robotic arm record and play, what power do you have used in this project? Please reply to my questions. Thank you, sir.
how i can change the recorded position speed ? means after one postion it take 3 second to repeat recorded position which value i have to change in the code. please reply
Sir, can I used the wooden robotic arm chassis instead of making a robotic arm chassis in the robotic arm record and play project? Please reply to my question. Thank you, sir.
bro I built the arm but I have a problem when uploading the code to the arduino nano board the servo motors stay without moving they move forward and the led only blinks what do I do
Bro only two moter are working and one potentiometer chatch fire and other than only two where working bro please help me out how to fix it and I have tested moter all where working properly please help help
it throws an error in orange and says that it may be that errors are produced when the code goes up the servos adopt a position and remain rigid and do not move
I think it is an error in the code because I tested the board with a routine for the arm and it works perfectly but when I upload the minirobot code, what was said above happens
Hello sir maximum motors kitni ho sakti hai nano par
20k or 10k potentiometer?
Which to use
Hi There , I Need help creating this same Arm but controlled by a 3.2 TFT display . I want to have a simple menu system on the TFT , when you select a specific number the servos should rotate to that specific direction.
10:59 what is this wire(Red and Black one), and where does its other ends connect to?
5v supply from external power supply
@@kitronix Thanks!
The servo are not rotating accurately and sometimes 2 servos are Responsing at once plz reply
Did you connected the potentiometer to the correct pin?
@@kitronix yeah I connected them well
I have same issue, aren't solved?, @rishik
@@adilshaa5222 no
What size capacitor did you use
16v 100uf capacitor
which type of servo motor did u use 180 degree or 360 degree
ආහ්...
Sir, can you tell me how many servo motors and potentiometers you have used in this robotic arm record and play? Can you tell me about the robotic arm record and play, what power do you have used in this project? Please reply to my questions. Thank you, sir.
I used 4 servos and pot
5v as input
To record position you need to press the button for recording per position and to play you need to 3click the button
Bro in this circuit what records the position the ardurino or the laptop cable which is plugged in ardurino
push button records the position
What type of capacitors and resistor are used ..?
How many volts resistor did u use 10k 1/2v resistor or 10k 2v resistor
10k 1/2 watts
@@kitronix thanks
Sir how many position can we record
bhai hum vo data cable hata nahi saktai hai kya
no we should plugin cable for ardunio
4 MAD BOYS bhai hindi mai batao na aap kya kahna chahte ho
hello sir what is the maximum number of motor connections on arduino
Bro, Size of resistor?
1/8 watts
@@kitronix thanks bro 👍
Keep making videos like this bro
Thanks 😊
in your diagram where did you connect 5v through capacitor?
to the gnd and 5v in ardunio
I have connected the pot and servo motor perfectly but the servos are not rotating accurately and the led light is blinking for 3 or 5 seconds
We car use 100k potentiomiter???
please reply
yeah you can use but the sensitive will be more
what are the last red and black wire for?
For power supply
Will it work with arduino r3
Yeah
how i can change the recorded position speed ?
means after one postion it take 3 second to repeat recorded position
which value i have to change in the code.
please reply
please reply me
I dont understand standard you question
this robotic arm repeat position again and again
but
it takes 3-4 second delay in each postion .
How i can reduce this delay
I am trying to build this, can you please help me
Sir please reply wich resistance are use in arm?
10k resistor
Can we supply the 5v Power with hw 9v battery
I have a question what voltage is needed to power the servos circuit is it 12 volts or 5 volts
5v
@@kitronix Thank you
Bro can I use 25v 100uf capisitor please reply ☺️☺️☺️☺️
Yeah you can use!!!
Awesome bro keep it up
Thanks bro
Which resistance use
How to attach capisitor in diagram it is not clear and external 5v power how to connect plz tell
Bro my teach and play back is not happining please give reaply please help thus the project I am doing
Bro please reaply me
It's argent🥺🥺🥺🥺
What's that yellow one...can u tell me the name of it...
Which one?
At which min?
Sir, can I used the wooden robotic arm chassis instead of making a robotic arm chassis in the robotic arm record and play project? Please reply to my question. Thank you, sir.
Yeah you can use wood but it needs to be weighless
For those who build this how much does it cost?
the 5v external power supply is Ac or Dc
Dc
Wow super bro❤️
❤️❤️
The servo motor is used 360 degree or 180
180 degree
Thank you so much
Thank you 😊😊😊😊😊😊💗💗💗💗💗
Can we give external 5v power with 9v battery
yeah
Do you have a social network to send you a photo of my connection because I connected the buttons
Check out the description for the circuit
Bro can we use A10k potentiometer please reply bro 🥺🥺🥺😊😊😊🥺🥺
Yeah you can use
Super bro!! Nice video
Thanks ❤️
Super da ❤️
thanks da
@@kitronix bro njan android app ill aanu compile cheythathu pakshe comiple aavunilla error kanikunnu .....what to do brother 😪
@@rootcyborg solved???
thouse were 10k resistors ?
Impressive
Thanks ❤️
bro I built the arm but I have a problem when uploading the code to the arduino nano board the servo motors stay without moving they move forward and the led only blinks what do I do
Check your connection with multimeter
Which resistor
Can we remove the arduino power wire from computer and power arduino using powerbank
yeah
Bro you belongs to which branch of engineering
😅 iam studying high school
@@kitronix ok bro and tnq for the reply
Can you make it wireless with bluetooth module? plz make it
in future i will try to make
Ok, I will wait for it.
Bro I use Arduino Uno for this project and I burn code to Arduino Uno but light is blinking on
Arduino please reply
Connect every thing and check
how can i do the programming? greetings from Argentina
Bro please help
When I upload your code ,it's saying low memory available, stability problems may occur and led is blinking please 🙏🙏🙏
It's normal only don't worry .
The code will work properly
hi .can you halp me plez ,I have project this year for your project 😢
please kind sir , can all the material names ?
Watch the full video
The resistor is how much ohm
Check out the circuit
What to do if I want to make it battery-operated?
Use 2x 3.7 cell
@@kitronix okay thank you so much!
🤗
Bro only two moter are working and one potentiometer chatch fire and other than only two where working bro please help me out how to fix it and I have tested moter all where working properly please help help
You need to connect all the potentiometer inorder to work
And Also check the connection onces again before supplying power so that you can avoid buring components
Ok bro ☺️
it throws an error in orange and says that it may be that errors are produced when the code goes up the servos adopt a position and remain rigid and do not move
But the code uploaded successfully??
If the servos adopt a position means code has been successfully uploaded. your connection may be wrong or you didn't connect the push buttons
@@kitronix yes
Can I use Arduino UNO instead of Arduino pro mini ??
S
tienes alguna red social para enviarte una foto de mi conexion porque yo conecte los botones
Can I use ardiuno Uno and please give me circuit of ardiuno Uno
Plz reply brother
Same as in nano
Thank you 💖💖💖
can you please tell me after uploding code into my arduino why it is not working the led is only blinking
twice in one second pls give me its solution
Did you connect the push buttons???
@@kitronix no
i actually tested with servos and potentiometers
You are indian 😊😊😊💗💗💗💗💗💕💕💕💕🥳🥳🥳🥳🥳🐱💕
I’m going to make an animatronic with This
Could you help me in the arduino code when I upload the code it says that it could cause instability problems and the board works perfectly
Does it throws up any error while uploading?
Or it says "done uploading" in left bottom corner
@@kitronix yes
Which material did you used for the arm?
And when will you upload the Arduino code and the schematic?
Btw great video, keep grinding!!!
I used 5mm foam board
Thanks bro
I will upload the circuit and code as soon as possible
@@kitronix can i use any other material or this is strong enough 🤔?
Ok bro no problem, I'll wait
🔥🤩 kitronix 🤩🔥
Make drill machine with 555 dc motor
Sure I will make
@@kitronix thanks
And how to connect the 5v with ardiuno
Use usb cable
Bro the 5v how to set it in uno
I can't understand
In ardiuno Uno the capisitor and 5v supply set in uno
While uploading code, i am getting LOW MEMORY errors
Code not uploaded?
@@kitronix nope, keep getting error occurred while uploading sketch
i deleted record codes ad fixed the low memory thing but i still get errors while uploading sketch
@@kitronix btw, do i need to have external 5v power supply? can't i just keep arduino plugged to my laptop?
@@ButterDragon you can use usb power bank
How to avoid the jerks while operating the robot
Bro, It really work ?
Yeah bro it will work
bro , please make more videos on your robotic arm
Sure bro
I think it is an error in the code because I tested the board with a routine for the arm and it works perfectly but when I upload the minirobot code, what was said above happens
Did you connected both push buttons to Arduino as shows in the circuit??
@@kitronix if one goes to pin d4 and the other goes to d5
Yes
And in circuit Diagram one mistake is that
5v input are not Connect to circut
check properly
you are right, the diagram has a mistake. 5v power supply only connected to the cap and servos, not connected to the circut.
@@WilliamCuriosityalso pot center pin is grounded,
Actually the Center pin is input
Bhai please help product list send Karna plz
Urgent h bhai
Bro i can use Arduino Uno
hello can you give me the code please i am stuck on that pls
bro I don't understand the diagram you made
Please show the circuit diagram
Can you please give me the code. Kindly?
allow me some social network to send it to you or your email pliss your project is very interesting really
Bro the drive link of code is not working can you give another link bro please ❤️❤️❤️❤️
drive.google.com/file/d/1BgE0YZ_FB2Wxs-yZ8MDj5JS2kPGRxDeM/view?usp=drivesdk
@@kitronix bro it showing
Preview is not available.please provide the code ❤️❤️❤️
You can only download
@@kitronix ok bro tnq for the reply
@@kitronix bro after download how to view code please help me bro😭😭😭😭😭
what happend to your handd
👍👍🥰🥰🥰🥰
Thanks
❤️❤️❤️
THANKS FOR YOU COMMENT
the code doesnt show
check the description
but it doesn't work
It doesn’t work. Can you please give me the word file?
Please give us code
I'll upload soon as possible
As possible
check the description
Plz reply
Can a gear motor replace a servomotor?