Hello Rajas I hope you doing good. After looking your videosI got inspired and started my own rx 135 restoration project and looking ahead for part 4 of disassembly of the engine...
hello Aap Jo video banate Ho bahut hi Sundar Hai Dekhne Mein bahut maza aata hai samajh mein bhi aa jata hai kaise tarike se gadi thik hoti hai tu but ek baat hai mera mera Bharat mein rehta hoon Bardhaman Main Mera Naam panchanan Dhara mere paas ek
Nice 👌 Excellent hacks for safe removel of magneto, clutch basket and crank nut. 👍 Bro, I have begun on my 135 , stored for 4 years. Sucessfully removed and cleaned, tank, fuel cock, seat, air filter, carb, energy box and reed valve. I am struggling to loosen oil pump cover 3 screws as they have hardened. Tried with WD40, coconut oil, but still tight. Now the screw head star grooves are rounding loosing screw driver grip. How to loosen these screws without damaging the screws? Same problem also on one of the screws on the petal of reed valve. Hoping you can guide.... Thanks
Hi can u please help. My Rx135 engine stops when I put in gear and try to release the clutch. As soon as I release clutch, the engine stops. What is the problem and solution for this
Rajas bhai . Excellent video. I have been following the engine videos by you. I want to buy special tools for Yamaha 100 135 . Where can I get them . I didn't get on google . Please help me bro. Thanks a lot.
rajas on your video of RX100 restoration you have uploaded I have done restoration of my RX 135 and now especially RX135 with a better quality is like a feast for me it doesn't matter how many views and like to your video second thing i have some anoying piston tak tak sound from ENGINE BORE not much loud but you can hear it It happened after my restoration ANY ADVICE?
krishna jadeja - My Rx135 too was rebored recently. I don't have much knowledge about bikes and I took it to a mechanic for service after someone recommended him as Yamaha specialist. I just asked him to check how the bore looks like as my bike was really slow and mileage was very low. I left the bike with him and went home. He called me up in the evening and said bike was serviced and the engine was rebored to .5mm but the bike was running on a standard size. I asked him why he bored it to .5mm but it should be .25mm. He didn't give me proper answer(I guess he had a .5mm piston and wanted to sell it). When I rode the bike, I heard the tak tak sound from the cylinder but he said it is fine. Now the Bike has done 500kms after rebore but still there is this sound, not sure what to do. Sometimes, if I rev it hard, the sound goes away.
This is a very common problem .....can be because of many reasons ....try using 40 to 50ml oil per litre of petrol in the breakin period....that might solve it
Bro one humble request pls explain Yamaha rx 135 parts names and uses example AC kit how to change oil because in four stroke we can remove oil bolt in underto remove waste oil but Yamaha why pls explain reason in video
Hello I have this same model of RX135 2001 model . I am looking for its source coil actually source coil of Rx100 and Rx135 old are different so plz help me . How do I contact you.?
Main panchanan Dhara mere pass RXZ Hai Uska starting coil kharab ho chuka to dusra Koi Lagane se Agar start ho jaaye toh bahut hi Meherbani Hogi ab Jara bataiye
When driving .. at low throttle it works as usual .. but when I increase throttle it seems like it comes down to reserve or no petrol carburator was cleaned air filter also cleaned ..... kindly suggest a way
Hello Rajas I hope you doing good.
After looking your videosI got inspired and started my own rx 135 restoration project and looking ahead for part 4 of disassembly of the engine...
Absolutely loving this restoration project........>>>
Thanks very much for your video. I've learnt how to lock the crank so that I can get a nut off! 🇮🇳🇬🇧
Love ur work and ur back ground music..... Toooo...!!!! Keep it up bro.... And thanksssss for sharing a video like dis .....
Good job .Keep it up ! We need more such engineers like u. thanks
Too much professionalism in one video 😎👌
I like your videos very much and you are master of rx series motorcycles.
Indonesia RX KING 135 😎
Muito bom ,ótimo trabalho
Nice work restored
thanx to your videos i have successfully opened my 1996 RXG engine... CHEERS
BTW what size of bolt was used for the JUGAAD type flywheel/magneto puller
I think thats 10 mm ....I'm not sure ...if not try 8mm
Very detailed, good video
All video are in super standard..
man you are a great
Bro you awesome.!!👍🤘
Thanks for ur video and video quality is good 👍👍👍
hello Aap Jo video banate Ho bahut hi Sundar Hai Dekhne Mein bahut maza aata hai samajh mein bhi aa jata hai kaise tarike se gadi thik hoti hai tu but ek baat hai mera mera Bharat mein rehta hoon Bardhaman Main Mera Naam panchanan Dhara mere paas ek
One word ... love
engine full fitting ke baad gadi kaise start krna hai usko v btana plzz bahut jaruri hai ye
good and neat work my bike is having problem and want to get the bore checked if needed put a new cylinder
Nice 👌 Excellent hacks for safe removel of magneto, clutch basket and crank nut. 👍
Bro, I have begun on my 135 , stored for 4 years. Sucessfully removed and cleaned, tank, fuel cock, seat, air filter, carb, energy box and reed valve. I am struggling to loosen oil pump cover 3 screws as they have hardened. Tried with WD40, coconut oil, but still tight. Now the screw head star grooves are rounding loosing screw driver grip. How to loosen these screws without damaging the screws? Same problem also on one of the screws on the petal of reed valve. Hoping you can guide.... Thanks
Hi can u please help. My Rx135 engine stops when I put in gear and try to release the clutch. As soon as I release clutch, the engine stops. What is the problem and solution for this
Good Job Rajas
Thank you bhaiya :)
I like u..l'm from Indonesian
Aku malah wong jowo wkwkwk
Bro my rxg 135 has ceased can u advice me for which cylinder kit i have to go
Was there no centre gasket?
Good evening sir I have a question for you I have a oil leak around. My drain plug so how I fix it or stop it please reply thx
Good evening again sir my bike is a Yamaha rxs 115 pk
You are great! You are spreading the knowledge you have, that is a noble thing you are doing! Keep it up bro! 👍🏻👍🏻👍🏻
Thank you Dada 😊😚😚
@@RajasGadkari bhai mast video hai but remove the madarchod music
Great content as usual except the music is a bit overpowering the audio :)
Yes right ....sound levels are all over the place ... I'll make sure this does not happen in future
It's very nice
Make a wiring installation video pls bhaiya
What is yeis technology???
Must add 135 best alter engine tips
Rajas bhai . Excellent video. I have been following the engine videos by you. I want to buy special tools for Yamaha 100 135 . Where can I get them . I didn't get on google . Please help me bro. Thanks a lot.
Hey great vid. Are you a mechanical engineer ?
Original engine ka kimot kitna?
Super.anna
Bro I've got yamaha rx135 2005
Model, there's a problem with 2t oil which is directly going into chamber. Is there any solution for the same
🤘❤
Hi Rajas Gadkari can u please upload a video on how to Install a tachometer (rpm) in YAMAHA rxz
Next time bro please mention that size of using spanners...
sir, plzz make a video to set a float height in carburetor, my request....
Amazing
rajas on your video of RX100 restoration you have uploaded
I have done restoration of my RX 135 and now especially RX135 with a better quality is like a feast for me it doesn't matter how many views and like to your video
second thing i have some anoying piston tak tak sound from ENGINE BORE not much loud but you can hear it
It happened after my restoration
ANY ADVICE?
krishna jadeja - My Rx135 too was rebored recently. I don't have much knowledge about bikes and I took it to a mechanic for service after someone recommended him as Yamaha specialist. I just asked him to check how the bore looks like as my bike was really slow and mileage was very low. I left the bike with him and went home. He called me up in the evening and said bike was serviced and the engine was rebored to .5mm but the bike was running on a standard size. I asked him why he bored it to .5mm but it should be .25mm. He didn't give me proper answer(I guess he had a .5mm piston and wanted to sell it). When I rode the bike, I heard the tak tak sound from the cylinder but he said it is fine. Now the Bike has done 500kms after rebore but still there is this sound, not sure what to do. Sometimes, if I rev it hard, the sound goes away.
This is a very common problem .....can be because of many reasons ....try using 40 to 50ml oil per litre of petrol in the breakin period....that might solve it
me too facing this problem.... tik tik sound
Bike restoration karne ke bad video dal yar please.......
What is the resl price of the otoginal engine of Yamaha RX 135???
Bhai i need to show u my rx 100 1986 japan engine bike how can it be possible in mumbai im from western side plz let me know
Sir I have a problem in my Rx 135 can u help me
What is the cost for full engine restoration
Really a good one✌🏼✌🏼
Krennn
Add a video clutch oil seals
More add bro about 135 alter
I want change my bike's engine
Hello brother..how do I contact you?
Bro one humble request pls explain Yamaha rx 135 parts names and uses example AC kit how to change oil because in four stroke we can remove oil bolt in underto remove waste oil but Yamaha why pls explain reason in video
Boss I have a Rx 100 how much will you take to do full restoration
That will depends on the work.
I have a 30 years old Rx 100 just tell me how much it cost to do the engine work
Hindi m bolo Bhai
Hello I have this same model of RX135 2001 model . I am looking for its source coil actually source coil of Rx100 and Rx135 old are different so plz help me . How do I contact you.?
ok i can ship you the coil if you want .....you can mail me on rajasgadkari@gmail.com or dm me on instagram @rajasgadkari
@@RajasGadkari ok I really need source coil and pick up coil
Bro we can work with you
Main panchanan Dhara mere pass RXZ Hai Uska starting coil kharab ho chuka to dusra Koi Lagane se Agar start ho jaaye toh bahut hi Meherbani Hogi ab Jara bataiye
Mera WhatsApp number hai 892 7033 912
Bike restoration kare ke bad video dal
When driving .. at low throttle it works as usual .. but when I increase throttle it seems like it comes down to reserve or no petrol carburator was cleaned air filter also cleaned ..... kindly suggest a way
Check the pickup coil and mainly the CDI unit.
Me and my friends want to work on rx135 can you help us through video call or something ..we can pay also ..thanks
yes definitely ....you can mail me at rajasgadkari@gmail.com or dm me on instagram to discuss further.
Salo like marna sikho kamse kam.. banda jhat khujlane ki liye video nahi banaya..
very sloppy hand, and use ratchets please, don't force us to watch you trying so hard in unnecessary things
Very sloppy feedback .... please don't watch my videos
also I'm just glad that you didn't measure clutch plates with ruler
Ni men your chanel is very good