Nice video, thanks for taking the time Ron. very helpful even for the non-touch VBC. A Vbar Neo tuning video series with step by step instructions- showing symptoms of different issues and how to correct them- would be awesome. I can’t get my logo 550 to piro in one spot. It travels all over the place. I bought it used and will do a rebuild to spec but I’m wondering if that is a main rotor gain issue? I had this problem once in the past. The tail also has a slow wag but this was a poor build, I’ll see if it’s there after the rebuild. Any ideas on the piro issue? Pack CG seems perfect and this problem happens with different pack sizes and weights. Auto trim worked ok-ish for hover but the Heli wants to tip over on spool up. Thanks
@@laughingstill I use 2s LiPo, not sure whether it will burn with 8.4V, maybe worth to try. How many volts do you have pls? Many people say there need to be step down reg for BPS-1. I have Spektrum too, that one work fine.
@@laughingstill THANKS A LOT. I want to use telemetry, but I am using a V-Bar governor, do I need to use the Governor Scorpoion or not? (I have V-BAR CONTROL and V-BAR NEO, ESC - SCORPION)
@@laughingstill Thank you, I connected it today, but here's the problem: it shows 50 mAh, I haven't connected the engine yet. Could this be, or was it just that I set up the V-Bar Governor badly? Tell me, is it better to use Governor V-Bar or Scorpion?
![ออกพรรษาน้ำตาหล่น - แอน อรดี [OFFICIAL MV]](http://i.ytimg.com/vi/PFZtOcY9ONA/mqdefault.jpg)
That was extremely useful to help me setup my first nitro heli after many years, thank you!
Very informative, Ron!
Nice video, thanks for taking the time Ron. very helpful even for the non-touch VBC. A Vbar Neo tuning video series with step by step instructions- showing symptoms of different issues and how to correct them- would be awesome. I can’t get my logo 550 to piro in one spot. It travels all over the place. I bought it used and will do a rebuild to spec but I’m wondering if that is a main rotor gain issue? I had this problem once in the past. The tail also has a slow wag but this was a poor build, I’ll see if it’s there after the rebuild. Any ideas on the piro issue? Pack CG seems perfect and this problem happens with different pack sizes and weights. Auto trim worked ok-ish for hover but the Heli wants to tip over on spool up. Thanks
Futaba BPS-1 RPM Sensor Works with the V bar
Verry helpfull video🙏
Yes sir!!!
All needs to be connected
Can you do video for buying pro/rescue and installing for receiver .
I’ll try and do one soon
Yes, if it in a Non pumped OS motor. Have not confirmed with YS
Is there anyway i can get in contact with you to go through my touch.. got problems 🤦🏼♂️
Hi Ron, hope you are well. Do you use BPS-1 directly to VBAR or have you reduced voltage via step-down reg. pls?
Direct to the VBAR depending on your voltage going to the VBAR. LiFe is safe
@@laughingstill I use 2s LiPo, not sure whether it will burn with 8.4V, maybe worth to try. How many volts do you have pls? Many people say there need to be step down reg for BPS-1. I have Spektrum too, that one work fine.
BPS-1 is good on 2s
Wait, now that I think about it I did step the voltage down for that semsor
***Sensor
Waiting on my goods, So N556 do you set it as 550 or 600 in the set up thanks
Jim Penrose 550
Did you ever have a chance to make the follow up video going over PID and basic throttle? Can you put a link here or in the description please?
Hey ron. Is that my n5c I sold you
Listen, CH1-3 is clear, but why center CH4?
Not necessarily needed for some heli’s. If you have an older mechanical CCPM then you will need that as well
@@laughingstill THANKS A LOT. I want to use telemetry, but I am using a V-Bar governor, do I need to use the Governor Scorpoion or not? (I have V-BAR CONTROL and V-BAR NEO, ESC - SCORPION)
No, you can see the telemetry with the VBAR gov. You just need the cable that goes from the computer port on the esc to the telemetry port on the NEO
shop.mikadousa.com/05089-VBar-ControlScorpion-ESC-Cable-500mm_p_1774.html
@@laughingstill Thank you, I connected it today, but here's the problem: it shows 50 mAh, I haven't connected the engine yet. Could this be, or was it just that I set up the V-Bar Governor badly? Tell me, is it better to use Governor V-Bar or Scorpion?