PART 2 with MJJC Groits etc th-cam.com/video/iTQDalUE5N0/w-d-xo.html NOTE: AstroAI Spec sheet says 1.25mm office installed, mine actually measured just over 1.mm multiple times. It's hard to say if mine was a defect, but others are saying they are getting similar results with low PSI/GPM pressure washers.
This is bar none the best review of products I have ever seen for any product on YT. You were clear and to the point. Provided guidance on features to look for included a detailed chart with comparative features. Outstanding job. Thank you.
Thanks, Yeah I wanted something consistent. Yep I think the orfice size is something that is commonly overlooked, but defiantly impacts the performance. Also most won't need or have a gas pressure washer so having the right orfice is key.
Thank you for this. Helped inform my purchase. I found that Tool Daily also carries an upgraded version of the base model you reviewed, fittings seem to be the all-brass of the base model, but bottle is plastic on plastic fitting with a wide mouth and wider base, still comes with extra nozzles, and what looks like the plastic adjustment shielding from the 1.5 liter model.
You just saved me a lot of time and money watching your video. Thank you. I just purchased the number one pick AstroAI along with a set of 1.1 orifices.
My HF foam cannon came with a 1.1 orifice in the box. I had already ordered a set of 1.1 orifice from Amazon before I found out you can't change the one in the Armor All 2 in 1 foam cannon. Armor All makes a foam cannon, that doesn't have that switch on the side, that does have a orifice you can replace. The 2 in 1 that comes with the garden hose handle can not be replaced, it's just a ball valve with two different size holes controlled by the handle on the side. My HF foam cannon is working great after I installed the 1.1 orifice.
Great testing, great summary/ranking to make it more understandable rather than just showing the testing, and the detailed chart is also nice. Thank you!
I have had a $10 foam cannon from Amazon for about six years and I rinse it out after every use with clean water. It's still working fine. A foam cannon shouldn't cost upwards of $100 when they have the same amount of money in the design and materials as the $10 foam cannons. Think about that. Don't get me wrong, I do also have a Griot's Garage BOSS and Griot's Garage Brilliant Finish foam cannon and I love both of them. The BOSS is PRICEY but it adds the ability to use metering tips to draw chemical from 8, 16, and 32 oz bottles with the correct thread (which most have since it's a standard). I like being able to hook up my chemical bottle right to the cannon head and draw from the metering tips as it saves a bunch of product from waste typical with the bottles on the bottom of the foam cannon. You can also use the tips in the Brilliant Finish Foam Cannon but they need to be purchased from Griot's separately. The Brilliant Finish cannon is about half the cost of the BOSS and they perform almost identically. The issue with the bottle included with the cannon is you mix up your solution and then you don't use it all so you've then wasted product. The metering tips allows you to use exactly the amount you need and then clean out the foam cannon head with clear water and you are good to go for the next wash session. The $23 cannon you show here should give most enthusiasts all they will ever need. Just clean out your foam cannon with clear water after use and you should get years of service out of it. Don't get sucked up into the hype of needing thousands of dollars worth of pressure washer equipment and expensive tools and chemicals. There are MANY options out there that work just as well for much less money.
Paid $15.00 each for a two-pack of the bigger bottle Tool Daily cannons, and they came with a little wash mitt along with the extra orifice and other bits. Really happy with them.
Thank you for this video clip. Excellent products review, no crap and unnecessary data, very helpful and easy to follow. I am in the market for a foam cannon and this helps a lot. Once again, much oblige. Keep up with good work. Best regards from the old north state.
NOTE: AstroAI Spec sheet says 1.25mm office installed, mine actually measured just over 1.mm multiple times. It's hard to say if mine was a defect, but others are saying they are getting similar results with low PSI/GPM pressure washers.
Can confirm your’s is a fluke. Bought the AstroAI & mine came w/ a 1.25mm orifice. It doesn’t help that AstroAi Direct on Amazon is telling most people 1.1mm in the Q&A section, but then also says 1.25mm to some & the product came w/ a 1.25mm for me.
I watched this 3 times and have bookmarked it. Very thorough review and covers a range of price prices. Thanks for this, Liked & subscribed! Oh and I ordered the AstroAI!
MJJC v2 would have been the top dog in this test. I have two after so much research. Also on the Harbor Freight. I have two as well and the best mod is the 1.1 needs to be installed. I use a AR630 pressure washer which helps as well.....
9:26 tool daily - I really wanna see more of this one , been looking at getting the MGGC but with that price point if it can be close I’m down, it looks cool too
Great comparison wanted to know. Can you use a hose set of on any of these? Or do you need to have the electric or gas pressure washer? And if you can use a hose Does it do a decent job
Thanks! all except for the armorall you will need a pressure washer. I couldn't get the armorall to work with or without a pressure washer. That being said others claim it works, but I can only speak from experience.
Love your vids bro. I'm going with the AstroAI. Now, just need help finding a electric pressure washer that has the quick connects. Any ideas that can be under $200?
Why do you prefer plastic-on-plastic as opposed to brass-on-plastic? I'd think that brass is always desirable for longevity. Does it tear up the plastic jug's threads? Not a video topic I would have thought of, but thank you, as always! I don't really know anything about this product segment - it's actually something I was just telling myself a few days ago that I'd likely avoid DIYing most detailing work, but then, I'm debating if I shouldn't dismiss it so quickly, until I at least look at pricing on starter kit. This test certainly helped give me something to consider! Glad to see that a cheap tool gets the job done so well!
Paint and body work makes me nervous. Seems like a lot of complicated, touchy stuff, that's almost more art form and nuanced, rather than clear-cut and technical, the latter of which I'm more comfortable with. I certainly admire the work and setups at AMMO NYC and Obsessed Garage, but I'm really not sure how deep down those rabbit holes I want to play.
Yeah the plastic threads can get damaged screwing into brass, not a major deal if your careful. I had a few requests to do one last year, but I for the life of me couldn’t find the harbor freight version in stock until a few months ago. I agree, detailing and doing any kind of body work is a art. Definitely when it comes to paint matching. I watch obsessed garage, his ocd is crazy. I can’t ever seem to buy anything in perfect condition to start with lol. Yeah I was shocked the cheapest one 🏆, which I agree is a win.
I can't seem to find a review for the Westinghouse: Pressure Washer Foam Cannon - 3600 PSI, 1/4 in. Connector, Model # PWFC, would you please do review of this product, I value you thoughts. Great video. Thanks
Can you use a 1.1 oriface safely with a gas pressure washer? I have an old(ish) craftsman that I would like to utilize and the AstroAi is looking like the ticket. Thanks!
I have the MTM foam gun that I use with a gas powered 3300 psi pressure washer and it doesn’t foam like it should. It comes out too watered down. I’ve tried adjusting the foam gun and the psi on the pressure washer, but it didn’t help. Any thoughts?
Thanks, no problem! Yeah I didn't know either until I started doing research on them. Interesting to see the difference with the electric pressure washer.
You must try the Ridge Washer foam cannon - $20 and comes with a nice wash mit. Its the green label and comes with a 1.15 orifice. I'm getting amazing foam with the Ryobi 1800 psi electric pressure washer. I'm talking gas pressure washer - like foamage from this thing. Its a sleeper of a foam cannon.
The tool daily # 2 works good when you change the orific to a 1.1 foams like crazy, the only problem I have with them is the bottle is cheaply made and broke on me now I can’t find a replacement
I have a maybe dumb question, but can the Astro be mounted to a karcher high pressure washer, or do I need to order an adapter for it? Thanks for letting me know
I ordered the AstroAI and it looks like it comes with a 1.25mm inner core diameter according to the manual. It works well with my electric Ryobi pressure washer regardless.
using a 1.0 orifice will trip your breaker on your washer or your outlet unless you're running on a dedicated 20Amp circuit 1.0 orifice reached 17.4 amps using the Astro A.I. cannon. I swapped for a 1.1 and went down to 14.2 amps ..safe
Great video! I think I'll pickup the new MTM Hydro foam cannon. I have the 1st gen version and used it for about 4- years, 100s of times. Best quality stuff you can get from MTM!
Thank you for the amazing comparison and I will def buy the tool daily foam canon with my Ryobi 1.2 PW Electric . But can you suggest something affordable wand too sir? like the short Quick connect wand?
No problem! Wands I currently cant speak for, I only have the MTM. At some point I would like to review and test some but it will be a while before I can.
I bought the Astro Ai one and changed to a 1.1mm orifice. I'm using Chemical Guys Mr. Pink. I'm still not getting really thick foam. Could my gas pressure washer be too powerful? 2200 to 2900 PSI and 2.3 GPM.
I don't think the pressure washer is too powerful. I would try a higher concentration of soap if you haven't already, maybe run strait soap and see how it performs. Also might turn the adjustment in the opposite direct and see if it changes anything. I remember some of the ones I test they seemed to be labeled wrong on the nob. If that dousing work maybe you received a defective one, with that flow and GPM you shouldn't have an issue.
It's just some hydraulic fittings, a flow meter for water and a digital pressure gauge, with a MTM gun. That way I could get the GPM of the pressure washers and also working pressure at the same time using the same tip.
I just purchased the Astro AI and it came with a 1.25 orifice installed. There wasn't another one to change it out to. I was disappointed because I went off your recommendation and it didn't come with a 1 like you said but a 1.25.
Maybe mine was an error, I know it measured 1.03mm with my gauges while the manual says 1.25. I will probably order another one next year and see if that one measures the same.
Lol yeah, the worst part is I had to do it almost twice because of the glare when the sun came out. I didn't notice it until editing the video... Thanks for the sub!
Nice, I'm actually shocked how well the cheap Ryobi did. At some point I would like to test electric pressure washers. How's your 30g doing? I'm almost at 500hrs.
@@marlondeere3039R Nice, yeah I agree AC could be better. I was going to look at adding some refrigerant but I haven’t had a chance to put gauges on it. No tractor kinda been a disaster, finally got the brake valve fixed. The dealer has been cycling through service mangers after the buyout. I think they are on #5 in two years… Deere never came out on changing the wiper and stuff but like a month or so after that call they stopped making the 5r. So yeah dealing with my dealer has been challenging to say the least. FYI I moved the outdoor videos to a new channel. Beaver Creek Acres
@Tools-Tested I owned 2 Ryobi electric PW and threw them away. Failing GFCI plug, Weak pump not keeping pressure, to full out failure. I just picked up the Chemical Guys PW. I hope this one lasts longer than 3 to 6 months like the ryobis.
So if its being used on an electric pressure washer it will likely need the 1.1 so it foams vs runny suds, this is because most electric washers have a lower psi and gpm. I did look at the Active 2.0 pressure washer, looks like a sold unit. But hard to say performance wise without testing it. You might check out Obsessed Garage if u haven't already, Mike's testing is thorough. th-cam.com/video/CVoQ5qyfxuw/w-d-xo.html
@@Tools-Tested WOW!! I believe it!! I actually bought the AstroAI after watching this. Just used it today a few hours ago and it is AMAZING FOR $23!!!!
This comment is for Tools Tested. The AstroAI guy I talked to on the phone read the manual and said the orfice size must be 1.25 and wondered where you got the 1.0 information.
Yes the book says 1.25, but mine was around 1.0. I used a drill hole sizing tool. Without ordering another one I can’t say If it was a error or if that’s how they all are coming now. But mine is definitely not a 1.25 or even a 1.1.
PART 2 with MJJC Groits etc th-cam.com/video/iTQDalUE5N0/w-d-xo.html
NOTE: AstroAI Spec sheet says 1.25mm office installed, mine actually measured just over 1.mm multiple times. It's hard to say if mine was a defect, but others are saying they are getting similar results with low PSI/GPM pressure washers.
Outstanding, no BS comparison and review. No annoying rock music no annoying silly fast-forward nonsense. Just great content! Thank you.
Thanks! Glad you liked it!
Thanks! Very thorough and I really appreciate you for saving me time and money!
Glad to hear it help! Thanks for the support!
This is bar none the best review of products I have ever seen for any product on YT. You were clear and to the point. Provided guidance on features to look for included a detailed chart with comparative features. Outstanding job. Thank you.
No problem! Im glad you liked it and found it useful. Thanks!
I think that’s the cleanest wall in the world
Not anymore... round two coming soon.
@0:51 - Ryobi Soap Applicator
@1:01 - Armor All Garden Hose
@1:08 - Armor All Electric PW
@1:17 - Armor All Gas PW
@1:29 - Green Earth Electric PW
@1:36 - Green Earth Gas PW
@1:42 - AstroAI 1mm Elec PS and Gas PW
@2:00 - Tool Daily 1.1 Elec PW and Gas PW
@2:19 - Tool Daily 1.23 Elec PW and Gas PW
@2:29 - Tool Daily 1.25 Elec PW vs 1.1 Elec PW
@2:50 - Harbor Fright 1.25 Elec PW vs Gas PW
@3:00 - Harbor Fright 1.25 Elec PW vs 1.2 Elec PW
@3:20 - Adams 1.25 Elec PW vs Gas PW
@3:32 - Adams 1.25 Elec PW vs 1.1 Elec PW
@3:53 - Chemical Guys 1.1 Elec PW vs Gas PW
@4:14 - MTM 1.25 Elec PW vs Gas PW
@4:25 - MTM 1.25 Elec PW vs 1.1 Elec PW
Worst Case Scenarios
@4:55 - AstroAI 1mm and 100% Soap Elec PW
@5:00 - Tool Daily 1.1 and 100% Soap Elec PW
@5:05 - Tool Daily #2 1.25 and 100% Soap Elec PW
@5:11 - Tool Daily #2 1.1 and 100% Soap Elec PW
@5:16 - Harbor Fright 1.25 and 100% Soap Elec PW
@5:23 - Harbor Fright 1.1 and 100% Soap Elec PW
@5:30 - Adams 1.25 and 100% Soap Elec PW
@5:35 - Adams 1.1 and 100% Soap Elec PW
@5:40 - Chemical Guys 1.1 and 100% Soap Elec PW
@5:45 - MTM 1.25 and 100% Soap Elec PW
@5:51 - MTM 1.1 and 100% Soap Elec PW
@5:57 - Adams Color Foam
@6:20 - Final rankings
Like and Pin
The amount of time soap and effort this took is much appreciated!!!!
No problem! Glad you enjoyed it!
Best comparison I have seen. Using the building for a flat surface is better than using a car. Comparing orifice sizes was interesting.
Thanks, Yeah I wanted something consistent.
Yep I think the orfice size is something that is commonly overlooked, but defiantly impacts the performance.
Also most won't need or have a gas pressure washer so having the right orfice is key.
Defiantly!
😉
TFS
👍🏻
agreed
Thank you for this. Helped inform my purchase. I found that Tool Daily also carries an upgraded version of the base model you reviewed, fittings seem to be the all-brass of the base model, but bottle is plastic on plastic fitting with a wide mouth and wider base, still comes with extra nozzles, and what looks like the plastic adjustment shielding from the 1.5 liter model.
No problem! Glad it helped!
You just saved me a lot of time and money watching your video. Thank you. I just purchased the number one pick AstroAI along with a set of 1.1 orifices.
Glad to hear it helped!
guy has the cleanest side of a garage in the history of buildings.
lol yep
I also got your recommended Astro foam cannon product as well. good video appreciate it. @@Tools-Tested
Nice, glad to hear it helped!
Ya sold me.
Just got on the AstroAI website and ordered one.
Thanks!
Glad to hear it was helpful! No problem!
how is the foam cannon?
Really great video. I really liked the use of the flat wall surface for testing how well each foam sticks. Cheers
Thanks! yeah it worked out well, hope to test a few more this year in the same manner.
My HF foam cannon came with a 1.1 orifice in the box. I had already ordered a set of 1.1 orifice from Amazon before I found out you can't change the one in the Armor All 2 in 1 foam cannon. Armor All makes a foam cannon, that doesn't have that switch on the side, that does have a orifice you can replace. The 2 in 1 that comes with the garden hose handle can not be replaced, it's just a ball valve with two different size holes controlled by the handle on the side. My HF foam cannon is working great after I installed the 1.1 orifice.
Hello. Your clear concise reviews helped a lot! Thank you.
Glad it was helpful! No problem!
Great testing, great summary/ranking to make it more understandable rather than just showing the testing, and the detailed chart is also nice.
Thank you!
I have had a $10 foam cannon from Amazon for about six years and I rinse it out after every use with clean water. It's still working fine. A foam cannon shouldn't cost upwards of $100 when they have the same amount of money in the design and materials as the $10 foam cannons. Think about that. Don't get me wrong, I do also have a Griot's Garage BOSS and Griot's Garage Brilliant Finish foam cannon and I love both of them. The BOSS is PRICEY but it adds the ability to use metering tips to draw chemical from 8, 16, and 32 oz bottles with the correct thread (which most have since it's a standard). I like being able to hook up my chemical bottle right to the cannon head and draw from the metering tips as it saves a bunch of product from waste typical with the bottles on the bottom of the foam cannon. You can also use the tips in the Brilliant Finish Foam Cannon but they need to be purchased from Griot's separately. The Brilliant Finish cannon is about half the cost of the BOSS and they perform almost identically. The issue with the bottle included with the cannon is you mix up your solution and then you don't use it all so you've then wasted product. The metering tips allows you to use exactly the amount you need and then clean out the foam cannon head with clear water and you are good to go for the next wash session. The $23 cannon you show here should give most enthusiasts all they will ever need. Just clean out your foam cannon with clear water after use and you should get years of service out of it. Don't get sucked up into the hype of needing thousands of dollars worth of pressure washer equipment and expensive tools and chemicals. There are MANY options out there that work just as well for much less money.
Your testing is greatly appreciated! Great info
Glad to hear it helped! Thanks!
How many times do you refill the foam cannon when washing a vehicle? More than once?
I would say probably only once, really depends on the size and how dirty the vehicle is.
Paid $15.00 each for a two-pack of the bigger bottle Tool Daily cannons, and they came with a little wash mitt along with the extra orifice and other bits. Really happy with them.
Yeah the Tool Daily performs well for the cost.
Is there any thing like this you can hook up to a regular gardrn hose ?
Thank you for this video clip. Excellent products review, no crap and unnecessary data, very helpful and easy to follow. I am in the market for a foam cannon and this helps a lot. Once again, much oblige.
Keep up with good work. Best regards from the old north state.
Thank you for this! Foam King and Chemical Guys was all I knew, so this reviewed saved me a lot!
Glad you found it helpful!
Thank you. I have that Ryobi & an Adam's foam cannon in the mail. I'll return it and get the one you recommended. You saved me $50.
No problem! glad it helped!
I really appreciate the detail in this video. It helps me to get one.
Thanks! Glad it was helpful!
NOTE: AstroAI Spec sheet says 1.25mm office installed, mine actually measured just over 1.mm multiple times. It's hard to say if mine was a defect, but others are saying they are getting similar results with low PSI/GPM pressure washers.
Can confirm your’s is a fluke. Bought the AstroAI & mine came w/ a 1.25mm orifice. It doesn’t help that AstroAi Direct on Amazon is telling most people 1.1mm in the Q&A section, but then also says 1.25mm to some & the product came w/ a 1.25mm for me.
I replaced the AstroAI orifice with a 1.1mm and saw no difference in the foam so I'm thinking mine did in fact come with a 1.1.
#FChina
#FAmazon
Problem solved
I went to change mine to a 1.1 and the installed one looked even smaller. Crazy to see, but im not mad. They also told me it was a 1.1
I watched this 3 times and have bookmarked it. Very thorough review and covers a range of price prices. Thanks for this, Liked & subscribed! Oh and I ordered the AstroAI!
Thanks! Glad to hear it was helpful!
Thanks for the SUB!
how is the astro ai?
@@princeshihot8583did you buy the astroai?
I have the tool daily, but is under a different brand. Bought it 7 years ago on Amazon. Still works fantastic.
Nice!
Should I use a 1.1 with a gas washer , or should I use 1.25 ?
Normally with a gas pressure washer the 1.25 will work good, if you would like it to foam a little more than I would install the 1.1.
What do you recommend for Ryobi 1800 PSI 1.2 GPM Electric Pressure Washer
Foam Cannon don't really have a budget
Great video....do you know which one that can spray up to 10 meters high up?
Thanks, I don't think any would reach anywhere near 10 meters, probably 3 max.
MJJC v2 would have been the top dog in this test. I have two after so much research. Also on the Harbor Freight. I have two as well and the best mod is the 1.1 needs to be installed. I use a AR630 pressure washer which helps as well.....
Yeah is missed MJJC, hopefully I can test the V2 and V3 next year!
Great video, I went with a Tool Daily recently. Can’t wait to use it.
Nice should work well!
If i use a 3000psi foam cannon on a 4400psi pressure washer could it break ?
Yeah it’s possible, I wouldn’t recommend it.
9:26 tool daily - I really wanna see more of this one , been looking at getting the MGGC but with that price point if it can be close I’m down, it looks cool too
Hey when you say 1.1 orifice for electric pressure washer, is that good for 2700 psi electric pressure washer?
Yeah I would still use the 1.1 for the best foaming.
Great comparison wanted to know. Can you use a hose set of on any of these? Or do you need to have the electric or gas pressure washer?
And if you can use a hose Does it do a decent job
Thanks! all except for the armorall you will need a pressure washer. I couldn't get the armorall to work with or without a pressure washer. That being said others claim it works, but I can only speak from experience.
Excellent breakdown of some good budget and mid-range options. Thanks a ton!
Thanks! Glad you found it helpful.
Excellent job! No BS with explanations of your ratings!
Glad you liked it!
I have 1800psi pressure washer should I get took daily or astroai ?
Electric
I would go with astroAI IMO
Love your vids bro. I'm going with the AstroAI. Now, just need help finding a electric pressure washer that has the quick connects. Any ideas that can be under $200?
Thanks! for pressure washers under 200 please see video th-cam.com/video/pu6lfzM9iJ8/w-d-xo.html
Why do you prefer plastic-on-plastic as opposed to brass-on-plastic? I'd think that brass is always desirable for longevity. Does it tear up the plastic jug's threads?
Not a video topic I would have thought of, but thank you, as always! I don't really know anything about this product segment - it's actually something I was just telling myself a few days ago that I'd likely avoid DIYing most detailing work, but then, I'm debating if I shouldn't dismiss it so quickly, until I at least look at pricing on starter kit. This test certainly helped give me something to consider! Glad to see that a cheap tool gets the job done so well!
Paint and body work makes me nervous. Seems like a lot of complicated, touchy stuff, that's almost more art form and nuanced, rather than clear-cut and technical, the latter of which I'm more comfortable with. I certainly admire the work and setups at AMMO NYC and Obsessed Garage, but I'm really not sure how deep down those rabbit holes I want to play.
Yeah the plastic threads can get damaged screwing into brass, not a major deal if your careful.
I had a few requests to do one last year, but I for the life of me couldn’t find the harbor freight version in stock until a few months ago.
I agree, detailing and doing any kind of body work is a art. Definitely when it comes to paint matching.
I watch obsessed garage, his ocd is crazy. I can’t ever seem to buy anything in perfect condition to start with lol.
Yeah I was shocked the cheapest one 🏆, which I agree is a win.
I can't seem to find a review for the Westinghouse: Pressure Washer Foam Cannon - 3600 PSI, 1/4 in. Connector, Model # PWFC, would you please do review of this product, I value you thoughts. Great video. Thanks
Sadly it probably won't be until next year seeing I live up north, the temp has already dropped here.
Hello, the new MJJC foam cannon S V3.0 have released,may I know if you like to review it? Thanks!
Can you use a 1.1 oriface safely with a gas pressure washer? I have an old(ish) craftsman that I would like to utilize and the AstroAi is looking like the ticket. Thanks!
No shouldn't be an issue, it should actually foam better.
Great video! Used your link to buy the AstroAI. Thanks for the awesome review!
Thanks! Glad it was helpful and thanks for the support!
Nice comparison video especially with a consistent surface that you’re testing against.
Thanks! yeah I think it helps testing them on a consistent surface.
What does SPR mean?
SBR Short Barreled Rifle
@@Tools-Tested Thanks. Noob here👈🏼
Subscribed and liked the video because this is by far the best review. Ordered Tool Daily and AstraAi
Thanks for the sub! hopefully you like them.
I have the MTM foam gun that I use with a gas powered 3300 psi pressure washer and it doesn’t foam like it should. It comes out too watered down. I’ve tried adjusting the foam gun and the psi on the pressure washer, but it didn’t help. Any thoughts?
I would try the 1.1 orfice it comes with, if you already did that I would try different soap.
Great stuff man, appreciate the video. And glad you brought up the orifice fact, had no idea that was a thing.
Thanks, no problem! Yeah I didn't know either until I started doing research on them. Interesting to see the difference with the electric pressure washer.
You must try the Ridge Washer foam cannon - $20 and comes with a nice wash mit. Its the green label and comes with a 1.15 orifice. I'm getting amazing foam with the Ryobi 1800 psi electric pressure washer. I'm talking gas pressure washer - like foamage from this thing. Its a sleeper of a foam cannon.
Will do thanks for the info!
Can you use a wireless Ryobi and get the same results?
@@marls10191 Well I hooked it up to my gas Ryobi and far exceeded the results, so yes.
Do you have a link for it?
Thanks for the comparison. I bought because of the video.
No problem! Glad to hear it helped!
Is the 1.1mm office the way to go or
Yes typically it will produce better foam with the 1.1.
The tool daily # 2 works good when you change the orific to a 1.1 foams like crazy, the only problem I have with them is the bottle is cheaply made and broke on me now I can’t find a replacement
Yep that seems to be the common complaint with the tool daily.
What one would you recommend for the ryobi 1800
AstroAI would be my pick.
thanks for the video. this was super helpful!
No problem! Glad it was helpful!
I have a maybe dumb question, but can the Astro be mounted to a karcher high pressure washer, or do I need to order an adapter for it? Thanks for letting me know
Hard to say Karcher make different washer with different wands, it its a twist lock though u will need an adapter or different wand.
MJJC Foam Cannon OPTIMAL
What do you think about the blackline foam cannon?
Hard to say without testing it, and confirming what Orifice it has.
Only good multiple foam cannon comparison on TH-cam. Hope you do another thanks
Thanks! Hopefully part two will be out Sunday, took tomorrow off from work.
Thanks Astro AI really performed well.
No problem!
MJJC Foam Cannon Pro V2.0 is awesome and can be had for less than $80
Yeah I need to test that one at some point.
Great test. You put a lot of thought into this!
Thanks!
I ordered the AstroAI and it looks like it comes with a 1.25mm inner core diameter according to the manual.
It works well with my electric Ryobi pressure washer regardless.
Damn really? Do you have photos? I was gonna buy the Astro as well until I saw this comment.
I’m about to pull the trigger on the AstroAI. I have a electric Ryobi 1900.
Couldn't post a link, but I get the same performance he got in the review.
I'd recommend it, especially for the price.
Yeah spec sheet says 1.25mm, I actually measured 1mm. Im guessing they changed it and never updated the manual.
Thanks for following up on this. Just ordered the Astro
using a 1.0 orifice will trip your breaker on your washer or your outlet unless you're running on a dedicated 20Amp circuit 1.0 orifice reached 17.4 amps using the Astro A.I. cannon. I swapped for a 1.1 and went down to 14.2 amps ..safe
Gonna get my a tool daily 🤟thank you for the vid. Guys dont forget to use his referral links for his efforts.
Nice! No problem, I’m glad you found it useful. Thanks for using the link, every little bit keeps this channel operating.
9:55 You'll also need a tax stamp for that sbr conversion lmao
Your the first to comment on that lol.
@@Tools-Tested If you know, you know. Only 3% of us will get the joke.
How do you feel about the overall durability of the ASTRO? I have 8 technician work vans to keep clean
Heavy use I would go with the MTM personally, Astro is more DIY.
But for the price the Astro might be worth a shot.
I have a Black&Decker 1300TD , I don’t know what fits it from snow foam bottles , can someone help ? 😢
Thanks!
No problem!
Do any of these already have the 0 orifice?
No normal sizes are 1.1 or 1.25
Whats best orifice size?
1.1
Astroai vs Sooprinse?
I will add it to the list, but probably won't be until next year before I test them again.
Great video!
I think I'll pickup the new MTM Hydro foam cannon. I have the 1st gen version and used it for about 4- years, 100s of times. Best quality stuff you can get from MTM!
Thanks! Yeah the bottle is defiantly a big improvement on the new MTM. Yep I agree 100% if your using it a lot, hard to beat MTM products!
Keep the old one and just buy a new bottle! They’re pretty much the same thing
@@magictoaster806 Wish I saw your comment before I got the new model! Basically are the same things but the bottle 🤣
@Tools Tested A good video this is,may I know if it's ok for you to review our foam cannon S V3.0?Thanks in advance!☺
Thanks! I bought the MJJC v3 a few months ago, just waiting on the weather to warm up.
So good dear@@Tools-Tested
Why didn’t you include the MJJC cannon
Was at my budget for the video, I will be testing the MJJC in round 2 once the weather clears hopefully in a month.
I just bought the AstroAI from your link, but unfortunately it came with a 1.25mm orifice. I'll just have to buy a 1.1mm.
That’s interesting see I bought mine from that link.
Thank you for the amazing comparison and I will def buy the tool daily foam canon with my Ryobi 1.2 PW Electric . But can you suggest something affordable wand too sir? like the short Quick connect wand?
No problem!
Wands I currently cant speak for, I only have the MTM. At some point I would like to review and test some but it will be a while before I can.
can you please do best Presure washer short gun comparison video?
I bought the Astro Ai one and changed to a 1.1mm orifice. I'm using Chemical Guys Mr. Pink. I'm still not getting really thick foam. Could my gas pressure washer be too powerful? 2200 to 2900 PSI and 2.3 GPM.
I don't think the pressure washer is too powerful. I would try a higher concentration of soap if you haven't already, maybe run strait soap and see how it performs. Also might turn the adjustment in the opposite direct and see if it changes anything. I remember some of the ones I test they seemed to be labeled wrong on the nob.
If that dousing work maybe you received a defective one, with that flow and GPM you shouldn't have an issue.
@@Tools-Tested thanks so much. I'll give it a try
That is a crazy setup you have there between the gun and the pressure washer hose. Can you elaborate on that setup etc?
It's just some hydraulic fittings, a flow meter for water and a digital pressure gauge, with a MTM gun. That way I could get the GPM of the pressure washers and also working pressure at the same time using the same tip.
I’m going to try the AstroAi. It’s on sale, so why not.
Good value for the $ IMO
I just purchased the Astro AI and it came with a 1.25 orifice installed. There wasn't another one to change it out to. I was disappointed because I went off your recommendation and it didn't come with a 1 like you said but a 1.25.
Maybe mine was an error, I know it measured 1.03mm with my gauges while the manual says 1.25. I will probably order another one next year and see if that one measures the same.
Really?
Hey, the side of your building should be REALLY clean now 🤣😂. After watching this video, I became a subscriber!! Thank you
Lol yeah, the worst part is I had to do it almost twice because of the glare when the sun came out. I didn't notice it until editing the video...
Thanks for the sub!
You helped me big time thanks!
Glad I could help! No Problem!
Why is mine so runny. 1.1 value gas pressure washer 2900 psi. Chemical brother foam cannon.😢😢
Interesting maybe try different soap or high concentration of soap.
Can you please post a link to buy the 1.1 orifice? Great reviews!
Thanks! I added the links in the description.
Was looking at electric washers earlier today. But the 2500to3200 psi ones. 👍
Nice, I'm actually shocked how well the cheap Ryobi did. At some point I would like to test electric pressure washers.
How's your 30g doing? I'm almost at 500hrs.
@@Tools-Tested little under 300 now. Not any problems but wish the common complaint of a/c was better. Did Deere come through on the tractor issues?
@@marlondeere3039R Nice, yeah I agree AC could be better. I was going to look at adding some refrigerant but I haven’t had a chance to put gauges on it.
No tractor kinda been a disaster, finally got the brake valve fixed.
The dealer has been cycling through service mangers after the buyout. I think they are on #5 in two years…
Deere never came out on changing the wiper and stuff but like a month or so after that call they stopped making the 5r.
So yeah dealing with my dealer has been challenging to say the least.
FYI I moved the outdoor videos to a new channel.
Beaver Creek Acres
@@Tools-Tested thanks didn't know that I will definitely check it out and take care.
@Tools-Tested I owned 2 Ryobi electric PW and threw them away. Failing GFCI plug, Weak pump not keeping pressure, to full out failure.
I just picked up the Chemical Guys PW. I hope this one lasts longer than 3 to 6 months like the ryobis.
Couple of things. What’s the big deal about swapping to 1.1 orifice? It’s like $9.
Also, any thoughts on the active 2.0?
So if its being used on an electric pressure washer it will likely need the 1.1 so it foams vs runny suds, this is because most electric washers have a lower psi and gpm.
I did look at the Active 2.0 pressure washer, looks like a sold unit. But hard to say performance wise without testing it.
You might check out Obsessed Garage if u haven't already, Mike's testing is thorough.
th-cam.com/video/CVoQ5qyfxuw/w-d-xo.html
Great video man! I only hope to put out great reviews like this one day!!
Thanks! Yeah it takes a lot of time and work. Could do it without my full time job..
@@Tools-Tested WOW!! I believe it!! I actually bought the AstroAI after watching this. Just used it today a few hours ago and it is AMAZING FOR $23!!!!
Glad to hear!
Great review! Would love to see more car detail content!
Thanks! I will try and add some more in!
Not sure what model armor all you have but mine foams up great, able to change from horizontal to vertical. Using ryobi electric pw
Yes! Great video! Try the MJJC Foam cannon Pro V 2.O
Thanks! Will do!
It’s 90$ 😢
doesn't matter just the soap and AstroAi Hands down.
Yep!
Good video! Thank you
Thanks! no problem!
Thanks
No problem!
For the AstroAI orfice is it 1mm? 1.1mm? Becasue im trying to look at the comment it says 1.1 and 1.25 im so confused
It is 1mm
thanks
No problem!
This comment is for Tools Tested.
The AstroAI guy I talked to on the phone read the manual and said the orfice size must be 1.25 and wondered where you got the 1.0 information.
Yes the book says 1.25, but mine was around 1.0. I used a drill hole sizing tool.
Without ordering another one I can’t say If it was a error or if that’s how they all are coming now. But mine is definitely not a 1.25 or even a 1.1.
Awesome video, thanks
Thanks! No problem!