Hey can someone please help me I been without a car for a month .. I have a 2009 Nissan Mureno and when I press the gas rpm goes to 3 but it won’t drive , when I disconnect the battery and reconnect it , it is able to move like for 2 seconds and then stops moving again until I disconnect and reconnect battery. Prior this my car was driving slow like not pass 20 or 30 mph . What could it be
@@MrtalentedReid the thing is I am not able to drive it to auto zone to get it checked . Also, my parking lights will not turn off so I had to disconnect the battery and that clears out the check engine light. Is the codes stores even if the check engine light is not on?
@nanaross3598 code should stored as pending or permanent Autel AL519 OBD2 Scanner, 2023 Newest Professional Mechanic OBDII & CAN Car Diagnostic Code Reader Tool for Check Engine Light, One-Click Smog Check, DTCs Lookup, Upgraded Ver. of AL319/ MS309 a.co/d/4YDeOfl
This could be very helpful to me because my car starts and runs great but at speeds between 30 and 45 mph, it gets crazy! It pulls back and pulls forward simultaneously! I thought it might be the TPS! Thank you! I'll check this out first!
Thanks for stopping by. So it could be a bad throttle body, bad pedal sensor, blown fuse bad pcm, bad relay. But you can try a different throttle body first and see. And after you replace the throttle body clear the code. If that doesn't fix the problem try a different pedal sensor and continue checking all those things I send you.
I have a 2006 Nissan Murano and it idles fine when in park but when I put it in gear the gas pedal doesn't respond. I've replaced gas pedal twice and it still doesn't solve the issue
I am having problems with my 2006 Nissan Murano, Changed Pedal, Changed Trottle body and still car won't accelerate. Once TPS or Pedal changed car drives for a while like 1km and it goes to limp mode with Slip light and VDC displaying a check engine light, when I disconnect the pedal cable the car get high acceleration can drive . But it's slow. please any suggestions for possible solutions?
Ok there are few things to change first check the speed sensors in the wheel second check the input and output Speed sensors on the transmission third check the abs brake module fourth check the steering angle sensor fifth check the wiring for and loose broken or slack connections of the wires sixth check fuses. So if all that I told you about Is in good shape maybe you have a defective computer or bad transmission
@@MrtalentedReid the car is able to move when I disconnect the pedal cable it goes to a high gear. So I don't know if the transmission can be bad and it still able to drive on its own when I disconnect the pedal cable and put the gear on drive D
There are a few reasons why your car might be struggling to accelerate. It could be due to a problem with the timing belt, the spark plugs, or the fuel injectors. It could also be because you have a dirty air filter or a clogged fuel filter. The fuel system may also be low on fuel.
09 Murano, the car starts fine and idles good drives good with good pic up from complete stop. But randomly after a few minutes it will rev slightly high the a couple seconds letter the power come back to normal. It's random
Can anyone help got Codes P1122 & P1126 Crank no start 2003 nissan murano,narrowed it down to either the pedal or the connector that plugs into the pedal does anyone know how to check the connector?
my murano 2003 drives beautiful but sometimes after a couple or 50 miles it won't accelerate normal it accelerates very slow and once I turn it off and restart it starts accelerating fine again 😢
I Thank You For Your Expertise Very Detailed Thank You AGAIN
You are very welcome
Did you remove any of the plastic on the car to access the pedal better ?
Only if you need additional space
How do you pull the connector off without damaging it? Does it have a pull tab on the side!
There is a lock clip that you need to squeeze and slide it off
The lock clip is broken
Hey can someone please help me I been without a car for a month .. I have a 2009 Nissan Mureno and when I press the gas rpm goes to 3 but it won’t drive , when I disconnect the battery and reconnect it , it is able to move like for 2 seconds and then stops moving again until I disconnect and reconnect battery. Prior this my car was driving slow like not pass 20 or 30 mph . What could it be
What code are you getting? You may need a new pedal sensor or a computer or it could be a broken wire somewhere
@@MrtalentedReid the thing is I am not able to drive it to auto zone to get it checked . Also, my parking lights will not turn off so I had to disconnect the battery and that clears out the check engine light. Is the codes stores even if the check engine light is not on?
@nanaross3598 code should stored as pending or permanent Autel AL519 OBD2 Scanner, 2023 Newest Professional Mechanic OBDII & CAN Car Diagnostic Code Reader Tool for Check Engine Light, One-Click Smog Check, DTCs Lookup, Upgraded Ver. of AL319/ MS309 a.co/d/4YDeOfl
@@MrtalentedReid okay thank you
@nanaross3598 you are welcome
Thanks for sharing
Your welcome
Looks different then the one I got. IT had the plug at the top & only 2 bolts? Mine is a 2009
Okay just have to keep looking online or get a dealership to order it for you
What check engine code does this trigger?
- P2120: Accelerator Pedal Position Sensor (APP) Circuit
- P2121: Accelerator Pedal Position Sensor (APP) Range/Performance
- P2122: Accelerator Pedal Position Sensor (APP) Voltage Low
- P2123: Accelerator Pedal Position Sensor (APP) Voltage High
- P2125: Accelerator Pedal Position Sensor (APP) Intermittent
@@MrtalentedReid Thanks much!
Oh sorry same part # for a 2009 Murano?
This could be very helpful to me because my car starts and runs great but at speeds between 30 and 45 mph, it gets crazy! It pulls back and pulls forward simultaneously! I thought it might be the TPS! Thank you! I'll check this out first!
Ok your welcome
I have a 2003 Nissan Sentra ser and I got the code p1122 you think it can be the pedal it only revs to 2000 rpms and accelerates to 10-15 mph
Thanks for stopping by. So it could be a bad throttle body, bad pedal sensor, blown fuse bad pcm, bad relay. But you can try a different throttle body first and see. And after you replace the throttle body clear the code. If that doesn't fix the problem try a different pedal sensor and continue checking all those things I send you.
@@MrtalentedReid ok thank you so much
You're welcome
I have a 2006 Nissan Murano and it idles fine when in park but when I put it in gear the gas pedal doesn't respond. I've replaced gas pedal twice and it still doesn't solve the issue
It could be a bad computer, tps, throttle body, broken wire bad fuel pump, so the best thing is to do it to scan it and see what code pops up
Mine does exact same thing,did you ever figure it out ?
I am having problems with my 2006 Nissan Murano, Changed Pedal, Changed Trottle body and still car won't accelerate. Once TPS or Pedal changed car drives for a while like 1km and it goes to limp mode with Slip light and VDC displaying a check engine light, when I disconnect the pedal cable the car get high acceleration can drive . But it's slow. please any suggestions for possible solutions?
Ok there are few things to change first check the speed sensors in the wheel second check the input and output Speed sensors on the transmission third check the abs brake module fourth check the steering angle sensor fifth check the wiring for and loose broken or slack connections of the wires sixth check fuses. So if all that I told you about Is in good shape maybe you have a defective computer or bad transmission
@@MrtalentedReid the car is able to move when I disconnect the pedal cable it goes to a high gear. So I don't know if the transmission can be bad and it still able to drive on its own when I disconnect the pedal cable and put the gear on drive D
Do you scan the car with a obd2 code reader ?
There are a few reasons why your car might be struggling to accelerate. It could be due to a problem with the timing belt, the spark plugs, or the fuel injectors. It could also be because you have a dirty air filter or a clogged fuel filter. The fuel system may also be low on fuel.
Will it accelerate when in park to full throttle?
My Murano stops accelerating while I’m driving it , could this be the problem?
It could blown fuse broken wire or bad throttle body
Can anyone tell me if these things can go bad ,without an check engine light or trouble codes being set?
Not often time but it is possible what is the car doing?
09 Murano, the car starts fine and idles good drives good with good pic up from complete stop. But randomly after a few minutes it will rev slightly high the a couple seconds letter the power come back to normal. It's random
Maybe a faulty throttle body or pedal sensor
Did you get a CEL code for this?
No
Any symptoms or reasons on why you changed it out?
Slow take off and check light keep popping up when about to take off and sometimes rev by it self idle up and down
Ok cool. Same problems I have now. Thank you
Your welcome
is there a relearn process once replaced with new pedal
No just make sure the ignition off thanks for stopping by
Can anyone help got Codes P1122 & P1126 Crank no start 2003 nissan murano,narrowed it down to either the pedal or the connector that plugs into the pedal does anyone know how to check the connector?
Try a new throttle body
@@MrtalentedReid replaced that new
New one
@@MrtalentedReid yes its new
Check if there is any broken wires are bad computer
Is is part # PPE1042?
www.ebay.com/itm/256285692032?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=h6jCfVIxRxS&sssrc=4429486&ssuid=LLdE44b0Szu&var=&widget_ver=artemis&media=COPY
Check ebay
my murano 2003 drives beautiful but sometimes after a couple or 50 miles it won't accelerate normal it accelerates very slow and once I turn it off and restart it starts accelerating fine again 😢
Could be a fault accelerator pedal sensor or throttle body
where can umi buy obesity for a 2003 murano
Autozone or Amazon
Has anybody ever figured this out ? Never seen for sure fix!
Apa tanda kalau sensor rosak
Non acceleration
Sir why did you change this? What were the symptoms
Wasn't accelerating