Normally I'd say it'd be better to bleed it into an empty bottle and add fresh fluid - but for the ease of it and speed of bleeding the clutch - I'd say it's a good way to bleed, since the end of the pipe is in the reservoir, you don't get any air coming back, only fluid if anything. After it's done you can always just replace part of the fluid in the master cylinder tank anyway, so definitely useful stuff.
Well explained, useful video. Especially the trick how to press the metal pin in order to open the bleeder. I knew how to do it but I couldn't open it. After watching this the cluch fluid is replaced in minutes. Many thanks!
The clip and connector likes to stick. I lubricated Nissan Tiida 2008 with spray lubricant and it loosed up. The clip pushes down while you pull the connector sideways. I did the same thing with my Nissan Almera 2013 clutch and the connector pulled completely out and dropped the entire master cylinder brake fluid on the ground. The clip does completely different things on different models. The almera clip is totally sheit to say the least.
yeah thas about it, only thing i do diferent is not blead it into the brake reservoir, so it dont contaminate the brake fluid on the brake system......................................
I recently changed clutch and master slave clyinder in my nissan juke but the gears often get stuck and i have to pump the clutch few times to make it work again. Any idea what can cause it ?
Why you bleed it did you just replace the slave cylinder that's why ??? My slave cylinder is leaking inside gearbox what should do is there any chance of stop this leak 🤔 thanks
When I put in the second position it doesn't lock, because after the bleeding there pressure on the clutch and when I press on the clutch pedal it unlocks and get on first position. Can you give me any advice to how to lock it properly so that it stays on first position
Thank you for posting this... My 2013 Australian delivered Nissan X-Trail with the Renault 6 Speed Gearbox has this setup also... It worked a treat.
👌👌👍
Thank you, I was trying to figure out how to use that bleed whole. Much appreciated.
Thanks for posting this. Worked a treat on our Nissan Tiida 2007. Its not identical but works on the same principle
Normally I'd say it'd be better to bleed it into an empty bottle and add fresh fluid - but for the ease of it and speed of bleeding the clutch - I'd say it's a good way to bleed, since the end of the pipe is in the reservoir, you don't get any air coming back, only fluid if anything. After it's done you can always just replace part of the fluid in the master cylinder tank anyway, so definitely useful stuff.
Thanks for the great video and clear explanation, much appreciated
Any time 🙏
Well explained, useful video. Especially the trick how to press the metal pin in order to open the bleeder. I knew how to do it but I couldn't open it. After watching this the cluch fluid is replaced in minutes. Many thanks!
Any time 🙏
The clip and connector likes to stick. I lubricated Nissan Tiida 2008 with spray lubricant and it loosed up. The clip pushes down while you pull the connector sideways. I did the same thing with my Nissan Almera 2013 clutch and the connector pulled completely out and dropped the entire master cylinder brake fluid on the ground. The clip does completely different things on different models. The almera clip is totally sheit to say the least.
yeah thas about it, only thing i do diferent is not blead it into the brake reservoir, so it dont contaminate the brake fluid on the brake system......................................
I recently changed clutch and master slave clyinder in my nissan juke but the gears often get stuck and i have to pump the clutch few times to make it work again. Any idea what can cause it ?
Cool, thank you very much. I was looking at the procedure on AllData and about to have an anurism.🤬
🙏
tank you, very nice explained
Thanks for the video Aziz
Mar7ba khoya
Shokran video help me fix my car
Thank You!
Dziękuję za uratowanie życia!!! Pozdrawiam z Polski ❤❤❤
Obrigado por compartilhar, tinha dúvidas sobre o procedimento.
My cluch peddle went to the floor and I went to install a new master and bleed it and noticed I’m missing the clip 😭
From 🇲🇽 gracias!!!!,👍
Why you bleed it did you just replace the slave cylinder that's why ??? My slave cylinder is leaking inside gearbox what should do is there any chance of stop this leak 🤔 thanks
Hi no the only way is to replace it
@A&N Vlog ok ...thank you
Muito obrigado salvou parabéns pra vvcs
Thanks a lot
Thank you
🙏
Hi o my scenic2 is problem ,what to do??
Meri duster m kabhi bhi clutch kaam krna bilkul bnd kr deta h to kya kre??
When I put in the second position it doesn't lock, because after the bleeding there pressure on the clutch and when I press on the clutch pedal it unlocks and get on first position. Can you give me any advice to how to lock it properly so that it stays on first position
hi, did yo find a solution to your problem?
Shokran bizef
Mar7ba
Ni
Esy chang kaisy kry
🤔
Yalla hamuda press habibi 😂😂. Sorry❤
Hamouda 04
Thank You!