I just wanted to thank you for your Carrier 8000 video; it helped a lot. Last year I replaced the igniter on my nephew's furnace and this year it would not start which I tracked down from the blinking codes to be the induction motor. But something I had not noticed last year and which concerned me when I replaced the induction motor was that the flame showed up between and outside of the outer tubes a little. Looking at your video I could see that your furnace did the same thing. Thanks for making this video available. It really helped.
Thanks for the help. Before seeing your video, I was trying to locate the flame sensor on my Weathermaker 8000 - I am glad I found your video! I gave mine a cleaning and so far it's working better. I was having the intermittent problem of the hot surfaces coming on, the gas fires up then the gas would shut off- randomly. Other times it would work fine.
I have a 58wav111 which was installed in 1997 (17 years ago). It is working fine. I've had some A/C contractor come out to give me estimates on a new A/C. They all say I should replace the furnace at the same time because these furnaces can only be expected to last 20 years. Any comment about that?
Had mine since September 1993 still going strong in 2023. Only had to replace the blower under warranty when it was new and recently the igniter. That's it
@@springws14lbss No I didn't replace it, and it is still working fine. I switched to a different HVAC company, and it has never indicated any problems with the furnace when doing the annual checkup.
P G Crawford Did you find the solution for the squeal of the inducer? I replaced mine but i can still hear a noise coming from the inducer. I noticed if I put pressure on the inducer bracket, the noise goes away. I was thinking about putting wider rubber washers/hose on the 3 screws.
I have an older Weather Maker with the 3 site glass burner view. The gas compant said one of the flames is flickering which could be a cracked heat exchanger again it's 20 plus years old, just curious thanks
In most parts of the country, NG is really cheap so the added cost of installing a heat pump instead of an air conditioner is typically not worth it. Now if you have a propane or oil furnace, that’s a different story!
We have this furnace in our house. It will not come on by it’s self we have to flip the switch off and on for it to come on. When it is on it does not complete the cycle it turns off and throws the over heating code, any clue what could be wrong?
If its giving you an overheating code, check the filter to make sure it isn't dirty. Also check and make sure none of the return air vents are blocked.
Just because you have nice blue flames when the blower comes on doesn't mean the heat exchanger isn't cracked. These carrier style furnaces are known for cracking.
I had a newer version of this furnace for 12 years. according to the HVAC ppl the AC was wired wrong and delivered 120V to the control board instead of 24V. Since the furnace was installed by them 12 years ago and took 12 years to catch fire apparently, yet they were astounded as to how it went so long psh. and 2 weeks after being forced to install a new "high efficiency" am i regretting not asking the installers more questions. I don't know what model carrier I had but it was 80% efficiency 2 stage and installed in 2006. the new one is an Amana GMSS96 (goodman) and the inducer blower sounds like a mini jet taking off. Then the blower comes on and sounds like a wind storm, is there anything I can do?? or have i just had the worst furnace installed in my home?
Is the newer furnace the same size as the old one? Since its new and has no dust on the blower wheel, its probably moving more air, thus creating more noise.
It was disconnected at the T-Stat because a "dual fuel" thermostat was not installed. The thermostat has since been replaced with a Honeywell VisionPRO 8000.
Got the same unit. Right now it'll be a bit slow going through all the stages to get going, and when the flames actually get going, they will only stay on for a few minutes at most, then they will go out. Should I just start pulling stuff off and cleaning it? It's not too dirty in there.
Thank you for posting this. I was having furnace trouble with our Weathermaker 8000. This video lead me to th-cam.com/video/I86joWL66aE/w-d-xo.html and I was able to clean our flame sensor get our house warmed up. Thank you!
Can someone explain the filter operation to me. I can leave the filter in for 6-months, and when I take it out to change it, the filter looks new, except for the 1-inch that is sticking out of the furnace. It this the norm?
I have a a problem with my Weathermaker. It seems to be the same model as the one featured in the video. When I reset it and it runs the course of igniting the gas, it will shut off gas flow after 8 seconds or so. And then it will reignite them shortly after. It heats my house intermittently and inefficiently. At times it will be be working but most of the time it seems to be blowing cold air.
I just wanted to thank you for your Carrier 8000 video; it helped a lot. Last year I replaced the igniter on my nephew's furnace and this year it would not start which I tracked down from the blinking codes to be the induction motor. But something I had not noticed last year and which concerned me when I replaced the induction motor was that the flame showed up between and outside of the outer tubes a little. Looking at your video I could see that your furnace did the same thing. Thanks for making this video available. It really helped.
You're welcome
The blue flames are so cool only natural gas furnace can make this possible!
why? I have seen some really beautiful flame from LPG.
They both should look good if the appliance has been setup properly!
I Am Absolutely in Love with those Blue Flames ❤️
Great video, thanks for the walkthrough!
Thanks for the help. Before seeing your video, I was trying to locate the flame sensor on my Weathermaker 8000 - I am glad I found your video! I gave mine a cleaning and so far it's working better.
I was having the intermittent problem of the hot surfaces coming on, the gas fires up then the gas would shut off- randomly. Other times it would work fine.
What year did Carrier stop making the 58 gs/gp upshot burner style gas furnaces, they were my favorite!
Mine is 1996. Still working. Should i replace it with a more high efficiency
I probably would. They only last for so long.
I have a 58wav111 which was installed in 1997 (17 years ago). It is working fine. I've had some A/C contractor come out to give me estimates on a new A/C. They all say I should replace the furnace at the same time because these furnaces can only be expected to last 20 years. Any comment about that?
Did you end up replacing it yet? I would get the heat exchanger thoroughly inspected to see if a replacement would be needed.
Had mine since September 1993 still going strong in 2023. Only had to replace the blower under warranty when it was new and recently the igniter. That's it
@@springws14lbss No I didn't replace it, and it is still working fine. I switched to a different HVAC company, and it has never indicated any problems with the furnace when doing the annual checkup.
@@docgonzo1973 Glad to hear it. Mine is now 26 years old and still running well without any problems.
What's going on when the draft inducer makes a high pitched squeal when the furnace starts?
P G Crawford Did you find the solution for the squeal of the inducer? I replaced mine but i can still hear a noise coming from the inducer. I noticed if I put pressure on the inducer bracket, the noise goes away. I was thinking about putting wider rubber washers/hose on the 3 screws.
Could be a motor staring to go bad/bad bearings.
I have an older Weather Maker with the 3 site glass burner view. The gas compant said one of the flames is flickering which could be a cracked heat exchanger again it's 20 plus years old, just curious thanks
It could be a cracked heat exchanger. I would have a professional HVAC company check it out before the upcoming winter.
I use to have one of those but it malfunctioned I got a new one now its a more modern furnace with the plastic pipes
I actually visited this place a few weeks ago and this one is still here!
@@springws14lbss Nice
I would really like to know where the pilot light is in this furnace I can’t find it Thank you
It does not have one, the burners are lit automatically by a hot surface igniter.
Is it digital or manual? There are some older, manual, heat only thermostats that don't have the option of controlling the fan separately.
Is a hybrid system worth it and cost effective? Or is it cheaper to just be pure natural gas.
It would all depend on the rate of your gas and electricity.
In most parts of the country, NG is really cheap so the added cost of installing a heat pump instead of an air conditioner is typically not worth it. Now if you have a propane or oil furnace, that’s a different story!
Is it a concern that the "draft induser" sounds like squeaky? Runs great and warms up the house but it sounds quietly like a bad belt on a car
It probably has a bearing that is starting to go bad and will likely need to be replaced soon.
My dad has a larger version of this furnace, only it's not a weathermaker.
We have this furnace in our house. It will not come on by it’s self we have to flip the switch off and on for it to come on. When it is on it does not complete the cycle it turns off and throws the over heating code, any clue what could be wrong?
If its giving you an overheating code, check the filter to make sure it isn't dirty. Also check and make sure none of the return air vents are blocked.
When you say you also have a heat pump, does that mean you have a hybrid heat system?
Yes.
Just because you have nice blue flames when the blower comes on doesn't mean the heat exchanger isn't cracked. These carrier style furnaces are known for cracking.
True, but in extreme cases of heat exchanger cracking, the blower can cause the burner flames to change shape or flutter.
So what exactly does the Igniter do Ive been wondering
Lights the fire!!!
I had a newer version of this furnace for 12 years. according to the HVAC ppl the AC was wired wrong and delivered 120V to the control board instead of 24V. Since the furnace was installed by them 12 years ago and took 12 years to catch fire apparently, yet they were astounded as to how it went so long psh. and 2 weeks after being forced to install a new "high efficiency" am i regretting not asking the installers more questions. I don't know what model carrier I had but it was 80% efficiency 2 stage and installed in 2006. the new one is an Amana GMSS96 (goodman) and the inducer blower sounds like a mini jet taking off. Then the blower comes on and sounds like a wind storm, is there anything I can do?? or have i just had the worst furnace installed in my home?
Is the newer furnace the same size as the old one? Since its new and has no dust on the blower wheel, its probably moving more air, thus creating more noise.
Mine makes a dog yelping sound when the ac unit kicks on, what is making this noise?
Could be the bearings in the blower motor starting to go out. You'll probably have to replace the motor.
I think I’m realizing somethings wrong with my heater. When mine kicks on for the draft it sounds like a train.
Probably a bad bearing in the motor.
I'm confused, was the heat pump running with the furnace?
It was disconnected at the T-Stat because a "dual fuel" thermostat was not installed. The thermostat has since been replaced with a Honeywell VisionPRO 8000.
Got the same unit. Right now it'll be a bit slow going through all the stages to get going, and when the flames actually get going, they will only stay on for a few minutes at most, then they will go out. Should I just start pulling stuff off and cleaning it? It's not too dirty in there.
Check and see if you are getting any error codes on the control board first. Otherwise, might need the flame sensor cleaned.
whats going on when furnace stop red lite blinks
Check the inside of the access panel for code information.
It is giving you an error code. The codes should be listed on the inside of the blower door.
led light stays on but no action just exhaust fan runs I replaced sensors still will not fire
Check your pressure switch. Do you have power going to the igniter at all? Might need to call in a service tech.
Thank you for posting this. I was having furnace trouble with our Weathermaker 8000. This video lead me to th-cam.com/video/I86joWL66aE/w-d-xo.html and I was able to clean our flame sensor get our house warmed up. Thank you!
Can someone explain the filter operation to me. I can leave the filter in for 6-months, and when I take it out to change it, the filter looks new, except for the 1-inch that is sticking out of the furnace. It this the norm?
Depends on how often the unit is running. What type of filter are you using?
The lovely Chicago controls landlord stat. Those should be outlawed
I have a a problem with my Weathermaker. It seems to be the same model as the one featured in the video. When I reset it and it runs the course of igniting the gas, it will shut off gas flow after 8 seconds or so. And then it will reignite them shortly after. It heats my house intermittently and inefficiently. At times it will be be working but most of the time it seems to be blowing cold air.
Sounds like the flame sensor is dirty, try cleaning it.
@@springws14lbss thanks
That's a horrible place to install a condensing unit! It doesn't have enough space to breathe efficiently!
I know but what can you do, the landlord had it done that way.
Has your Carrier ever done what mine does? The gas at the beginning of start up will be sporadic. See here: th-cam.com/video/rhqZCRAFm1M/w-d-xo.html
Probably dirty crossovers in the burners. Schedule an HVAC tech to come out and look at it.
Is it digital or manual? There are some older, manual, heat only thermostats that don't have the option of controlling the fan separately.